BGP Route Reflector Practice

Free BGP route reflector practice: a route enters an AS by eBGP, and you tap every router that ends up with it, or find the router that ignores a copy and say why. Check my answer names the rule from RFC 4456 and RFC 4271.

Problem 1

Which routers end up with the route?

Route 203.0.113.0/24by eBGP from AS 64500 into C2

Your picks
Why it ignores the copy

Answer to see the working.

Only each router's best path is passed on, and no problem here depends on which copy is best. As RFC 4456 says, a route from a client is reflected to the clients too, so the client it came from gets a copy back and ignores it by ORIGINATOR_ID. Only the sessions shown exist. The routers are made up for practice.

Practise the exams

Studying for a Cisco or Juniper routing exam? Start with the free real exam questions, then get the full pack.

Cisco SPCOR 350-501515 real exam questions · US$39
Free: 99 questionsGet the full pack
Cisco SPRI 300-510264 real exam questions · US$39
Free: 40 questionsGet the full pack
Cisco ENARSI 300-410620 real exam questions · US$39
Free: 113 questionsGet the full pack
Juniper JNCIS-SP JN0-36469 real exam questions · US$39
Free: 18 questionsGet the full pack
Juniper JNCIP-SP JN0-66496 real exam questions · US$39
Free: 24 questionsGet the full pack

Route reflector FAQ

Where does a route reflector send a route from a client?

RFC 4456 says to reflect it to all the non-client peers and also to the client peers. That is why clients do not need a full mesh between them.

Where does a route reflector send a route from a non-client?

To all its clients only. A non-client of the route reflector does not get it from the route reflector, so non-clients need their own sessions with each other.

What happens to a route learned by eBGP?

The router sends it to every iBGP peer, route reflector or not. That is not reflection, so the route goes out with no ORIGINATOR_ID and no CLUSTER_LIST.

Why does a normal iBGP router not pass a route on?

RFC 4271 says a router that receives an UPDATE from an internal peer shall not send it to other internal peers, unless the router is a route reflector. So a route that reaches a client or a plain iBGP router stops there.

What is the ORIGINATOR_ID?

An attribute a route reflector adds when it reflects a route, if it is not there yet. It carries the router ID of the router that brought the route into the AS. A router that gets a route with its own router ID as the ORIGINATOR_ID ignores it.

What is the CLUSTER_LIST?

The list of cluster IDs the route has been reflected through. Each route reflector puts its own cluster ID in front when it reflects. A route reflector that finds its own cluster ID in the list ignores the route, which stops loops.

Does the client that sent the route get it back?

In this drill, yes, as RFC 4456 says to reflect a client's route to the client peers. The client then ignores that copy because the ORIGINATOR_ID is its own router ID.

Why give two route reflectors the same cluster ID?

RFC 4456 says route reflectors in the same cluster can share a cluster ID so that one route reflector can discard routes from the others in its cluster. In the drill that shows up as a CLUSTER_LIST drop.

Does a route reflector reflect every path it has?

No. It picks its best path first and reflects only that. The drill never shows a problem where the choice of best path would change the answer.

Which exams cover route reflectors?

Cisco ENARSI 300-410 lists route reflectors under 1.11 Troubleshoot BGP, leaving out multiple route reflectors. Cisco SPRI 300-510 lists them under 1.4 and 1.5, and Juniper JNCIP-SP lists route reflection under BGP scaling mechanisms.

Sources
  • IETF, RFC 4456, BGP Route Reflection: where a route reflector sends a route from a client and from a non-client, the ORIGINATOR_ID and CLUSTER_LIST rules, one cluster ID shared by route reflectors in one cluster, and the full mesh example.
  • IETF, RFC 4271, A Border Gateway Protocol 4, section 9.2: a route from an internal peer is not sent to other internal peers unless the router is a route reflector.
  • Cisco exam topics: ENARSI 300-410 v1.1 (1.11.d) and SPRI 300-510 v1.1 (1.4.b and 1.5.b). Juniper: JNCIP-SP JN0-664 (route reflection under BGP scaling mechanisms).
  • Checked 21 November 2026. The tool's own approach: the routers, addresses and AS numbers are made up; only the sessions shown exist; every router honours ORIGINATOR_ID and only route reflectors check the CLUSTER_LIST; a route from a client goes back to that client, as the RFC wording says. Left out: policy and filters, next hop reachability, confederations, add path. An independent re-solver that reads only the cards, and passes only each router's best copy in many random orders, agreed with the drill on 5,000 generated problems. This is an independent practice tool, not made or endorsed by the IETF, Cisco or Juniper.

Checked 21 November 2026 against RFC 4456 (BGP Route Reflection) and RFC 4271 (BGP-4).

More free tools

All free tools