Juniper Networks JN0-364 JNCIS-SP Practice Questions with Explanations

Free Juniper Networks JN0-364 JNCIS-SP practice questions. 18 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.

JN0-364 practice questions

Question 1

Which two protocols would be used for dynamic routing in IPv6 environments? (Choose two.)

  • A. IS-IS
  • B. OSPFv2
  • C. BGP
  • D. IGMP
Show answer and explanation ▾

Correct answer: A, C

IS-IS and BGP both carry IPv6 routes. OSPFv2 is IPv4 only, and IGMP is a multicast group protocol, not a routing protocol.

Why the other options are wrong:

  • B. OSPFv2 supports IPv4 only; IPv6 needs OSPFv3.
  • D. IGMP manages multicast group membership on IPv4 and does not exchange routes.

Question 2

A BGP router receives two routes to the same prefix. One route has a higher local preference, while the other has a shorter AS path.In this scenario, which route would be selected?

  • A. The route with the lower origin code.
  • B. The route with the higher local preference.
  • C. The route with the shorter AS path.
  • D. The route with the lowest MED value.
Show answer and explanation ▾

Correct answer: B

BGP compares local preference before AS path length, so the route with the higher local preference wins even though the other route has a shorter path.

Why the other options are wrong:

  • A. Origin code is checked after local preference and AS path, and neither route is described as having a lower one.
  • C. AS path length is compared only after local preference, which already decides this case.
  • D. MED is compared later in the selection order and is not given for either route.

Question 3

During MPLS forwarding, which operation describes the act of imposing a label onto an unlabeled packet?

  • A. label swap
  • B. label pop
  • C. label push
  • D. label rewrite
Show answer and explanation ▾

Correct answer: C

A push adds a label to a packet that has none, which is what the ingress router does when traffic enters an LSP.

Why the other options are wrong:

  • A. A swap replaces the top label on a packet that is already labeled.
  • B. A pop removes a label from the packet.
  • D. Label rewrite is not an MPLS forwarding operation name.

Question 4

The MPLS Label Information Base (LIB) is stored in which table?

  • A. inet6.0
  • B. mpls.0
  • C. inet.0
  • D. inet.3
Show answer and explanation ▾

Correct answer: B

On Junos, the mpls.0 routing table holds the MPLS label information used for forwarding labeled packets.

Why the other options are wrong:

  • A. inet6.0 is the IPv6 unicast routing table.
  • C. inet.0 is the IPv4 unicast routing table.
  • D. inet.3 holds routes to MPLS LSP egress addresses used for BGP next-hop resolution, not the label table.

Question 5

By default, which routing table contains a list of all ingress LSPs?

  • A. inet.0
  • B. inet.1
  • C. inet.2
  • D. inet.3
Show answer and explanation ▾

Correct answer: D

The inet.3 table holds IPv4 MPLS path information: the egress address of each LSP, the LSP name and the outgoing interface. Junos uses this table only when the local router is the ingress node of an LSP.

Why the other options are wrong:

  • A. The inet.0 table holds IPv4 unicast routes such as direct, static and dynamically learned routes.
  • B. The inet.1 table is the IPv4 multicast forwarding cache.
  • C. The inet.2 table holds unicast routes used for multicast reverse path forwarding lookups.

Question 6

You are asked to add next-hop redundancy using VRRP for an IPv6 enabled service. The configured primary router must always be active when available, and the servers connected to the network must be able to ping their gateway.Which VRRP element is required to accomplish this requirement?

  • A. The accept-data parameter must be added to the VRRP configuration.
  • B. The preempt parameter must be added to the VRRP configuration.
  • C. The backup router requires the track parameter to track the primary router's interface.
  • D. Both routers running VRRP will require a static ARP entry to be configured for the VRRP VIP
Show answer and explanation ▾

Correct answer: A

By default, a VRRP primary that is not the address owner accepts only ARP packets sent to the virtual IP address, so pings to the gateway fail. Adding accept-data makes it accept all packets for the virtual address. Preemption is already on by default, so the configured primary retakes its role whenever it is available.

Why the other options are wrong:

  • B. Preemption is already enabled by default in Junos VRRP, and it does not let hosts ping the virtual address.
  • C. Tracking changes group priority and does not make the primary answer pings to the virtual address.
  • D. Static ARP entries are not part of what lets hosts ping the VRRP virtual address.

Question 7

What is the default route preference for an aggregate route?

  • A. 5
  • B. 130
  • C. 150
  • D. 180
Show answer and explanation ▾

Correct answer: B

In Junos, aggregate routes have a default route preference of 130. Lower values are preferred, so an aggregate loses to static and most interior routes but wins over OSPF external and BGP routes.

Why the other options are wrong:

  • A. A preference of 5 is the default for static routes.
  • C. A preference of 150 is the default for OSPF AS external routes.
  • D. A preference of 180 is not the default value for aggregate routes.

Question 8

You are using EBGP to connect to two upstream peers in the same AS. You want to make one of the links less preferred for traffic entering your network from the peer's AS.Which feature should you use to achieve this goal?

  • A. origin code
  • B. local preference
  • C. a route reflector
  • D. AS-path prepending
Show answer and explanation ▾

Correct answer: D

AS path prepending adds extra AS numbers to routes advertised on one link, so neighbors see a longer path and are less likely to select it. This reduces the traffic that the neighboring AS sends into your network over that link.

Why the other options are wrong:

  • A. The origin code is not the feature used to make one inbound link less preferred.
  • B. Local preference is not the feature used here to make a link less preferred for traffic entering from the peer's AS.
  • C. A route reflector is not used to steer traffic entering your network from another AS.

Question 9

How are routing loops prevented in internal BGP networks?

  • A. Internal BGP routes are never readvertised to other internal BGP neighbors.
  • B. External BGP routes are never readvertised to other external BGP neighbors.
  • C. Internal BGP routes are never readvertised to other external BGP neighbors.
  • D. External BGP routes are never readvertised to other internal BGP neighbors.
Show answer and explanation ▾

Correct answer: A

A BGP speaker that receives an update from an internal peer does not pass that routing information on to other internal peers, unless it acts as a route reflector. Because of this rule, routes learned over IBGP cannot circulate between internal peers and loop inside the AS.

Why the other options are wrong:

  • B. Routes learned from external peers are normally advertised to other external peers.
  • C. Routes learned from internal peers are normally advertised to external peers.
  • D. Routes learned from external peers are normally advertised to internal peers.

Question 10

Which feature allows Junos OS to perform recursive lookups for static route next hops?

  • A. discard
  • B. resolve
  • C. reject
  • D. next-table
Show answer and explanation ▾

Correct answer: B

The resolve option lets a static route use a next hop that is not directly connected. Junos resolves that next hop recursively through the inet.0 and inet.3 routing tables.

Why the other options are wrong:

  • A. The discard option is not the option that resolves a next hop that is not directly connected.
  • C. The reject option is not the option that resolves a next hop that is not directly connected.
  • D. The next-table option is not the option that resolves a next hop address recursively.

Question 11

You are troubleshooting a Level 1 IS-IS router that has an adjacency with a Level 1/2 router.Which two statements are correct in this scenario?

(Choose two.)

  • A. The Level 1/2 router merges Level 1 and Level 2 into one complete topology.
  • B. The Level 1/2 router sees the Level 1 network and the Level 2 network as two separate topologies.
  • C. The Level 1 router will only learn the topology of the Level 1 network.
  • D. The Level 1 router will learn the full topology of the Level 2 network.
Show answer and explanation ▾

Correct answer: B, C

IS-IS keeps link-state information per level: all routers within a level hold a complete database for that level, and flooding stops at level boundaries. A Level 1/Level 2 router therefore sees two separate topologies, while a Level 1 router learns only its Level 1 area and sends other traffic toward a Level 2 system.

Why the other options are wrong:

  • A. A Level 1/Level 2 router keeps the two levels separate and does not merge them into one topology.
  • D. A Level 1 router does not learn the Level 2 topology and instead routes outside traffic toward a Level 2 system.

Question 12

What happens if an IS-IS router receives a link-state PDU with a higher sequence number than the one in its database?

  • A. It sends a CSNP to request confirmation from the source of the link-state PDU.
  • B. It updates its database and floods the link-state PDU.
  • C. It resets the adjacency with the source of the link-state PDU.
  • D. It ignores the link-state PDU
Show answer and explanation ▾

Correct answer: B

When an IS-IS router receives a link-state PDU newer than its stored copy, it stores the new PDU in its database and marks it for sending on all other circuits. The newer information is therefore flooded through the area.

Why the other options are wrong:

  • A. A newer link-state PDU is accepted directly and does not trigger a CSNP request to its source.
  • C. Receiving a newer link-state PDU does not reset the adjacency.
  • D. A newer link-state PDU replaces the stored copy and is not ignored.

Question 13

In IS-IS, what would you use to control which external routes are installed in the routing table?

  • A. export policy
  • B. route preference
  • C. import policy
  • D. interface metric
Show answer and explanation ▾

Correct answer: C

An IS-IS import policy is applied to routes being imported from IS-IS into the Junos routing table. It is used to filter or restrict routes, so it controls which external routes are installed.

Why the other options are wrong:

  • A. An export policy is not what filters the IS-IS routes installed in the local routing table.
  • B. Route preference is not used to filter which IS-IS external routes are installed.
  • D. An interface metric changes path cost and does not filter which external routes are installed.

Question 14

During OSPF neighbor establishment, which packet type is used to describe the contents of the link-state database?

  • A. Link-State Request (LSR)
  • B. hello packet
  • C. Database Description (DBD)
  • D. Link-State PDU (LSP)
Show answer and explanation ▾

Correct answer: C

Database Description packets summarize the contents of the link-state database during adjacency forming. Each one describes a set of LSAs, letting neighbors see which LSAs they still need to request.

Why the other options are wrong:

  • A. Link State Request packets ask for specific LSAs and serve database download, not description.
  • B. Hello packets discover and maintain neighbors.
  • D. Link-State PDU is not one of the OSPF packet types.

Question 15

You are asked to configure interfaces on Juniper devices to support dual VLAN tags.In this scenario, which two interface statements would accomplish this task? (Choose two.)

  • A. vlan-tagging
  • B. flexible-vlan-tagging
  • C. stacked-vlan-tagging
  • D. gigether-options
Show answer and explanation ▾

Correct answer: B, C

The stacked-vlan-tagging statement lets an Ethernet interface receive and forward dual-tag 802.1Q frames. The flexible-vlan-tagging statement supports both single-tag and dual-tag logical interfaces on the same port, so it also supports dual tags.

Why the other options are wrong:

  • A. The vlan-tagging statement supports single-tag 802.1Q frames only.
  • D. The gigether-options statement is not one of the statements that enable dual VLAN tags.

Question 16

What are three default BGP advertisement rules? (Choose three.)

  • A. IBGP peers do not advertise routes received from EBGP peers to other IBGP peers.
  • B. IBGP peers do not advertise routes received from IBGP peers to other IBGP peers.
  • C. EBGP peers advertise routes learned from IBGP or EBGP peers to other EBGP peers.
  • D. IBGP peers advertise routes received from EBGP peers to other IBGP peers.
  • E. IBGP peers advertise routes received from IBGP peers to other IBGP peers
Show answer and explanation ▾

Correct answer: B, C, D

By default, Junos readvertises all active BGP routes to all BGP speakers, so EBGP peers get routes learned from IBGP or EBGP and IBGP peers get routes learned from EBGP. The exception is that an IBGP speaker does not readvertise routes learned from another IBGP speaker unless it is a route reflector.

Why the other options are wrong:

  • A. IBGP peers do advertise routes received from EBGP peers to other IBGP peers.
  • E. IBGP peers do not readvertise routes learned from IBGP peers to other IBGP peers by default.

Question 17

Which IPv6 extension header is used to specify intermediate nodes for a packet’s path?

  • A. hop-by-hop options
  • B. routing
  • C. destination options
  • D. fragment
Show answer and explanation ▾

Correct answer: B

The IPv6 Routing header lets the source list one or more intermediate nodes that the packet must visit on the way to its destination.

Why the other options are wrong:

  • A. The Hop-by-Hop Options header carries options examined by every node on the path, not a list of nodes to visit.
  • C. The Destination Options header carries options for the destination node only.
  • D. The Fragment header is used to send packets larger than the path MTU.

Question 18

What are three extension headers supported by IPv6? (Choose three.)

  • A. protocol
  • B. hop-by-hop options
  • C. header checksum
  • D. destination options
  • E. fragment
Show answer and explanation ▾

Correct answer: B, D, E

Extension headers carry optional information after the main IPv6 header. A full IPv6 implementation includes the Hop-by-Hop Options, Fragment, Destination Options, Routing, Authentication and Encapsulating Security Payload extension headers.

Why the other options are wrong:

  • A. Protocol is not one of the IPv6 extension headers.
  • C. Header checksum is not one of the IPv6 extension headers.

That was 18 of 69.

The full Juniper Networks JN0-364 JNCIS-SP pack has all 69 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.

Get the full pack

Not ready yet? Get the first 18 free as one PDF by email. Get the Half Pack →

About the JN0-364 exam

These 18 Juniper Networks JN0-364 JNCIS-SP questions are free here, and as a free PDF by email.

They are drawn from the same bank as the full JN0-364 pack, which has 69 questions in total.

Back to blog