Cisco 300-510 SPRI Practice Questions with Explanations
Free Cisco 300-510 SPRI practice questions. 40 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.
300-510 practice questions
Question 1
A network consultant is troubleshooting IS-IS instances to identify why a routing domains is having communication problems between the two instances.
Which description of the possible cause of issues in the routing domain is true?
- A. The same interface cannot be advertised in two different IS-IS instances
- B. The IS-IS "ISP" and "ISP2" instances are unrelated and unable to intercommunicate
- C. The configured IS-IS NSEL value is not allowing the routing systems to establish a neighborship
- D. The interface mode ip router is-is command was not included in the script
Show answer and explanation ▾
Correct answer: A
An interface can belong to only one IS-IS instance, so advertising the same interface in two different instances is a configuration fault that disrupts communication between the routing domains.
Why the other options are wrong:
- B. Two separate IS-IS instances not exchanging routes with each other is normal behavior and does not describe a fault by itself.
- C. The NSEL value is not what stops the two instances from communicating.
- D. Whether the interface command is present is not the cause of the problem between the two instances.
Question 2
What is used by SR-TE to steer traffic through the network?
- A. shortest path calculated by IGP
- B. dynamic rules
- C. path policy
- D. explicit maps
Show answer and explanation ▾
Correct answer: C
SR-TE steers traffic with a path policy, called an SR policy, that is applied at the head end and carries the segment list or the computed path the traffic must follow.
Why the other options are wrong:
- A. The shortest path calculated by the IGP is the default forwarding result, not the mechanism SR-TE uses to steer traffic.
- B. Dynamic rules is not a steering construct in SR-TE.
- D. Explicit maps is not an SR-TE term; explicit paths are defined inside a policy.
Question 3
For which reason can two devices fail to establish an OSPF neighbor relationship?
- A. The two devices have different process IDs
- B. The two devices have different network types
- C. The two devices have different router IDs
- D. The two devices have the same area ID
Show answer and explanation ▾
Correct answer: B
OSPF neighbors on a link must agree on parameters such as the network type, so a mismatch like broadcast on one side and point-to-point on the other prevents a working adjacency.
Why the other options are wrong:
- A. OSPF process IDs are locally significant and do not need to match between neighbors.
- C. Router IDs must be unique, so different router IDs are expected and do not block the relationship.
- D. Neighbors on a link must be in the same area, so a shared area ID is required, not a fault.
Question 4
Which statement about enabling segment routing for IGPs is true?
- A. Segment routing must first be enabled under then routing process and then globally
- B. Segment routing must first be enabled globally and then under the routing process
- C. Segment routing can be enabled only under the routing process
- D. Segment routing can be enabled only globally
Show answer and explanation ▾
Correct answer: B
Segment routing is enabled globally first and then under the IGP routing process, so that the protocol can advertise segment information.
Why the other options are wrong:
- A. The order is reversed, because global enablement comes before the routing process configuration.
- C. Enabling it only under the routing process is not enough, because the global enablement is also required.
- D. Global enablement alone does not turn it on for the IGP, which also needs it under the routing process.
Question 5
Which task is performed when troubleshooting LDP?
- A. Execute the ping utility to generate information about the MAC addresses used along the path
- B. Verify that MPLS is disabled globally and enabled on the necessary interfaces in a per-interface basis
- C. Execute the traceroute utility to generate information about the labels used along the path
- D. Verify that Cisco Express Forwarding has been disabled on the network
Show answer and explanation ▾
Correct answer: C
Traceroute across an MPLS network reports the labels used at each hop, so it helps verify label bindings and the label switched path when troubleshooting LDP.
Why the other options are wrong:
- A. Ping does not report the MAC addresses used along the path.
- B. MPLS must be enabled on the needed interfaces, so verifying that it is disabled globally is not a troubleshooting task.
- D. Cisco Express Forwarding is required for MPLS forwarding, so it must be enabled, not disabled.
Question 6
What can be used to determine a path from the head-end to a tail-end router when implementing SR-TE with a head-end, with little information on the network topology?
- A. traffic controller
- B. path computation engine
- C. tail-end router
- D. SNMP server
Show answer and explanation ▾
Correct answer: B
A path computation engine holds the network topology and calculates the path, so a head end with little topology knowledge can request the path to the tail end from it.
Why the other options are wrong:
- A. A traffic controller is not the element that computes the path for the head end.
- C. The tail-end router is only the destination of the path and does not compute it.
- D. An SNMP server is a monitoring and management tool and does not compute SR-TE paths.
Question 7
Which two conditions must be met before separate ISPs can provide interdomain multicast routing? (Choose two.)
- A. Each ISP must configure MSDP to connect its individual multicast administrative domain to the domains at other ISPs.
- B. Each ISP must dedicate a single router to handle multicast traffic between providers.
- C. Each ISP must replace its RP assignment with a global RP.
- D. Each ISP must configure its network to use PIM-DM.
- E. Each ISP must support intradomain multicast routing.
Show answer and explanation ▾
Correct answer: A, E
MSDP lets each ISP's multicast domain share active source information with the other ISPs, and each ISP must already run multicast routing inside its own domain.
Why the other options are wrong:
- B. No single dedicated router is required to handle multicast between providers.
- C. ISPs keep their own RP assignments and connect them with MSDP instead of using a global RP.
- D. PIM-DM is not what interdomain multicast relies on, and ISPs are not required to use it.
Question 8
An engineer is troubleshooting a connectivity issue across the MPLS network and is verifying the forwarding behavior of packets.
Which table does the engineer look at to verify the forwarding behavior of an IP packet as it enters the MPLS network at the ingress LSR?
- A. LFIB
- B. LIB
- C. RIB
- D. FIB
Show answer and explanation ▾
Correct answer: D
An ingress LSR receives an unlabeled IP packet and looks it up in the FIB, which holds the label to impose and the outgoing interface.
Why the other options are wrong:
- A. The LFIB is used for packets that already carry a label, not for the IP packet arriving at the ingress.
- B. The LIB stores label bindings and is not the table used to forward packets.
- C. The RIB holds routes, but forwarding decisions are made from the FIB.
Question 9
You have configured MSDP peering between two autonomous systems that pass traffic between two sites, but the peering has failed to come up.
Which task do you perform to begin troubleshooting the problem?
- A. Verify that multicast has been disabled globally
- B. Verify that PIM-DM is configured on the source interface
- C. Verify that both source interfaces are reachable from both peers
- D. Verify that the two MSDP peers allow asymmetric routing
Show answer and explanation ▾
Correct answer: C
MSDP peers connect over TCP between their configured source interfaces, so you start by verifying that each source interface address is reachable from both peers.
Why the other options are wrong:
- A. Multicast must be enabled for MSDP, so verifying that it is disabled globally is not the right check.
- B. MSDP does not need PIM-DM on the source interface, so that is not where troubleshooting begins.
- D. Allowing asymmetric routing between the peers is not a requirement checked when an MSDP peering fails to come up.
Question 10
For which reason do you deploy BGP confederations within a BGP transit backbone?
- A. to support a larger number of eBGP peer sessions
- B. to increase the number of routes that can be redistributed between the running IGP and BGP
- C. to reduce the number of eBGP routes that must be shared between autonomous systems
- D. to reduce the number of iBGP peering sessions
Show answer and explanation ▾
Correct answer: D
A confederation splits a large AS into smaller sub-ASes that run full mesh internally, which cuts the number of iBGP peering sessions a transit backbone needs.
Why the other options are wrong:
- A. Confederations do not exist to support more eBGP peer sessions.
- B. They have no effect on how many routes can be redistributed between the IGP and BGP.
- C. They do not reduce the eBGP routes that must be shared between autonomous systems.
Question 11
Which feature is used in multicast routing to prevent loops?
- A. STP
- B. inverse ARP
- C. RPF
- D. split horizon
Show answer and explanation ▾
Correct answer: C
Reverse Path Forwarding accepts a multicast packet only on the interface that leads back to the source, which prevents forwarding loops.
Why the other options are wrong:
- A. STP prevents Layer 2 loops and is not the multicast routing loop prevention feature.
- B. Inverse ARP maps addresses on Frame Relay circuits and has no role in multicast loop prevention.
- D. Split horizon is a distance vector routing technique, not the multicast loop prevention mechanism.
Question 12
After you change the IP address on an IOS XR router, you cannot ping the new address.
Which step did you forget to complete?
- A. commit the configuration
- B. roll back the configuration
- C. merge the configuration
- D. save the running configuration
Show answer and explanation ▾
Correct answer: A
IOS XR stages configuration changes in a target configuration that becomes active only after the commit command, so the new IP address stays inactive until you commit.
Why the other options are wrong:
- B. Rolling back the configuration reverts a committed change and would not activate the new address.
- C. Merging is a way of loading configuration, and it does not apply staged changes.
- D. Saving the running configuration is not needed to activate a change, because commit is what applies it.
Question 13
Which two statements about route reflectors are true? (Choose two.)
- A. Routes received from nonclient peers are reflected to route reflector clients as well as nonclient peers.
- B. Routes received from nonclient peers are reflected to route reflector cluster as well as OSPF peers.
- C. If a router received an iBGP route with the originator-ID attribute set to its own router ID, the route is discarded.
- D. Routes received from a route reflector client is reflected to other clients and nonclient peers.
- E. If a route reflector receives a route with a cluster-list attribute containing a different cluster ID, the route is discarded.
Show answer and explanation ▾
Correct answer: C, D
A route reflector reflects routes from a client to other clients and to nonclient peers, and a router discards an iBGP route whose originator ID is its own router ID to prevent loops.
Why the other options are wrong:
- A. Routes from nonclient peers are reflected only to clients, not to other nonclient peers.
- B. Routes from nonclient peers are reflected to clients, and they are not reflected to OSPF peers.
- E. A route is discarded when its cluster list contains the router's own cluster ID, not a different one.
Question 14
Which two statements about mapping multicast IP addresses to MAC addresses are true? (Choose two.)
- A. All mapped multicast MAC addresses begin with 0x0100.5E
- B. The router performs the mapping before it hands the packet off to a switch
- C. All multicast MAC addresses end with 0x0100.5E
- D. The mapping process may generate overlapping addresses, which can cause receivers to receive unwanted packets
- E. All destination MAC addresses begin with an octet of binary 1s
Show answer and explanation ▾
Correct answer: A, D
Mapped IPv4 multicast MAC addresses all begin with 0100.5E, and because only 23 bits of the group address are used, different groups can map to the same MAC and cause receivers to get unwanted packets.
Why the other options are wrong:
- B. The mapping is not a step done only by the router before the switch, because any device sending multicast frames derives the MAC from the group address.
- C. Multicast MAC addresses begin with 0100.5E and do not end with it.
- E. A destination MAC made of all 1s is the broadcast address, and multicast addresses do not begin with an octet of binary 1s.
Question 15
You have configured routing policies on a Cisco IOS XR device with routing policy language.
Which two statements about the routing policies are true? (Choose two.)
- A. The routing policies affect BGP-related routes only.
- B. If you make edits to an existing routing policy without pasting the full policy into the CLI, the previous policy is overwritten.
- C. You can change an existing routing policy by editing individual statements.
- D. The routing policies are implemented in a sequential manner.
- E. The routing policies are implemented using route maps.
Show answer and explanation ▾
Correct answer: B, D
Routing policy language evaluates statements in sequence, and editing a policy without pasting the full definition replaces the previous policy.
Why the other options are wrong:
- A. Routing policies on IOS XR apply to other protocols too, such as OSPF and IS-IS, not only BGP.
- C. An existing policy is replaced as a whole and not changed by editing individual statements.
- E. Routing policy language is a separate mechanism and does not use route maps.
Question 16
Which cost is the default when redistributing routes from BGP to OSPF?
- A. 20
- B. 1
- C. infinite
- D. automatic
Show answer and explanation ▾
Correct answer: B
OSPF assigns a default metric of 20 to redistributed routes, but routes redistributed from BGP get a default cost of 1.
Why the other options are wrong:
- A. 20 is the default metric for other redistributed sources, not for BGP.
- C. Infinite is not an OSPF default redistribution cost.
- D. Automatic is not a default OSPF redistribution cost.
Question 17
Which command is used to enable BIDIR-PIM under global configuration mode for Cisco IOS XE Sofware?
- A. ip pim bidir-enable
- B. ipv4 pim bidir-enable
- C. ip multicast-routing
- D. ip pim bidir
Show answer and explanation ▾
Correct answer: A
On Cisco IOS XE the global command ip pim bidir-enable turns on BIDIR-PIM.
Why the other options are wrong:
- B. The ipv4 pim form is not the IOS XE global command for enabling BIDIR-PIM.
- C. ip multicast-routing enables multicast routing in general and does not enable BIDIR-PIM.
- D. ip pim bidir is not a valid global command.
Question 18
Which output from the show isis interface command helps an engineer troubleshoot an IS-IS adjacency problem on a Cisco IOS-XR platform?
- A. metric
- B. priority
- C. circuit type
- D. hello interval
Show answer and explanation ▾
Correct answer: C
The circuit type in show isis interface shows whether the interface runs level 1, level 2 or both, and a circuit type mismatch between neighbors can stop an adjacency from forming.
Why the other options are wrong:
- A. The metric affects path selection and does not prevent an adjacency.
- B. The priority only influences DIS election and does not explain a missing adjacency.
- D. IS-IS hellos carry the hold time, so hello intervals can differ and do not prevent an adjacency.
Question 19
A network engineer is troubleshooting OSPF multiarea.
Which Cisco IOS XR feature should the engineer use in order to streamline OSPF issue?
- A. hierarchical CLI
- B. DR support for topology management
- C. routing process enabled by default on all interfaces
- D. show ip ospf topology command
Show answer and explanation ▾
Correct answer: A
The hierarchical CLI in IOS XR lets you configure areas and their interfaces in a nested structure under the OSPF process, which streamlines OSPF multiarea configuration and troubleshooting.
Why the other options are wrong:
- B. DR support for topology management is not an IOS XR feature used to streamline OSPF.
- C. The routing process is not enabled by default on all interfaces.
- D. A show command only displays information and does not streamline multiarea OSPF configuration the way the hierarchical CLI does.
Question 20
For which reason can two BGP peers fail to establish a neighbor relationship?
- A. Their BGP send-community strings are misconfigured
- B. Their BGP timers are mismatched
- C. Their remote-as numbers are misconfigured
- D. They are both activated under an IPv4 address family
Show answer and explanation ▾
Correct answer: C
BGP peers must agree on each other's AS number, so a misconfigured remote-as prevents the neighbor relationship from being established.
Why the other options are wrong:
- A. Attribute-sending settings on a peer do not decide whether a session forms.
- B. BGP timers are negotiated, so a mismatch does not prevent the session from coming up.
- D. Activating both peers under an IPv4 address family is normal and does not cause a failure.
Question 21
In a PIM-SM environment, which mechanism determines the traffic that a receiver receives?
- A. The receiver explicitly requests its desired traffic from the RP on the shared tree.
- B. The receiver explicitly requests traffic from a single source, which responds by forwarding all traffic.
- C. The RP on the shared tree floods traffic out of all PIM configured interfaces.
- D. The receiver explicitly requests traffic from each desired source, which responds by sending all traffic.
Show answer and explanation ▾
Correct answer: A
In PIM-SM a receiver explicitly requests the traffic it wants through the RP on the shared tree, and traffic flows only where requested.
Why the other options are wrong:
- B. A receiver does not request traffic from one source that then forwards everything.
- C. The RP does not flood traffic out of all PIM interfaces, which is dense mode behavior.
- D. Receivers join through the RP first, and sources do not send all traffic on request.
Question 22
Which statement about BFD on Cisco IOS XR Software is true?
- A. Cisco IOS XR router must use LDP to route back to the Cisco IOS router to establish the peer relationship.
- B. Cisco IOS XR Software does not support BFD multihop for IPv4.
- C. Cisco IOS XR router must use dynamic routing or a static route back to the Cisco IOS router to establish the peer relationship.
- D. BFD is not compatible between Cisco IOS XR and Cisco IOS Software.
Show answer and explanation ▾
Correct answer: C
BFD between IOS XR and IOS needs the XR router to have a route back to the IOS router, learned through dynamic routing or a static route, to establish the peer relationship.
Why the other options are wrong:
- A. LDP is not what the XR router uses to route back for BFD.
- B. IOS XR does support BFD multihop for IPv4.
- D. BFD is compatible between IOS XR and IOS software.
Question 23
Which two routing protocols have extensions capable of running SRv6? (Choose two.)
- A. OSPF
- B. BGP
- C. RIP
- D. IGRP
- E. EIGRP
Show answer and explanation ▾
Correct answer: A, B
OSPF and BGP both have extensions that carry SRv6 information, such as locators and SIDs.
Why the other options are wrong:
- C. RIP has no SRv6 extensions.
- D. IGRP is a legacy protocol with no SRv6 extensions.
- E. EIGRP has no SRv6 extensions.
Question 24
Which two characteristics unique to SSM when compared to ASM are true? (Choose two.)
- A. It uses SPT switchover
- B. It uses (*,G) exclusively
- C. It uses IGMPv3
- D. It uses RP
- E. It uses (S,G) exclusively
Show answer and explanation ▾
Correct answer: C, E
SSM relies on IGMPv3 so receivers can name the source they want, and it builds only (S,G) state, which sets it apart from ASM.
Why the other options are wrong:
- A. SPT switchover is part of ASM and is not needed in SSM, which joins the source tree directly.
- B. (*,G) state is used by ASM, and SSM does not use it.
- D. SSM does not use an RP.
Question 25
What are three requirements for a static IPv6-in-IPv4 tunnel? (Choose three.)
- A. A dynamic IPv6 address must be configured
- B. A dynamic IPv4 address must be configured
- C. A static IPv4 address must be configured
- D. A static IPv6 address must be configured
- E. Each tunnel endpoint must support IPv4 and IPv6
- F. Cisco Express Forwarding must be enabled
Show answer and explanation ▾
Correct answer: C, D, E
A static IPv6-in-IPv4 tunnel needs a statically configured IPv4 address and IPv6 address, and each tunnel endpoint must support both IPv4 and IPv6.
Why the other options are wrong:
- A. A dynamic IPv6 address is not a requirement for a static tunnel.
- B. A dynamic IPv4 address is not a requirement for a static tunnel.
- F. Cisco Express Forwarding is not listed as a requirement for a static IPv6-in-IPv4 tunnel.
Question 26
What are two differences between OSPF and IS-IS? (Choose two.)
- A. Unlike IS-IS routers, an OSPF router belongs to only one area in addition to the backbone area
- B. OSPF uses a router ID to identify a router, and IS-IS uses a system ID
- C. OSPF is a link-state routing protocol, and IS-IS is a distance-vector routing protocol
- D. Unlike OSPF, IS-IS supports virtual links
- E. OSPF elects a DR and BDR, and IS-IS elects a DIS
Show answer and explanation ▾
Correct answer: B, E
OSPF identifies a router with a router ID while IS-IS uses a system ID taken from the NET. On multi-access segments OSPF elects a DR and BDR, whereas IS-IS elects a single DIS.
Why the other options are wrong:
- A. An OSPF router can belong to several areas through multiple interfaces, so this does not describe a real difference.
- C. IS-IS is a link-state protocol, not a distance-vector protocol.
- D. Virtual links are an OSPF feature, not an IS-IS one.
Question 27
What is the purpose of a BGP confederation?
- A. It reduces the number of iBGP peers and increases stability
- B. It improves service by increasing the number of simultaneous iBGP peering sessions
- C. It redirects traffic away from route reflectors, which reduces their operating load
- D. It limits the number of routes a device receives from its peers, which reduces CPU load
Show answer and explanation ▾
Correct answer: A
A confederation splits an AS into smaller sub-ASes, so full iBGP meshing is only needed inside each one. This cuts the number of iBGP peerings and makes the network more stable and manageable.
Why the other options are wrong:
- B. Confederations reduce, not increase, the number of iBGP sessions.
- C. Confederations are an alternative to route reflectors and do not redirect traffic away from them.
- D. Limiting routes received from peers is done with filters or prefix limits, not confederations.
Question 28
What are two features of dual-stack? (Choose two.)
- A. It is implemented without excessive processing power.
- B. It supports IPv4 and IPv6 traffic on the same infrastructure.
- C. It allows an engineer to stack multiple Layer 2 switches to serve as a single switching unit.
- D. It requires tunneling IPv6 traffic over an IPv4 infrastructure.
- E. It securely routes and tunnels traffic between separate sites over the Internet.
Show answer and explanation ▾
Correct answer: A, B
Dual-stack runs IPv4 and IPv6 side by side on the same infrastructure, so both kinds of traffic are carried natively. It needs no tunneling or translation, which keeps processing demands low.
Why the other options are wrong:
- C. Stacking Layer 2 switches into one unit is switch stacking, not dual-stack.
- D. Dual-stack carries IPv6 natively and does not require tunneling over IPv4.
- E. Securely tunneling traffic between sites over the Internet describes a VPN, not dual-stack.
Question 29
When deploying a nationwide network of routers, what is the benefit of using BGP confederations?
- A. availability
- B. scalability
- C. security
- D. automatability
Show answer and explanation ▾
Correct answer: B
Confederations break a large AS into sub-ASes so that full iBGP meshes are not needed everywhere. That makes a nationwide network easier to grow, which is a scalability benefit.
Why the other options are wrong:
- A. Availability is not the main benefit confederations provide.
- C. Confederations do not add security to BGP sessions.
- D. Confederations do not automate configuration or operations.
Question 30
A network operator working for a telecommunication company with an employee id: 4074:92:707 is planning to implement the Nonstop Forwarding (NSR) feature on the customer’s core network. After getting the configuration ready for NSR. on which router should the operator implement NSR changes?
- A. on the CE router
- B. on the ASBR router
- C. on the ABR router
- D. on the PE router
Show answer and explanation ▾
Correct answer: D
Nonstop routing keeps routing and label state across a route processor switchover, which matters most on the PE routers that carry the provider's customer traffic. That is where the operator applies the NSR changes.
Why the other options are wrong:
- A. The CE router belongs to the customer and is not where the provider applies NSR.
- B. An ASBR is not the router where the NSR changes are applied in this scenario.
- C. An ABR is not the router where the NSR changes are applied in this scenario.
Question 31
Which difference must an engineer consider when choosing whether to implement OSPF or IS-IS as the routing protocol on the network?
- A. The OSPF DR election process is deterministic, and the IS-IS DS election process is not deterministic.
- B. To support fast convergence, OSPF uses the LSA arrival timer and IS-IS uses the PRC-interval timer.
- C. IS-IS supports ordinary, stub, totally-stub, and NSSA areas, but OSPF supports only stub areas.
- D. IS-IS links are associated with either a Level 1 area or a Level 2 area at one time, but OSPF links are associated with multiple areas at one time.
Show answer and explanation ▾
Correct answer: B
For fast convergence OSPF tunes the LSA arrival timer, while IS-IS tunes the PRC interval that controls how soon a route calculation runs after a topology change.
Why the other options are wrong:
- A. IS-IS DIS election is preemptive and predictable, so describing it as not deterministic is wrong.
- C. OSPF supports stub, totally stubby, and NSSA areas as well, so this is not a difference.
- D. OSPF interfaces belong to a single area, while IS-IS links can be Level 1, Level 2, or both.
Question 32
While configuring Cisco NSF awareness, a network engineer enters the bgp graceful-restart command after the BGP session is established in a router that runs IOS XE Software. Graceful restart capabilities are not exchanged. Which two actions should be taken? (Choose two.)
- A. Reload the router
- B. Verify that BGP route dampening is configured
- C. Reduce BGP convergence time
- D. Issue the clear ip bgp * command
- E. Issue the show ip bgp neighbors command.
Show answer and explanation ▾
Correct answer: A, D
Graceful restart capability is exchanged only when a BGP session is established. Enabling it afterward needs a session reset, so the engineer reloads the router or issues clear ip bgp * to renegotiate.
Why the other options are wrong:
- B. Route dampening is unrelated to graceful restart capability exchange.
- C. Reducing convergence time does not make the capabilities get exchanged.
- E. The show command only displays the neighbor state and does not renegotiate the capability.
Question 33
What is the difference between basic IS-IS and OSPF packet types?
- A. IS-IS and OSPF use area packets, but only IS-IS uses sequence number packets.
- B. IS-IS and OSPF use link-state update packets, but only OSPF uses link-state ACK packets.
- C. IS-IS and OSPF use Hello packets, but only OSPF uses DBD packets.
- D. IS-IS and OSPF use link-state update packets, but only IS-IS uses DBD packets.
Show answer and explanation ▾
Correct answer: C
Both protocols use Hello packets to form adjacencies, but only OSPF has database description packets. IS-IS synchronizes its database with sequence number packets instead.
Why the other options are wrong:
- A. Neither protocol uses area packets, and OSPF has no sequence number packets.
- B. Both protocols use acknowledgements, so this is not a difference.
- D. IS-IS does not use database description packets, which are an OSPF feature.
Question 34
Which difference should be considered when intradomain or interdomain multicast routing is implemented?
- A. Interdomain multicast routing relies on PIM-DM, and intradomain multicast routing relies on PIM-SM
- B. Interdomain multicast routing uses BIDR-PIM to establish neighbor relationships between AS, and intradomain multicast routing uses MSDP
- C. A network uses intradomain multicast routing without interdomain routing, but networks that use interdomain multicast routing must also apply intradomain routing
- D. Interdomain multicast routing requires an IS-IS or OSPF neighbor relationship between the domains, but intradomain multicast routing requires only BGP
Show answer and explanation ▾
Correct answer: C
Intradomain multicast routing can run alone inside a network. Interdomain multicast builds on it, so any network using interdomain routing must also run intradomain routing.
Why the other options are wrong:
- A. Interdomain multicast does not depend on PIM-DM, and intradomain use is not limited to PIM-SM.
- B. MSDP is used between domains, so the roles in this statement are reversed.
- D. Interdomain multicast uses BGP between domains and does not need an IS-IS or OSPF relationship across them.
Question 35
An engineer is troubleshooting slow performance issues on a customer’s network after the last multicast configuration change was applied on it.
While checking the running configuration on the router, the engineer notices there are many ip igmp join-group commands applied on several interfaces of the router which caused the high CPU utilization usage.
What action must the engineer take to solve this issue?
- A. Configure all router interfaces to be process-switched by increasing the query interval
- B. Remove ip igmp join-group command on all unnecessary interfaces
- C. Remove unnecessary members from the IGMP group
- D. Configure ip igmp static-group command on all interfaces
Show answer and explanation ▾
Correct answer: D
The ip igmp join-group command makes the router itself a receiver and process-switches the traffic, which drives up CPU. The ip igmp static-group command forwards the traffic onto the interface without that overhead.
Why the other options are wrong:
- A. Process switching adds CPU load, and a longer query interval does not remove the join-group cause.
- B. Removing the commands only on unnecessary interfaces leaves join-group on the rest, so the router still process-switches that traffic.
- C. The problem lies in the join-group commands, not in the group's members.
Question 36
What is the difference between a source tree and a shared tree in a multicast environment?
- A. To route traffic from source to receiver a source tree uses a link-state routing protocol and a shared tree uses a distance-vector routing protocol.
- B. A source tree has its root at the source, and a shared tree has its root at a designated rendezvous point.
- C. To stream multicast from source to receiver, a source tree uses PIM-SM and a shared tree uses PIM-DM.
- D. Source trees are the default type for bidirectional PIM, and PIM-DM uses shared trees by default.
Show answer and explanation ▾
Correct answer: B
A source tree is rooted at the multicast source and uses the shortest path to receivers. A shared tree is rooted at a rendezvous point and all sources send through it.
Why the other options are wrong:
- A. Both tree types are built by PIM and do not depend on link-state or distance-vector protocols.
- C. Both tree types can exist in PIM sparse mode, and PIM-DM does not build shared trees.
- D. Bidirectional PIM uses shared trees, and PIM-DM builds source trees.
Question 37
Which two differences should be considered when deciding whether to implement routing policies or route maps? (Choose two.)
- A. Sequences are added after implementing a route map, but routing policies must be reconfigured when change is needed
- B. Route maps are supported in Cisco IOS Software and routing policies are supported in Cisco IOS XR Software
- C. Route maps are implemented using hierarchical policies, but routing policies must be implemented sequentially
- D. Route maps require an explicit deny at the end of the sequence, but routing policies have an implicit deny at the end of the program
- E. Route policies require sequence numbers, but route maps are implemented without sequencing
Show answer and explanation ▾
Correct answer: A, B
Route maps run on IOS and let sequences be added later, while routing policies run on IOS XR and must be reconfigured when changes are needed. Those are real differences to weigh.
Why the other options are wrong:
- C. Route maps are sequence based and are not built from hierarchical policies.
- D. Route maps also end with an implicit deny, so this is not a difference between them.
- E. Route maps do use sequence numbers, and route policies are not defined by them.
Question 38
Which expression, when used with the as-path-set command, matches the AS path attribute of the route?
- A. Length
- B. dfa-regex
- C. ios-regex
- D. neighbor-is
Show answer and explanation ▾
Correct answer: C
The as-path-set command matches AS path attributes with ios-regex, which uses the same regular expression syntax as Cisco IOS. This lets the set match the route's AS path.
Why the other options are wrong:
- A. Length is a match on path length and is not an expression type for the set.
- B. dfa-regex is not the option that applies Cisco IOS regular expression syntax to the AS path, which is what ios-regex provides.
- D. neighbor-is is a match on the neighboring AS and is not an expression type for the set.
Question 39
Which keyword is used with the match route-type command to redistribute the external BGP and IGP routes using route map?
- A. match route-type type-1
- B. match route-type nssa-external
- C. match route-type type-2
- D. match route-type external
Show answer and explanation ▾
Correct answer: D
The external keyword with match route-type matches external routes, so both external BGP and IGP routes are selected for redistribution through the route map.
Why the other options are wrong:
- A. Type-1 matches only OSPF external type 1 routes.
- B. Nssa-external matches only OSPF NSSA external routes.
- C. Type-2 matches only OSPF external type 2 routes.
Question 40
An engineer is working to implement segment routing protocol on the customer’s core network.
Which step should the engineer take before the segment routing is enabled and is running with BGP?
- A. Segment routing must be configured with EIGRP
- B. Segment routing must be configured with ISIS
- C. MPLS must be configured
- D. Explicit-null must be configured for all neighbors
Show answer and explanation ▾
Correct answer: C
Segment routing with BGP uses the MPLS data plane, so MPLS must be configured before segment routing is enabled. The segment identifiers are carried as MPLS labels.
Why the other options are wrong:
- A. Segment routing is not tied to EIGRP.
- B. Segment routing can run with IS-IS but IS-IS is not a required step before enabling it with BGP.
- D. Explicit-null is an optional label setting and not a prerequisite for enabling segment routing.
Get the complete 300-510 bank
These 40 questions are roughly 15% of the bank. The full pack has 264 real exam questions, each with the same depth of explanation, plus a questions-only PDF for timed practice and free updates forever.
View the full Cisco 300-510 SPRI question bank →
About the 300-510 exam
These 40 Cisco 300-510 SPRI questions are free here. The free sample PDF has 107.