HSRP and VRRP Election Practice
Practise how a first hop redundancy group picks its gateway: the HSRP active router and the VRRP Master. Each problem gives the routers, their priority and preempt setting and four steps (starts, failures, tracked uplinks). You tap the router that is active or Master at the end, and Check my answer names your slip, such as a takeover without preempt.
Exam practice
First hop redundancy protocols are topic 3.5 of the CCNA 200-301 exam, topic 3.3.c of ENCOR 350-401 (Configure first hop redundancy protocols, such as HSRP, VRRP) and topic 1.1.d of DCCOR 350-601. Start with the free real exam questions, then get the full pack.
HSRP and VRRP FAQ
How is the HSRP active router elected?
By priority: the router with the numerically higher priority wins, and with equal priority the router with the higher IP address wins. If no priority is configured, it uses the default of 100. With more than two routers in the group, the next one in that order is the standby router, and the standby router takes over when the active router fails.
Is preempt on by default in HSRP and VRRP?
No for HSRP, yes for VRRP. In HSRP a router takes over from a working active router only when standby preempt is configured on it; Cisco: if preempt is not configured, it cannot take over. In VRRP, RFC 5798 sets Preempt_Mode to True by default. In the drill, default means nothing was set, so read it as off for HSRP and on for VRRP.
Why does a router with a higher HSRP priority not become active?
Because preempt is not configured on it. Cisco's example: when standby preempt is not configured on R2, R2 does not take over the active role even though its priority 100 is higher than R1 effective priority 95, and R1 remains active until it fails. The same happens when a higher priority router starts after another router is already active.
What does interface tracking do in HSRP?
When a tracked interface goes down, the router lowers its priority by the decrement, 10 by default. Another router with a higher priority then becomes active only if it has preempt. When the interface comes back, the priority returns to the configured value, and the router takes the active role back only if it has preempt too.
What is the VRRP address owner?
The router whose own interface address is the virtual IP. Its priority must be 255, and backups use 1 to 254, with 100 as the default. The owner always preempts, whatever its Preempt_Mode, so it becomes Master as soon as it starts up.
Which VRRP router becomes Master when the Master fails?
The Backup with the highest priority. Each Backup waits Master_Down_Interval, and the Skew_Time part of that wait is shorter for a higher priority, so the highest priority Backup takes over first. The same is why the highest priority router becomes Master when the routers start together.
What does the drill leave out?
Anything the pages under Sources do not settle. In HSRP that means a takeover between two routers with the same priority, so no problem ever needs one. It also leaves out preempt delay, timers, HSRP versions and VRRP tracking, and every VRRP problem uses different priorities.
Sources
- IETF, RFC 2281, Cisco Hot Standby Router Protocol (HSRP): the numerically higher priority wins, equal priority goes to the higher IP address, preemption only when configured, and the state table (the standby router becomes active when the active router fails).
- Cisco, Review Hot Standby Router Protocol (HSRP) FAQ (Document 9281): default priority 100, equal priority and the highest IP address, the standby router in groups of more than two, tracking by 10 by default, and why a router needs preempt.
- Cisco, Use HSRP Preempt and Track Commands (Document 13780): the R1 105 and R2 100 example, R1 tracked down to 95, R2 taking over only with standby preempt, and R1 returning after the tracked object recovers.
- IETF, RFC 5798, Virtual Router Redundancy Protocol (VRRP) Version 3: owner priority 255, backups 1 to 254 with 100 by default, Preempt_Mode True by default, the owner always preempts, the highest priority Backup becomes Master, Skew_Time.
- Cisco exam topics: CCNA 200-301 v1.1 (3.5), ENCOR 350-401 v1.2 (3.3.c and 1.1.b) and DCCOR 350-601 v1.2 (1.1.d).
- Checked 21 November 2026: the drill reproduces the cases these pages describe (Cisco's 105 and 100 tracking example with and without preempt, the equal priority rule, the VRRP owner and Preempt_Mode rules). It was tested on 30,100 generated problems against a separate Python re-solver that simulates the RFC 2281 and RFC 5798 state machines. This is an independent practice tool, not made or endorsed by Cisco or the IETF.
Checked 21 November 2026 against RFC 2281 (HSRP), RFC 5798 (VRRP version 3) and Cisco's HSRP documents 9281 and 13780.
- DrillOSPF practicePick the DR and BDR, find the router ID and work out the lowest cost path.
- DrillCisco ACL practiceFind the line a packet matches and write standard and extended ACLs.
- DrillSpanning tree practiceFind the root bridge, root ports, designated and blocked ports on new switch topologies.