EIGRP Practice: Metric, Feasible Successor and Variance
Free EIGRP practice for CCNP ENARSI and ENCOR: work out the classic metric, pick the successor and feasible successors, and find the paths variance adds. Check my answer names the slip, such as an RD equal to the FD or the highest bandwidth used instead of the lowest.
Classic EIGRP metric with the default K values (K1 = K3 = 1, K2 = K4 = K5 = 0). Wide metrics are left out. Delays are shown in microseconds, as on the interface.
Practise the exams
EIGRP is ENARSI 300-410 topic 1.9, with loop-free path selection, load balancing and metrics, and ENCOR 350-401 topic 3.2.a compares EIGRP and OSPF path selection, load balancing and metrics. Start with the free real exam questions, then get the full pack.
EIGRP FAQ
How is the EIGRP metric calculated?
With the default K values, metric = 256 × (10,000,000 ÷ the lowest bandwidth on the path in kbps + the total delay in tens of microseconds). Drop the fraction of the bandwidth part before you scale it. Cisco's example: a path with a lowest bandwidth of 56 kbps and a delay of 2200 gives (178571 + 2200) × 256 = 46277376.
Which bandwidth and which delay go into the metric?
The lowest bandwidth of all the outgoing interfaces on the route, in kbps: not the highest, and never a sum. The delay is the other way round: add the delay of every outgoing interface on the route.
Why divide the delay by 10?
The formula uses tens of microseconds, but show interface and show ip eigrp topology give the delay in microseconds. So a serial interface with a delay of 20000 microseconds counts as 2000.
What are the default K values?
K1 = 1, K2 = 0, K3 = 1, K4 = 0 and K5 = 0, so only bandwidth and delay count. With K5 = 0 the reliability part is 1 and drops out. Routers with mismatched K values do not become neighbours.
What is the difference between feasible distance and reported distance?
The reported distance (RD) is a neighbour's own metric to the network, as it advertises it. R1's metric through that neighbour adds R1's link to it. The feasible distance (FD) is R1's best metric to the network, the one through the successor. show ip eigrp topology lists each path as (metric/RD).
What is the feasibility condition?
A neighbour meets it when its RD is less than R1's FD. Less means strictly less, so an RD equal to the FD fails. A neighbour that meets it is a feasible successor: a loop free backup path R1 can use at once if the successor fails.
Is the successor the neighbour with the lowest RD?
No. The successor is the neighbour with the lowest metric through it, and that metric is the FD. The RD is only used to check whether the other neighbours are feasible.
How does EIGRP variance work?
With variance n, R1 also sends traffic over paths with a metric less than n times the FD, but only through feasible successors. Cisco's example: paths with metrics 20, 30 and 45 and variance 2 use the 20 and 30 paths, because the limit is 40. The 45 path has an RD of 25, above the FD of 20, so it is not used even with variance 3. The default, variance 1, means equal cost only.
Does the drill use wide metrics?
No. Wide metrics measure throughput and latency in picoseconds, so their numbers are different. Every problem here uses the classic metric with the default K values.
Which exam topics does this cover?
ENARSI 300-410 v1.1 topic 1.9, Troubleshoot EIGRP: 1.9.c loop-free path selections (RD, FD, FC, successor, feasible successor), 1.9.e load balancing (equal and unequal cost) and 1.9.f metrics. ENCOR 350-401 v1.2 topic 3.2.a compares the routing concepts of EIGRP and OSPF, including load balancing, path selection and metrics.
Sources
- IETF, RFC 7868, Cisco's Enhanced Interior Gateway Routing Protocol (EIGRP): section 2 (Feasibility Condition: the neighbour's RD is less than this router's FD; Feasible Successor; Successor), 3.3 (the Feasibility Condition), 5.5 (default K values K1 = K3 = 1, K2 = K4 = K5 = 0), 5.6.1.1 (the classic composite metric, lowest bandwidth, sum of delays in tens of microseconds, truncate before scaling, the 10 Mbps Ethernet example) and 5.6.1.2 (default interface bandwidths and delays).
- Cisco, Enhanced Interior Gateway Routing Protocol (Document 16406, updated 31 August 2023): EIGRP Metrics (the scaling formulas, delay in tens of microseconds, round down, the 46277376 and 20307200 worked example), Feasible Distance, Reported Distance, and Feasible Successor (the figure 3 and figure 4 examples, and an RD equal to the FD not being a feasible successor) and Load Balance (the variance multiplier example).
- Cisco, How Does Unequal Cost Path Load Balancing (Variance) Work in IGRP and EIGRP? (Document 13677): routes with a metric less than variance times the minimum metric, only through feasible successors, and the worked example.
- Cisco exam topics: 300-410 ENARSI v1.1 (1.9 Troubleshoot EIGRP: 1.9.c, 1.9.e, 1.9.f) and 350-401 ENCOR v1.2 (3.2.a).
- Checked 20 November 2026. The tool's own approach: problems are generated, R1 reaches one LAN through two to four neighbours, each neighbour reaches the LAN over one link, the network is stable (so the FD is the best metric), and no two paths ever have the same metric. Cisco's two notes word the variance boundary differently, so no path is ever given a metric of exactly variance times the FD. An independent Python re-solver agreed with the drill on 6,000 generated problems, and the drill reproduces the worked examples in RFC 7868 and Cisco documents 16406 and 13677.
Checked 20 November 2026 against RFC 7868, Cisco's EIGRP tech notes 16406 and 13677, and the ENARSI and ENCOR exam topics.
- DrillOSPF practicePick the DR and BDR, find the router ID and work out the lowest cost path.
- DrillRoute selection practicePick the route a router uses by longest prefix, administrative distance and metric, in Cisco IOS or Junos format.
- DrillCisco ACL practiceFind the line a packet matches and write standard and extended ACLs.