Versa Networks VNX301 Practice Questions with Explanations

Free Versa Networks VNX301 practice questions. 11 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.

VNX301 practice questions

Question 1

On an HA active-active deployment, one device has two WAN networks (INET-1 and MPLS-1) and its peer also has two WAN networks (INET-2 and MPLS-2).

In this scenario, how many sub-interfaces will be created on the cross-connect link between the devices by an HA active-active workflow?

  • A. 2
  • B. 1
  • C. 3
  • D. 4
Show answer and explanation ▾

Correct answer: D

The workflow creates a sub-interface on the cross-connect for each WAN network on both devices, which here is 2 plus 2, so 4.

Why the other options are wrong:

  • A. 2 counts only one device's WAN networks.
  • B. 1 does not cover each WAN network.
  • C. 3 misses one of the four WAN networks.

Question 2

What are three roles that VOS performs? (Choose three.)

  • A. uCPE Platform
  • B. Controller
  • C. Zookeeper Arbiter Node
  • D. Log Collector
  • E. SD-Branch
Show answer and explanation ▾

Correct answer: A, B, E

A VOS device can be configured to act as an SD-WAN Controller, as an SD-Branch and as a uCPE platform, alongside the gateway, hub and SD-Router roles. The same VOS software takes on each of these roles through configuration.

Why the other options are wrong:

  • C. The arbiter is a node role in a Versa Director cluster, not a role of a VOS device.
  • D. Log collection is a function of Versa Analytics nodes, which receive and store the logs that VOS devices send.

Question 3

You are configuring the BGP routing protocol between a Versa Secure SD-WAN CPE (AS number 64514) and two upstream Service Providers: SP1 (AS number 64515) and SP2 (AS number 64519). You want to prefer BGP routes learned from AS 64515 over routes leaned from AS 64519.

Which BGP path attributes would be used to accomplished this task?

  • A. the BGP MULTI-EXIT_DISC path attribute
  • B. the BGP ORIGIN path attribute
  • C. the BGP LOCAL_PREF path attribute
  • D. the BGP NEXT_HOP path attribute
Show answer and explanation ▾

Correct answer: C

LOCAL_PREF is set on inbound routes and the highest value wins, so you give SP1 routes a higher value.

Why the other options are wrong:

  • A. MED is advertised to neighbors to influence how they send traffic to you.
  • B. ORIGIN is rarely used to steer traffic this way.
  • D. NEXT_HOP gives the next router and does not rank routes.

Question 4

A router with a BGP autonomous system number of 4200000001 is peered with another router with a BGP autonomous system number of 65533.

The BGP session will be established between the router’s loopback interfaces.

In this scenario, which two statements are true? (Choose two.)

  • A. The BGP session must be a multihop session.
  • B. The first router’s BGP AS is wrong because the maximum permitted value is 65535.
  • C. The routers are considered eBGP neighbors.
  • D. The routers are considered iBGP neighbors.
Show answer and explanation ▾

Correct answer: A, C

The two AS numbers differ, so the peers are eBGP neighbors, and eBGP between loopbacks is not directly connected, so it needs multihop.

Why the other options are wrong:

  • B. 4-byte AS numbers up to 4294967295 are valid.
  • D. iBGP needs both routers in the same AS.

Question 5

What are three spoke group types in Versa Workflows? (Choose three.)

  • A. Spoke-To-Spoke-via-Hub
  • B. Spoke-to-Spoke-Only
  • C. Spoke-to-Hub-Only
  • D. Spoke-To-Spoke-Direct
  • E. Spoke-To-Hub-via-Spoke
Show answer and explanation ▾

Correct answer: A, C, D

Versa Workflows offer the spoke group types Spoke to Hub Only, Spoke to Spoke via Hub and Spoke to Spoke Direct. They decide whether spokes reach only the hub, reach each other through the hub, or reach each other directly.

Why the other options are wrong:

  • B. Spoke-to-Spoke-Only is not a spoke group type in Workflows, since every spoke group is tied to a hub.
  • E. Spoke-To-Hub-via-Spoke is not a spoke group type in Workflows.

Question 6

As an administrator, you are migrating your legacy WAN to Versa Secure SD-WAN without changing the underlay network. You need to ensure that during the migration process, legacy WAN sites are allowed to communicate to SD-WAN branches.

Which two steps should be implemented to accomplish this task? (Choose two.)

  • A. Apply the Spoke-to-Spoke-Direct topology for the SD-WAN branches.
  • B. Using workflows, configure the Gateway option in the hub template for the underlay links.
  • C. Configure BGP on the hub underlay links to advertise and receive the prefixes.
  • D. Configure an SD-WAN traffic steering policy to advertise the SD-WAN routes.
Show answer and explanation ▾

Correct answer: B, C

The hub acts as the gateway between the two networks during migration. The Gateway option in the hub workflow template lets the hub exchange routes between the SD-WAN overlay and the underlay, and BGP on the hub underlay links advertises the SD-WAN prefixes to the legacy WAN and receives the legacy prefixes.

Why the other options are wrong:

  • A. The topology used among SD-WAN branches does not give legacy sites a path to them.
  • D. A traffic steering policy selects paths for traffic, it does not advertise routes.

Question 7

Which statement is correct about full-mesh SD-WAN networks?

  • A. Full mesh networks require extensive manual configuration by the user.
  • B. Full mesh networks can increase the SLA probes on the network and may require additional configuration to reduce the link utilization by probes.
  • C. Full mesh networks still require a hub so that it can relay control plane information.
  • D. Full mesh networks still require you to configure a spoke group to determine which branches can communicate with each other.
Show answer and explanation ▾

Correct answer: B

In a full mesh every branch monitors its paths to every other branch, so the number of SLA probes grows quickly with the number of sites. Probe settings may need tuning so that the probes do not use too much link capacity.

Why the other options are wrong:

  • A. The tunnels of a full mesh are built automatically, without extensive manual configuration.
  • C. Control plane information is relayed by the Controller, so a hub is not needed for that.
  • D. Spoke groups belong to hub and spoke topologies and are not needed for a full mesh.

Question 8

You are asked to ensure symmetric traffic flows between two SD-WAN branches.

Which feature should be enabled to achieve this objective?

  • A. Symmetric Forwarding
  • B. Symmetric Routing
  • C. Equal Cost Multi path
  • D. Packet Striping
Show answer and explanation ▾

Correct answer: B

Symmetric routing means both directions of a flow between the two branches follow the same path, so the return traffic comes back the way the forward traffic went.

Why the other options are wrong:

  • A. Symmetric Forwarding is a forwarding profile setting that is already on by default, so it is not the feature to turn on here.
  • C. Equal cost multipath spreads traffic over several paths and does not tie the return traffic to the forward path.
  • D. Packet striping spreads the packets of a flow across several links, which does not make the flow symmetric.

Question 9

You want to rate-limit a tenant to 10 Mbps.

In this scenario, which statement is correct?

  • A. Configure a QoS profile with a peak rate 10 Mbps.
  • B. Configure the shaping rate on the WAN link to 10 Mbps.
  • C. Configure a QoS policy that matches the LAN zone as the source and the WAN zone as the destination.
  • D. Click Organization under the Organization -> Limits menu and set the peak rate to Mbps.
Show answer and explanation ▾

Correct answer: D

A limit for a whole tenant is set at the organization level. The organization limits hold a peak rate that applies to all traffic of that tenant, which is what a 10 Mbps tenant limit needs.

Why the other options are wrong:

  • A. A QoS profile limits only the traffic that a QoS policy rule sends to it, not the tenant as a whole.
  • B. Shaping the WAN link limits everything on that link, not one tenant.
  • C. A zone-based QoS policy rule only classifies matching traffic and does not set a limit for the tenant.

Question 10

An SD-WAN administrator is asked to enforce ingress Policing for video traffic.

Which action would be used in this process?

  • A. Configure Ingress Policing limits in a Drop Profile.
  • B. Configure Ingress Policing limits in a QoS Profile.
  • C. Configure Ingress Policing limits in a Scheduler.
  • D. Configure Ingress Policing limits in a QoS Policy.
Show answer and explanation ▾

Correct answer: B

Policing limits such as the peak rate and burst size are set in a QoS profile. A QoS policy rule then matches the video traffic and applies that profile to it.

Why the other options are wrong:

  • A. A drop profile controls how packets are dropped from a queue during congestion, not ingress policing.
  • C. A scheduler controls how egress queues are served, not ingress policing.
  • D. A QoS policy rule matches the traffic and points to a QoS profile, the limits themselves are not set in the policy.

Question 11

You configured Direct Internet Access on your Versa branches using the workflow template.

Which statement is true in this scenario?

  • A. You must define a CGNAT address pool, rule, and associate the rule with the Internet-facing network.
  • B. You must define a CGNAT address pool, rule, and associate the rule to the LAN interface.
  • C. DIA configured in a workflow automatically creates a CGNAT pool, rule, and associates it with the Internet-facing network.
  • D. CGNAT is not required when you configure DIA services.
Show answer and explanation ▾

Correct answer: C

When Direct Internet Access is enabled in the workflow template, the workflow creates the CGNAT pool and rule itself and ties them to the Internet-facing network, so LAN traffic is translated on its way out without manual NAT configuration.

Why the other options are wrong:

  • A. The workflow builds the CGNAT pool and rule, so they do not have to be defined by hand.
  • B. The CGNAT rule is not defined by hand and is not tied to the LAN interface.
  • D. DIA traffic leaves through the Internet-facing network with source NAT, so CGNAT is part of the DIA configuration.

That was 11 of 47.

The full Versa Networks VNX301 pack has all 47 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.

Get the full pack

Not ready yet? Get the first 19 free as one PDF by email. Get the Half Pack →

About the VNX301 exam

These 11 Versa Networks VNX301 questions are free here. The free PDF has 19, free by email.

They are drawn from the same bank as the full VNX301 pack, which has 47 questions in total.

Back to blog