Nokia 4A0-205 Practice Questions with Explanations
Free Nokia 4A0-205 practice questions. 24 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.
4A0-205 practice questions
Question 1
What is the definition of OSNR?
- A. The OSNR is defined as the ratio between the transmitted optical power and the received optical power over 1 km of fiber, including both signal and optical noise.
- B. The OSNR is the ratio between the optical output signal power and the optical input signal power of the device being analyzed.
- C. The OSNR is defined as the ratio between the average optical signal power and the average optical noise power over a specific spectral bandwidth.
- D. The OSNR is defined as the ratio between the optical signal power (including noise) and the optical noise power over a specific spectral bandwidth.
Show answer and explanation ▾
Correct answer: C
OSNR compares how strong the signal is with how strong the noise is, measured over a stated bandwidth. A higher ratio means a cleaner signal.
Why the other options are wrong:
- A. That describes loss over a length of fiber, not signal against noise.
- B. Output power over input power is gain, not OSNR.
- D. The signal in the ratio should not include the noise.
Question 2
Which of the following are the main reasons for fiber attenuation?
- A. Refraction and reflection
- B. Scattering and absorption
- C. Chromatic dispersion (CD) and polarization mode dispersion (PMD)
- D. Small channel spacing
Show answer and explanation ▾
Correct answer: B
Light loses power in fiber mainly because the glass scatters some of it and impurities absorb some of it.
Why the other options are wrong:
- A. Refraction and reflection are not the main causes of loss along the fiber.
- C. Dispersion spreads the pulse in time but is not what reduces its power.
- D. Channel spacing affects crosstalk between channels, not fiber attenuation.
Question 3
What is the meaning of first, second, and third window in the optical fiber propagation context?
- A. These windows correspond to three different minimum and maximum optical power levels used for optical transmission.
- B. These windows are three different wavelength intervals where the WDM optical transmission occurs.
- C. These three windows are three different angles of incidence of the light injected by the laser into the fiber.
- D. Different optical transmission windows correspond to different safety requirements and rules for the related lasers operating with these windows.
Show answer and explanation ▾
Correct answer: B
The windows are wavelength bands, around 850, 1300 and 1550 nm, where fiber loss is low enough for transmission.
Why the other options are wrong:
- A. The windows are defined by wavelength, not power level.
- C. They are not angles of incidence.
- D. They are not defined by laser safety rules.
Question 4
In which window(s) does the attenuation reach its minimum peak?
- A. First window (850 nm)
- B. Second window (1300 nm)
- C. Third window (1550 nm)
- D. Both first and second windows
Show answer and explanation ▾
Correct answer: C
Silica fiber loses the least light around 1550 nm, which is why the third window is used for long-distance links.
Why the other options are wrong:
- A. 850 nm has the highest loss of the three windows.
- B. 1300 nm has lower loss than 850 nm but more than 1550 nm.
- D. Neither of those two windows has the lowest attenuation.
Question 5
Which of the following statements is true about chromatic dispersion (CD)?
- A. Different channels have different bandwidth and this causes different CD performances.
- B. The fiber attenuation changes along the fiber, and when the light crosses these differences the CD takes place.
- C. Different wavelengths propagate at different speeds within the same media and therefore different colors travel in the fiber with different speed.
- D. The fiber attenuation introduces inter-channel interference.
Show answer and explanation ▾
Correct answer: C
Chromatic dispersion happens because each wavelength travels at a slightly different speed in glass, so a pulse made of several wavelengths spreads out.
Why the other options are wrong:
- A. CD comes from wavelength-dependent speed, not from channels having different bandwidth.
- B. Attenuation changes do not cause chromatic dispersion.
- D. Attenuation does not cause inter-channel interference, and that is not what CD is.
Question 6
How does a Raman pump work in the 1830 specific implementation?
- A. The amplification is done simultaneously for all channels as they enter the board.
- B. As the incoming signal power increase, the gain of the amplifier is reduced.
- C. The pump light travels in the same direction of the signal, amplifying it while it flows in the fiber towards the following node.
- D. The pump light travels in the opposite direction of the signal to be amplified, amplifying it while it arrives from the adjacent node.
Show answer and explanation ▾
Correct answer: D
The Raman pump is counter-propagating. Pump light is launched into the line fiber against the direction of the signal, so the transmission fiber itself becomes the gain medium and the signal is amplified as it arrives from the adjacent node.
Why the other options are wrong:
- A. Raman gain is distributed along the line fiber, not applied in a single stage as channels enter the board.
- B. This describes gain behavior under rising input power, not how the Raman pump works.
- C. This describes a co-propagating pump, which is not the arrangement used here.
Question 7
WDM allows transmission systems to:
- A. Transport multiple signals transparently, onto several wavelengths, all together over one single fiber
- B. Increase the bit rate of each client signal by spreading it over multiple wavelengths
- C. Share a single signal among multiple fibers doing load balancing, and thus increasing the reliability of the optical transmission
- D. Allocate different signals to different time slots
Show answer and explanation ▾
Correct answer: A
Wavelength division multiplexing assigns each client signal to its own wavelength and combines all the wavelengths onto one fiber. Each signal is carried transparently, so the capacity of a single fiber is multiplied without changing the client signals.
Why the other options are wrong:
- B. WDM does not raise the bit rate of a client signal by spreading it over several wavelengths.
- C. WDM combines many signals on one fiber; it does not split one signal across several fibers.
- D. Allocating signals to time slots is time division multiplexing, not WDM.
Question 8
Which of the following sentence about FlexGrid is false?
- A. FlexGrid allows a more efficient channel spacing.
- B. Channels in FlexGrid systems are allocated with a granularity of 27.5 GHz.
- C. FlexGrid systems use specific sets of boards. Old generation WDM systems need to be upgraded to support FlexGrid.
- D. The FlexGrid is currently standardized by ITU-T.
Show answer and explanation ▾
Correct answer: B
The flexible grid defined in ITU-T G.694.1 allocates channel width in multiples of 12.5 GHz, with central frequencies on a 6.25 GHz raster. A granularity of 27.5 GHz does not exist, so this is the false sentence.
Why the other options are wrong:
- A. This sentence is true: the flexible grid sizes each channel to its needs, which uses spectrum more efficiently.
- C. This sentence is true: flexible grid operation needs hardware built for it.
- D. This sentence is true: ITU-T has standardized the flexible grid in G.694.1.
Question 9
What is a degree-1 node?
- A. A node with only one direction and therefore a terminal node
- B. A node with only one express channel and therefore made of two sides
- C. A node with only east and west sides without directions towards north and south
- D. A node with one direction only and therefore used as In-Line-Amplifier (ILA)
Show answer and explanation ▾
Correct answer: A
The degree of a node is the number of line directions it has. A degree-1 node has a single direction, so all traffic is added and dropped there and it acts as a terminal node.
Why the other options are wrong:
- B. The degree counts line directions, not express channels, and a two-sided node is degree 2.
- C. A node with east and west sides has two directions, so it is degree 2.
- D. An in-line amplifier sits between two spans and does not terminate traffic.
Question 10
With reference to trails and services, which of the following sentences is correct?
- A. Trails are transported over services; that is, trails are clients with respect to services.
- B. A trail can interconnect three ports, while a service always two.
- C. Services are transported over trails; that is, services are clients with respect to trails.
- D. A service is always associated to a single wavelength, while a trail can involve multiple wavelengths.
Show answer and explanation ▾
Correct answer: C
A trail is the server layer connection and a service is the client carried over it. Services therefore ride on trails, which makes services clients with respect to trails.
Why the other options are wrong:
- A. This reverses the relationship: trails are the server layer, not the client.
- B. The difference between a trail and a service is not the number of ports each can interconnect.
- D. A service is not defined as always tied to a single wavelength.
Question 11
What is a trail?
- A. An entity to encapsulate a low order signal into a high order container
- B. A transparent transport of a client signal
- C. A link between end points to increase the power budget of the optical link
- D. A physical link between two optical amplifiers
Show answer and explanation ▾
Correct answer: B
A trail carries a client signal transparently between its end points. It is the transport entity that services use, and it delivers the client signal unchanged from one end to the other.
Why the other options are wrong:
- A. Encapsulating a low order signal into a high order container is mapping, not a trail.
- C. A trail is not a means of increasing the power budget of a link.
- D. A physical link between two amplifiers is a fiber span, not a trail.
Question 12
Which use case is most suitable for the deployment of a star topology?
- A. Access networks, for collecting traffic towards the main central node
- B. ASON networks, to protect traffic via GMPLS protocols
- C. Backbone networks, for supporting protection routes
- D. SNCP-protected links
Show answer and explanation ▾
Correct answer: A
In a star topology every outer node connects to one central node. That suits access networks, where traffic from many sites is collected and handed to a main hub.
Why the other options are wrong:
- B. GMPLS restoration needs alternative routes, which a star does not offer.
- C. Backbone protection routes need a mesh or ring, not a star with a single path to each node.
- D. SNCP protection needs two diverse paths, which a star does not provide.
Question 13
What is the metro area network?
- A. The metro area network is that portion of network that passes through a city to provide connections to several customers.
- B. The metro area network is located between access and core domains.
- C. The metro area network is made of OCS/SWDM nodes only, as no pure photonic nodes are used here.
- D. The metro area network is located in between two access area networks and made of photonic nodes only (no OCS/SWDM nodes are used there).
Show answer and explanation ▾
Correct answer: A
A metro area network covers a city. It runs through the metropolitan area and connects many customer sites there, which is what defines it.
Why the other options are wrong:
- B. Its position relative to other domains does not define what the metro network is or does.
- C. Metro networks are not restricted to OCS/SWDM nodes.
- D. Metro networks are not restricted to photonic nodes, and they do not sit between two access networks.
Question 14
A user needs to check for interface details against the line 1 port of an 11STAR1A card equipped in slot 17.
Which of the following commands is the correct one?
- A. show interface 11star1a 1/17/L1 detail
- B. config card 11star1a interface 1/17 detail
- C. 11star1a 1/17 port-detail
- D. config interface detail 1/17/L1
Show answer and explanation ▾
Correct answer: A
Interface details are read with a show command that names the card type and the port as shelf/slot/port. For line port 1 of the card in slot 17 of shelf 1, that is show interface 11star1a 1/17/L1 detail.
Why the other options are wrong:
- B. A config command changes settings; it is not the command that displays interface details.
- C. This is not a valid command, and it does not identify the line port.
- D. This config command does not name the card type and is not the way to display interface details.
Question 15
What is the OAMP LAN interface?
- A. It is an RJ-45 interface (a common Ethernet port) used for cascading 1830 PSS nodes (e.g., external shelves)
- B. It is an RJ-45 interface (a common Ethernet port) that has to be configured with an IP address for node reachability and management
- C. It is an RJ-45 interface (a common Ethernet port) used to connect one or more client ports (e.g., 1 Gb/s or legacy 100 Mbit/s client flows)
- D. It is an RJ-45 interface (a common Ethernet port) used to export active alarms to an external device, typically equipped with several LEDs
Show answer and explanation ▾
Correct answer: B
OAMP stands for operations, administration, maintenance and provisioning. The OAMP LAN port is the Ethernet management port of the node, and it is given an IP address so the node can be reached and managed.
Why the other options are wrong:
- A. Cascading shelves is not the purpose of the OAMP port.
- C. The OAMP port carries management traffic, not client traffic.
- D. Exporting alarms to an external LED device is not the purpose of the OAMP port.
Question 16
Which of the following statements is true?
- A. Logs report both active and historical events.
- B. Alarms and conditions report a real time status of the node.
- C. Alarms and conditions report only historical status of the node.
- D. Logs report a real time status of the node.
Show answer and explanation ▾
Correct answer: A
Logs keep a record of events over time. They include events that are still active as well as events that have already cleared, so they show both the current and the past history of the node.
Why the other options are wrong:
- B. Alarm and condition lists are not the record that covers both current and past events.
- C. Alarms and conditions are not limited to historical status.
- D. Logs are a record over time, not only a real time view.
Question 17
Which of the following applications is related to Wavelength Tracker tool?
- A. Collecting logs related to possible issue affecting a wavelength path
- B. Tracking the protection path for a specific wavelength
- C. Tracing the end-to-end wavelength optical power
- D. Correcting errors related to wavelength inconsistencies
Show answer and explanation ▾
Correct answer: C
Wavelength Tracker tags each wavelength so its optical power can be measured at points along the path. This lets the operator trace the power of a wavelength end to end across the network.
Why the other options are wrong:
- A. Wavelength Tracker measures optical power; it is not a log collection tool.
- B. It does not track the protection path of a wavelength.
- D. It monitors power and does not correct errors.
Question 18
Is it possible to modify node parameters within the edit EPT menu?
- A. Yes, the user can apply manual change directly from this view
- B. Yes, but the user can modify only the node name and location
- C. No, this view is used to display a close-up view of the node
- D. Yes, the user can apply manual changes but only for non-GMPLS nodes, as the control plane reserves node resources not editable by the user
Show answer and explanation ▾
Correct answer: A
The edit view in EPT is a working view, not a read-only display. The user can apply manual changes to the node directly from it.
Why the other options are wrong:
- B. Editing is not limited to the node name and location.
- C. The view is not only a close-up display; changes can be made in it.
- D. Manual editing is not restricted to nodes without GMPLS.
Question 19
Where can the user set the long-haul WT decoder parameter, when designing a network with EPT?
- A. In the network parameters
- B. In the optimization parameters
- C. In the NE parameters
- D. In the audit menu
Show answer and explanation ▾
Correct answer: B
The long-haul WT decoder setting is one of the optimization parameters in EPT, so it is set there when the design is prepared.
Why the other options are wrong:
- A. The network parameters are not where this setting is found.
- C. The NE parameters are not where this setting is found.
- D. The audit menu checks a design; it is not where this parameter is set.
Question 20
Is it possible to select the fiber type independently for each segment while designing a network in EPT?
- A. Yes, during the link creation through the wizard
- B. No, a unique type is allowed per design for all segments
- C. No, as the fiber type is selected for links only and it’s one for the whole design
- D. Yes, during the segment creation phase or editing
Show answer and explanation ▾
Correct answer: D
EPT sets the fiber type per segment. The user chooses it when the segment is created and can change it later by editing the segment, so different segments can use different fiber types.
Why the other options are wrong:
- A. The fiber type is chosen for the segment, not in the link creation wizard.
- B. A design is not limited to one fiber type for all segments.
- C. The fiber type is not a single setting for the whole design.
Question 21
By using the EPT run design command, are the previously designed elements removed?
- A. Yes, they are but only the first time the command is launched as-for future design phases-the existing packs need to keep the same slotting.
- B. It depends, the user is prompted to choose whether to delete or leave the previously designed elements.
- C. No, the design is always progressive, on top of the previous design.
- D. Yes, although this is not happening in case of GMPLS-enabled nodes because existing slots cannot change as they are controlled by another manager (GMRE).
Show answer and explanation ▾
Correct answer: B
When run design is launched on a network that already has designed elements, EPT asks the user what to do with them. The user chooses whether to delete them or leave them in place.
Why the other options are wrong:
- A. Removal is not automatic on the first run only.
- C. The design is not always progressive; the user can choose to delete earlier elements.
- D. Removal is not automatic, and the behavior does not hinge on GMPLS nodes.
Question 22
What is the purpose of the validate step in the EPT design process?
- A. During this step, the configuration available on the involved network elements is compared with the design provided by EPT.
- B. This step is used to measure optical power performances over an existing network before making changes.
- C. This step is optional and is useful to verify the network element layout before going through the commission step.
- D. During this step, the run design action is triggered for network design consistency check and errors fixing.
Show answer and explanation ▾
Correct answer: D
In the validate step the run design action is launched. EPT checks the network design for consistency and the reported errors are fixed before the design moves on.
Why the other options are wrong:
- A. Validation checks the design itself; it does not compare it with the configuration on live network elements.
- B. Validation does not measure optical power on an existing network.
- C. Validation is not an optional layout check before commissioning.
Question 23
Which statement is correct about the NFM-T network map?
- A. It automatically represents all nodes grouped by the location string assigned during the NE creation.
- B. It represents all supervised nodes grouped by alarm status (with a different color).
- C. It allows context sensitive navigation and represents nodes and related physical connections with different colors, depending on the active alarms.
- D. It allows the graphical visualization of the services deployed in the network with the details of the boards involved in the service.
Show answer and explanation ▾
Correct answer: C
The NFM-T network map shows the nodes and the physical connections between them, colored according to their active alarms. The user can navigate from a map object to related functions for that object.
Why the other options are wrong:
- A. The map does not automatically group nodes by the location string given at NE creation.
- B. The map does not group nodes by alarm status; color shows the alarm state of each object.
- D. The map shows nodes and physical connections, not service details down to the boards involved.
Question 24
Which sentence about NFM-T is correct?
- A. NFM-T fully supports L0, L1, L2 and GMPLS applications and it is mainly focused on 1830 PSS, as well as other older product families
- B. NFM-T fully supports optical and IP nodes
- C. NFM-T is used to design and manage optical networks
- D. NFM-T is used to provision optical services having IP nodes as extremities
Show answer and explanation ▾
Correct answer: C
NFM-T is the network management system for the optical network. It is used to design and manage optical networks from one application.
Why the other options are wrong:
- A. This overstates the scope of NFM-T and is not an accurate description of it.
- B. NFM-T is an optical network manager, not a manager for IP nodes.
- D. NFM-T does not provision services that terminate on IP nodes.
That was 24 of 95.
The full Nokia 4A0-205 pack has all 95 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.
Get the full packNot ready yet? Get the first 24 free as one PDF by email. Get the Half Pack →
About the 4A0-205 exam
These 24 Nokia 4A0-205 questions are free here, and as a free PDF by email.
They are drawn from the same bank as the full 4A0-205 pack, which has 95 questions in total.