Nokia 4A0-116 Practice Questions with Explanations
Free Nokia 4A0-116 practice questions. 14 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.
4A0-116 practice questions
Question 1
Which of the following statements about Multi-Protocol Label Switching networks is FALSE?
- A. MPLS uses a signaling protocol to exchange labels between routers.
- B. An LSR forwards data based on the MPLS labels.
- C. An LSP is a bi-directional tunnel that uses MPLS labels to forward data.
- D. The data is transparently carried from end to end.
Show answer and explanation ▾
Correct answer: C
An LSP is unidirectional, so calling it a bi-directional tunnel is the false statement.
Why the other options are wrong:
- A. True: a signaling protocol exchanges labels between routers.
- B. True: an LSR forwards on the MPLS labels.
- D. True: the data is carried transparently from end to end.
Question 2
Which of the following statements about a Segment Routing SID is FALSE?
- A. A Node-SID is usually associated with a router's system interface.
- B. Adjacency-SID values are taken from the SRGB configured for the routing protocol.
- C. A Prefix-SID can be configured directly as a label value or indirectly as an index.
- D. An Adjacency-SID does not have to be configured.
Show answer and explanation ▾
Correct answer: B
A router advertises its local Node-SID as a local SRGB and an index whether it was configured as an index or as a label, so "only if" is false.
Why the other options are wrong:
- A. True: a local Node-SID can be configured directly as an MPLS label.
- C. True: routers do not all need the same SRGB range.
- D. True: a local Node-SID can be configured as an index.
Question 3
Which of the following statements about Segment Routing is FALSE?
- A. No path signaling is required to establish an SR tunnel.
- B. Intermediate routers do not maintain any tunnel information.
- C. A link-state IGP is required to distribute SID information.
- D. For TE-constrained tunnels, each data packet typically carries a single MPLS label to specify the tunnel path.
Show answer and explanation ▾
Correct answer: D
SR paths are defined by a list of segments, so a packet on a TE-constrained tunnel typically carries a stack of labels, not a single label.
Why the other options are wrong:
- A. True: SR needs no path signaling to set up a tunnel.
- B. True: intermediate routers hold no per-tunnel state.
- C. True: a link-state IGP distributes the SID information.
Question 4
Which of the following statements about a Segment Routing SID is FALSE?
- A. A local Node-SID can be configured directly as an MPLS label.
- B. A router advertises its local Node-SID as a local SRGB and an index only if it is configured as an index.
- C. All routers do NOT need to have the same SRGB range configured.
- D. A local Node-SID can be configured as an index.
Show answer and explanation ▾
Correct answer: C
A prefix SID index only maps to the same meaning everywhere when the routers share the same index range, so all routers in the network are expected to configure and advertise the same SRGB range.
Why the other options are wrong:
- A. This statement is true: a Node-SID can be entered as an absolute MPLS label.
- B. A Node-SID is advertised as an index relative to the SRGB.
- D. This statement is true: a Node-SID can be entered as an index into the SRGB.
Question 5
When OSPF is used to support Segment Routing, the first byte of the link-state ID associated with each of the opaque LSAs indicates the type of information being advertised.
Which of the following associations between the first-byte value and its meaning is FALSE?
- A. Value 1 - Traffic Engineering
- B. Value 4 - Router Info
- C. Value 7 - SRGB Range
- D. Value 8 - Extended Link Info
Show answer and explanation ▾
Correct answer: C
Opaque type 7 identifies the OSPFv2 Extended Prefix LSA, which carries prefix SIDs. The SRGB range is advertised in the Router Information LSA, opaque type 4, so linking value 7 to the SRGB range is the false association.
Why the other options are wrong:
- A. This association is correct: opaque type 1 is the Traffic Engineering LSA.
- B. This association is correct: opaque type 4 is the Router Information LSA.
- D. This association is correct: opaque type 8 is the OSPFv2 Extended Link LSA.
Question 6
Which of the following steps is NOT required when configuring IS-IS to support Segment Routing?
- A. MPLS label range reserved for Segment Routing.
- B. Enable interfaces used for Segment Routing under the MPLS context.
- C. The flooding scope of Segment Routing information.
- D. The Segment Routing Global Block range.
Show answer and explanation ▾
Correct answer: D
With the prefix SID range set to global, the IS-IS instance uses the whole label range already reserved for Segment Routing, so a separate Segment Routing Global Block range does not have to be defined in IS-IS. The reserved label range and the flooding scope of the router capability still have to be set.
Why the other options are wrong:
- A. A label range must be reserved for Segment Routing before it can be enabled in IS-IS.
- B. Interfaces that carry Segment Routing traffic are added to the MPLS context as part of the setup.
- C. The router capability advertisement, with its flooding scope of area or AS, must be set before Segment Routing can be enabled.
Question 7
OSPF type-10 Opaque LSAs can carry different types of advertisements.
What type of advertisement carries a router's local SRGB information?
- A. Extended Prefix Info
- B. Router Info
- C. Extended Link Info
- D. Traffic Engineering Info
Show answer and explanation ▾
Correct answer: B
A router's Segment Routing capabilities, including its SRGB as a SID/Label range, are carried in the Router Information opaque LSA.
Why the other options are wrong:
- A. Extended Prefix opaque LSAs carry prefix SIDs, not the SRGB.
- C. Extended Link opaque LSAs carry adjacency SIDs, not the SRGB.
- D. Traffic Engineering opaque LSAs carry TE link attributes, not the SRGB.
Question 8
Which of the following is not required to be advertised by a router participating in Segment Routing?
- A. Local Node-SID
- B. Adjacency-SIDs
- C. Support for SR-MPLS for IPv4 or IPv6, or SRv6
- D. SRGB when SRv6 is configured
Show answer and explanation ▾
Correct answer: D
The SRGB is an MPLS label block, so it only applies to SR-MPLS. With SRv6 the SIDs are IPv6 addresses taken from a locator, and no SRGB needs to be advertised.
Why the other options are wrong:
- A. A router advertises its Node-SID so that other routers can reach it with Segment Routing.
- B. A router advertises adjacency SIDs for its links.
- C. A router advertises which Segment Routing data plane it supports.
Question 9
Which of the following statements about Segment Routing tunnels is FALSE?
- A. A Segment Routing tunnel defined by a Node-SID uses the shortest IGP Path.
- B. A Segment Routing tunnel can be defined by multiple Node-SIDs.
- C. A Segment Routing tunnel can be defined by a combination of Node-SIDs and Adjacency-SIDs.
- D. For a Segment Routing tunnel, an intermediate router will always forward the packet based on the best IGP path.
Show answer and explanation ▾
Correct answer: D
An intermediate router forwards according to the active segment. When that segment is an Adjacency-SID, the packet is sent out over that specific link even when it is not on the best IGP path, so forwarding does not always follow the best IGP path.
Why the other options are wrong:
- A. This statement is true: a Node-SID segment follows the shortest IGP path to that node.
- B. This statement is true: a tunnel can be a list of several Node-SIDs.
- C. This statement is true: Node-SIDs and Adjacency-SIDs can be combined in one segment list.
Question 10
Which of the following is NOT one of the main goals of traffic engineering?
- A. Utilizing redundant links.
- B. Avoiding potential congestion points in the network.
- C. Defining traffic paths based on various constraints.
- D. Using the shortest possible path through the network to the destination.
Show answer and explanation ▾
Correct answer: A
Traffic engineering steers traffic along paths chosen by constraints so that congestion is avoided and the path taken is still as short as the constraints allow. Making use of redundant links is not one of its main goals.
Why the other options are wrong:
- B. Avoiding potential congestion points is a main goal of traffic engineering.
- C. Defining paths that meet constraints is a main goal of traffic engineering.
- D. Among the paths that meet the constraints, traffic engineering selects the shortest one.
Question 11
Which of the following statements about SR-TE administrative constraints is FALSE?
- A. A strict hop must be adjacent to the previous hop in the list.
- B. The TE metric for a link is by default the same as the IGP metric.
- C. Shared-Risk-Link Groups are only taken into account when calculating the secondary path.
- D. The head-end router may calculate a path that takes into account max hop count and bandwidth constraints.
Show answer and explanation ▾
Correct answer: B
The TE metric is a link attribute of its own, set on the MPLS interface and advertised separately from the IGP metric, so path calculation can use a value that differs from the IGP metric.
Why the other options are wrong:
- A. This statement is true: a strict hop must be directly connected to the previous hop.
- C. This statement is true as written for SRLG handling on the secondary path.
- D. This statement is true as written for the path calculation at the head-end router.
Question 12
A router participating in SR-TE is advertising a value of 0x11 for the admin-group membership of one of its interfaces.
Which of the following statements is TRUE?
- A. The interface belongs to admin group RED, configured with a value of 17.
- B. Theinterface belongs to two different admin groups.
- C. Theinterface belongs to three different admin groups.
- D. Theinterface belongs to four different admin groups.
Show answer and explanation ▾
Correct answer: B
Admin-group membership is advertised as a 32-bit mask in which each set bit is one group. 0x11 is binary 10001, so two bits are set (group values 0 and 4) and the interface belongs to two admin groups.
Why the other options are wrong:
- A. A single group with value 17 would set one bit only, which gives a different mask.
- C. Only two bits are set in 0x11, not three.
- D. Only two bits are set in 0x11, not four.
Question 13
Which of the following statements about enabling and using traffic engineering for Segment Routing is FALSE?
- A. One interface can belong to an admin group and an SRLG group at the same time.
- B. A link attribute has to be assigned to a particular interface under the [/configure router interface] context.
- C. Bandwidth availability as a link attribute cannot be configured.
- D. The interfaces used for SR-TE LSPs have to be added to the MPLS context.
Show answer and explanation ▾
Correct answer: B
Link attributes used for SR-TE, such as admin groups and SRLGs, are applied to the interface in the MPLS context, not in the router interface context.
Why the other options are wrong:
- A. This statement is true: an interface can be in an admin group and an SRLG at once.
- C. This statement is true as written for SR-TE link attributes.
- D. This statement is true: interfaces used by SR-TE LSPs are added to the MPLS context.
Question 14
Which of the following list of SR-TE attributes has to be advertised among routers?
- A. Administrative groups that each link belongs to, TE metric of links, bandwidth availability of each link, SRLG that each link belongs to.
- B. Administrative groups that each link belongs to, TE metric of links, SRLG that each link belongs to.
- C. Administrative groups that each link belongs to, TE metric of links, bandwidth availability of each link, SRLG that each link belongs to, link status up/down.
- D. Administrative groups that each link belongs to, TE metric of links, SRLG that each link belongs to, link status up/down.
Show answer and explanation ▾
Correct answer: C
To compute constrained paths, routers need the full TE view of each link: its admin groups, TE metric, available bandwidth, SRLG membership and whether the link is up or down.
Why the other options are wrong:
- A. This list leaves out the link status.
- B. This list leaves out bandwidth availability and the link status.
- D. This list leaves out bandwidth availability.
That was 14 of 40.
The full Nokia 4A0-116 pack has all 40 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.
Get the full packNot ready yet? Get the first 14 free as one PDF by email. Get the Half Pack →
About the 4A0-116 exam
These 14 Nokia 4A0-116 questions are free here, and as a free PDF by email.
They are drawn from the same bank as the full 4A0-116 pack, which has 40 questions in total.