Juniper JN0-650 JNCIP-ENT Practice Questions with Explanations

Free Juniper JN0-650 JNCIP-ENT practice questions. 25 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.

JN0-650 practice questions

Question 1

Your OSPF network consists of a mix of 1GbE and 10GbE interfaces. By default, all interfaces have the same cost in your OSPF network. You are asked to ensure that the 10GbE interfaces are more preferred when available.

In this scenario, which two statements would accomplish this behavior? (Choose two.)

  • A. You should define the reference bandwidth as 10G, which will assign the 1GbE interfaces a higher cost.
  • B. You should manually assign the interface metric for each 10GbE interface to be higher than the 1GbE interfaces in your OSPF network.
  • C. You should define the reference bandwidth as 1G, which will assign the 1GbE interfaces a higher cost.
  • D. You should manually assign the interface metric for each 1GbE interface to be higher than the 10GbE interfaces in your OSPF network.
Show answer and explanation ▾

Correct answer: A, D

OSPF cost is the reference bandwidth divided by the interface bandwidth. With the default reference bandwidth both speeds end up at the lowest cost, so raising it to 10G gives 1GbE links a higher cost, and setting a higher metric on the 1GbE links by hand has the same effect.

Why the other options are wrong:

  • B. A higher metric on the 10GbE links makes them less preferred, the opposite of the goal.
  • C. A 1G reference bandwidth gives both 1GbE and 10GbE links the minimum cost, so they still tie.

Question 2

You have two multicast receivers connected to the same VLAN. You notice that the switch that they are connected to is forwarding multicast traffic out of all the ports in the same VLAN, instead of just the two ports for the connected multicast receivers.

In this scenario, what would you configure to optimize multicast forwarding?

  • A. promiscuous mode
  • B. spanning tree
  • C. IGMP snooping
  • D. IRB interface
Show answer and explanation ▾

Correct answer: C

IGMP snooping lets the switch learn which ports have receivers that joined a multicast group. It then forwards the group's traffic only to those ports instead of flooding the VLAN.

Why the other options are wrong:

  • A. Promiscuous mode makes a port accept all traffic and would not limit forwarding.
  • B. Spanning tree prevents Layer 2 loops and does not control multicast forwarding.
  • D. An IRB interface gives a VLAN a Layer 3 interface and does not stop flooding.

Question 3

You are implementing an EVPN-VXLAN edge-routed bridging design using Layer 3 gateway operations.

In this scenario, which statement is correct?

  • A. Each distribution switch has unique IP addresses for IRB interfaces; routing protocols run on IRB interfaces.
  • B. Distribution switches share the same anycast IP addresses for IRB interfaces; routing occurs at the distribution layer.
  • C. Only core switches have IRB interfaces; all Layer 3 routing happens in the core.
  • D. IRB interfaces are disabled; all routing happens through external routers only.
Show answer and explanation ▾

Correct answer: B

In edge-routed bridging the Layer 3 gateway sits at the edge switches. Every one of them uses the same anycast gateway address on its IRB interface, so a host's gateway is always local and inter-VLAN routing is done there.

Why the other options are wrong:

  • A. Unique IRB addresses on each switch do not give hosts one shared gateway address.
  • C. Routing only in the core describes a centrally-routed design, not edge-routed.
  • D. IRB interfaces are what provide the gateway in this design, so they are not disabled.

Question 4

Which statement about LLDP and LLDP-MED operations on EX Series devices is correct?

  • A. LLDP only operates on interfaces configured for Layer 2.
  • B. EX Series devices flood LLDP frames across a Layer 2 domain to calculate a network topology.
  • C. EX Series devices support LLDP-MED power negotiation, enabling dynamic allocation of PoE power based on endpoint device needs.
  • D. LLDP-MED focuses on discovering network connectivity devices like routers and switches.
Show answer and explanation ▾

Correct answer: C

LLDP-MED is the media endpoint extension of LLDP. EX Series switches use it to exchange PoE requirements with endpoints such as IP phones, so power can be allocated to what each device needs.

Why the other options are wrong:

  • A. LLDP is not limited to Layer 2 interfaces.
  • B. LLDP frames only travel one hop to the directly connected neighbor and are not flooded across the domain.
  • D. LLDP-MED is aimed at endpoint devices such as phones, not at routers and switches.

Question 5

You are deploying a new campus switching environment using EX Series switches. This new environment includes IP phones requiring Power over Ethernet (PoE) and end-user client PCs attached to a single switch port that will be configured with 802.1X authentication.

Considering the default configuration on an EX Series access switch and the configuration requirements to support this deployment, which two statements are correct? (Choose two.)

  • A. Configuration for the voice VLAN for all relevant access ports must be added.
  • B. Configuration for PoE on all relevant access ports must be added.
  • C. Configuration for LLDP and LLDP-MED on all relevant access ports must be added.
  • D. Configuration for 802.1X on all relevant access ports must be added.
Show answer and explanation ▾

Correct answer: A, D

The factory default configuration of an EX Series access switch already enables PoE on all PoE-capable ports and runs LLDP and LLDP-MED on all interfaces. The voice VLAN and 802.1X authentication are not part of the default configuration, so both must be added on the access ports.

Why the other options are wrong:

  • B. PoE is enabled by default on the PoE-capable ports.
  • C. LLDP and LLDP-MED are enabled by default on the interfaces.

Question 6

Which two statements are correct about multicast routing tables? (Choose two.)

  • A. inet.2 is used when the multi cast forwarding topology differs from unicast forwarding.
  • B. MBGP and IS-IS place routes in inet.1 directly.
  • C. inet.0 is used for RPF checks.
  • D. IS-IS and OSPFv3 place routes in inet.2 directly.
Show answer and explanation ▾

Correct answer: A, C

By default, Junos performs multicast RPF checks against the unicast routes in inet.0. The inet.2 table is used for RPF instead when the multicast topology needs to differ from the unicast forwarding topology.

Why the other options are wrong:

  • B. The inet.1 table is the multicast forwarding cache, and it is not populated directly by MBGP and IS-IS.
  • D. This pairing of protocols is not what populates inet.2 directly.

Question 7

Which two EVPN types advertise an ESI without advertising a MAC address? (Choose two.)

  • A. Type 1
  • B. Type 2
  • C. Type 3
  • D. Type 4
Show answer and explanation ▾

Correct answer: A, D

The Type 1 Ethernet Auto-Discovery route and the Type 4 Ethernet Segment route both carry an Ethernet segment identifier and contain no MAC address field. Type 1 supports aliasing and fast convergence, and Type 4 is used for designated forwarder election.

Why the other options are wrong:

  • B. The Type 2 route is the MAC/IP Advertisement route, so it carries a MAC address.
  • C. The Type 3 Inclusive Multicast Ethernet Tag route does not carry an ESI.

Question 8

Which two statements are correct about EVPN/VXLAN deployments? (Choose two.)

  • A. VNIs are used for encapsulating and de-encapsulating traffic entering and leaving the tunnels.
  • B. VTEPs are used for encapsulating and de-encapsulating traffic entering and leaving the tunnels.
  • C. VTEPs are used to identify broadcast domains within an EVPN/VXLAN environment.
  • D. VNIs are used to identify broadcast domains within an EVPN/VXLAN environment.
Show answer and explanation ▾

Correct answer: B, D

A VXLAN tunnel endpoint (VTEP) adds the VXLAN header to traffic entering a tunnel and removes it from traffic leaving the tunnel. The VXLAN network identifier (VNI) is the 24-bit value that identifies each Layer 2 broadcast domain in the overlay.

Why the other options are wrong:

  • A. A VNI is an identifier, it does not perform encapsulation.
  • C. A VTEP is a tunnel endpoint, broadcast domains are identified by VNIs.

Question 9

Which statement accurately describes the operation of OSPF within the Junos OS?

  • A. OSPF calculates routes using a distance vector algorithm.
  • B. OSPF is used for routing information and neighbor discovery within a single autonomous system (AS).
  • C. OSPF does not automatically advertise directly connected routes.
  • D. OSPF is used for routing information and neighbor discovery between multiple autonomous systems.
Show answer and explanation ▾

Correct answer: B

OSPF is an interior gateway protocol. It discovers neighbors with hello packets and exchanges link-state routing information between routers inside a single autonomous system.

Why the other options are wrong:

  • A. OSPF is a link-state protocol that runs the shortest-path-first algorithm, not a distance vector algorithm.
  • C. This is not the statement that describes how OSPF operates as an interior gateway protocol.
  • D. Routing between autonomous systems is the job of an exterior gateway protocol such as BGP.

Question 10

You run a multivendor switching environment where you have configured VSTP. You have 450 VLANs and notice that some of your VLANs do not function properly.

How should you change the configuration to get all 450 VLANs working?

  • A. Include the force-version stp; statement in your configuration.
  • B. Enable RSTP to handle additional VLANs.
  • C. Set the VLAN max-age to 3600 or more.
  • D. Increase the bridge priority on all VLANs to at least 16k.
Show answer and explanation ▾

Correct answer: B

VSTP runs a separate spanning-tree instance per VLAN and supports a limited number of VLANs, 253 on switches without ELS software. For the VLANs beyond that limit you enable RSTP as well, which protects the additional VLANs with a single instance.

Why the other options are wrong:

  • A. The force-version stp statement makes the protocol run as original 802.1D STP, it does not raise the number of supported VLANs.
  • C. The max-age timer controls how long BPDU information is kept, not how many VLANs are supported.
  • D. Bridge priority influences root bridge election, not the number of supported VLANs.

Question 11

Your router is discarding an EBGP route because the next hop is not directly connected.

Which BGP configuration would you use to override this behavior?

  • A. accept-remote-nexthop
  • B. multihop
  • C. advertise-inactive
  • D. multipath
Show answer and explanation ▾

Correct answer: A

The accept-remote-nexthop statement lets a single-hop EBGP peer accept a route whose next hop is a remote address that is not on the directly connected subnet, instead of discarding it.

Why the other options are wrong:

  • B. Multihop is for EBGP sessions to peers that are not directly connected, not for accepting a remote next hop from a directly connected peer.
  • C. The advertise-inactive statement makes BGP advertise its best route even when that route is not the active route.
  • D. Multipath enables load sharing across equal BGP paths.

Question 12

Which three statements about VSTP are correct? (Choose three.)

  • A. Separate BPDUs are flooded for each VSTP enabled VLAN.
  • B. VSTP is incompatible with RSTP.
  • C. VSTP is enabled by default on EX Series switches.
  • D. VSTP supports up to 253 unique spanning tree topologies.
  • E. A separate spanning tree instance is generated for each VLAN.
Show answer and explanation ▾

Correct answer: A, D, E

VSTP creates a separate spanning-tree instance for every VLAN it is enabled on, and each instance sends its own BPDUs for that VLAN. VSTP supports up to 253 different spanning-tree topologies.

Why the other options are wrong:

  • B. VSTP and RSTP can run at the same time on a switch.
  • C. RSTP, not VSTP, is the spanning-tree protocol in the default configuration of EX Series switches.

Question 13

You must implement EVPN signaling on an EX Series device that is configured with both underlay and overlay networks.

Which network protocol accomplishes this task?

  • A. OSPF underlay network
  • B. IS-IS underlay network
  • C. MPLS overlay network
  • D. EBGP overlay network
Show answer and explanation ▾

Correct answer: D

EVPN is signaled by multiprotocol BGP. The overlay BGP sessions, here EBGP, carry the EVPN address family between the devices, while the underlay only provides IP reachability between loopbacks.

Why the other options are wrong:

  • A. An OSPF underlay provides IP reachability, it does not carry EVPN routes.
  • B. An IS-IS underlay provides IP reachability, it does not carry EVPN routes.
  • C. MPLS is a transport and encapsulation method, not the protocol that signals EVPN.

Question 14

Which two statements are correct about OSPFv2 and OSPFv3? (Choose two.)

  • A. OSPFv2 carries prefix information in LSAs.
  • B. OSPFv3 is processed per subnet.
  • C. OSPFv2 and OSPFv3 require an Area 0.
  • D. OSPFv3 carries flooding scope in LSAs.
Show answer and explanation ▾

Correct answer: A, D

In OSPFv2, the router and network LSAs carry IP prefix information. OSPFv3 moved addressing out of those LSAs and encodes a flooding scope, link-local, area or AS, in the type field of every LSA.

Why the other options are wrong:

  • B. OSPFv3 runs per link, not per subnet.
  • C. A single-area network can use any area ID, the backbone area is only needed to connect multiple areas.

Question 15

You have a P-VLAN that spans multiple switches.

In this scenario, how do you enable communication across the P-VLAN?

  • A. Configure trunk ports with inter-switch-link on the switches.
  • B. Configure trunk ports with private-vlan isolated on the switches.
  • C. Configure trunk ports with private-vlan community on the switches.
  • D. Configure trunk ports with isolated-vlan on the switches.
Show answer and explanation ▾

Correct answer: A

When a private VLAN spans several switches, the trunk ports that connect the switches are configured as inter-switch-link ports. The link then carries the primary VLAN and all of its secondary VLANs while keeping their isolation rules.

Why the other options are wrong:

  • B. That option does not define a trunk that carries the whole private VLAN between switches.
  • C. That option does not define a trunk that carries the whole private VLAN between switches.
  • D. The isolated-vlan setting assigns the tag used for isolated ports, it does not make a trunk carry the whole private VLAN.

Question 16

You are configuring CoS throughout your enterprise network using DSCP. You have configured MF classification on your edge devices and are using BA classifiers throughout the core. You are using the EZQoS template provided on your EX Series switches that are acting as your edge devices. You have loaded the configuration group and applied it to the appropriate interfaces. Classification and scheduling are working properly on your edge devices; however, traffic is not being classified correctly when it reaches your core devices.

In this scenario, which statement is correct about solving this problem?

  • A. You should configure and apply a policer to the edge devices' egress interfaces toward the core.
  • B. You must configure the core devices using the EZQoS template as well.
  • C. You should configure and apply rewrite rules on the edge devices' egress interfaces toward the core.
  • D. You must configure the edge devices to use BA classifiers instead of MF classifiers.
Show answer and explanation ▾

Correct answer: C

Multifield classification on the edge assigns a forwarding class but does not change the DSCP value in the packet. The core uses BA classifiers, which read the DSCP bits, so the edge devices must apply rewrite rules on egress to mark the packets before they reach the core.

Why the other options are wrong:

  • A. A policer limits traffic rate, it does not set the DSCP value the core reads.
  • B. The core devices already classify with BA classifiers, the missing piece is the marking on packets leaving the edge.
  • D. Unmarked traffic arriving at the edge still needs multifield classification.

Question 17

You want to validate a recursive lookup for an EVPN route designation.

Which route table query will accomplish this task?

  • A. inet.2
  • B. default-switch.evpn.0
  • C. inet.3
  • D. vxlan.inet.0
Show answer and explanation ▾

Correct answer: C

BGP resolves the protocol next hop of routes it learns from a remote PE recursively, and inet.3 is the table BGP uses to resolve next hops through tunnels to that PE. Checking inet.3 for the remote loopback confirms the lookup succeeds.

Why the other options are wrong:

  • A. The inet.2 table is used for multicast RPF checks.
  • B. The default-switch.evpn.0 table holds the EVPN routes themselves, not the entries used to resolve their next hops.
  • D. This is not the table queried for this recursive lookup.

Question 18

You are adding a new QFX Series switch to an EVPN-VXLAN IP fabric.

In this scenario, which two statements are correct? (Choose two.)

  • A. The encapsulation vxlan setting is configured under the protocols evpn hierarchy.
  • B. The family vpls signaling address family is configured under the BGP protocol.
  • C. The family evpn signaling address family is configured under the BGP protocol.
  • D. The loopback interface must be advertised using the BGP protocol.
Show answer and explanation ▾

Correct answer: A, C

On a QFX Series switch, encapsulation vxlan is set under protocols evpn so that EVPN uses VXLAN tunnels. The overlay BGP sessions must carry the EVPN address family, which is enabled with family evpn signaling.

Why the other options are wrong:

  • B. The family vpls address family is not used for EVPN.
  • D. The loopback must be reachable in the underlay, but any underlay routing protocol can advertise it.

Question 19

You are deploying a three-stage EVPN environment with VXLAN using EX and QFX Series switches. The leaf devices will perform the gateway services.

Which two statements are correct in this scenario? (Choose two.)

  • A. Only the leaf devices must support VXLAN capabilities.
  • B. The leaf devices will function as VTEPs.
  • C. Both the leaf and spine devices must support VXLAN capabilities.
  • D. The spine devices will function as VTEPs.
Show answer and explanation ▾

Correct answer: A, B

When the leaf devices provide the gateway services, the VXLAN tunnels start and end on the leaf devices, so the leaves are the VTEPs. The spine devices only forward the underlay IP packets, so only the leaf devices need VXLAN support.

Why the other options are wrong:

  • C. The spine devices only route IP packets between leaves and do not need VXLAN support.
  • D. The tunnels terminate on the leaf devices, not on the spines.

Question 20

You have created a private community VLAN called RND. The private community VLAN works fine within switch S1, but traffic in the private RND community VLAN does not reach VLAN members connected to switch S2.

Which statement is correct in this scenario?

  • A. The RND community VLAN needs to have the same 802.1Q tag as its parent VLAN.
  • B. The RND community VLAN needs to have an associated 802.1Q tag associated with it.
  • C. The RND community VLAN needs to be stripped of all 802.1Q tags.
  • D. The RND community VLAN needs to be defined as an isolated VLAN.
Show answer and explanation ▾

Correct answer: B

A secondary VLAN of a private VLAN can work inside one switch without a tag, but to span switches its traffic must be carried on the trunk with its own 802.1Q VLAN ID. Assigning a tag to the RND VLAN lets S2 identify its members.

Why the other options are wrong:

  • A. A secondary VLAN uses its own tag, which differs from the primary VLAN tag.
  • C. Removing tags would leave the trunk with no way to identify RND traffic.
  • D. An isolated VLAN stops its members from talking to each other, which defeats the purpose of RND.

Question 21

Your organization uses 802.1X with a RADIUS server. If the RADIUS server stops responding, you want the fallback action to continue to permit access for devices that currently have authorization but deny any new access attempts.

Which fallback action provides this capability?

  • A. deny
  • B. vlan-name
  • C. permit
  • D. use-cache
Show answer and explanation ▾

Correct answer: D

The use-cache server fail fallback action keeps devices that were already authenticated connected when the RADIUS server times out during reauthentication, while new devices that try to authenticate are denied.

Why the other options are wrong:

  • A. The deny action blocks all devices, including those already authorized.
  • B. The vlan-name action moves devices to a specified VLAN.
  • C. The permit action also lets new devices onto the network.

Question 22

Which two statements are correct when using the no-loss forwarding class? (Choose two.)

  • A. Use the default scheduler map.
  • B. Use forwarding class sets.
  • C. Use priority-based now control.
  • D. Use the default drop profile.
Show answer and explanation ▾

Correct answer: B, C

A no-loss forwarding class depends on priority-based flow control (PFC) to pause the sender for that priority instead of dropping frames. Lossless classes are scheduled through forwarding class sets, which group forwarding classes into priority groups for enhanced transmission selection.

Why the other options are wrong:

  • A. The default scheduler map is not what provides lossless transport for a no-loss forwarding class.
  • D. A default drop profile is not what makes a forwarding class lossless.

Question 23

Which statement accurately describes the role of a multicast RP, specifically when using the PIM sparse mode?

  • A. The RP functions as a central point where multicast sources announce their existence and receivers send join requests to start multicast sessions.
  • B. The RP is primarily used in the PIM dense mode to flood multicast traffic throughout the network periodically.
  • C. The RP is responsible for forwarding all multicast traffic to all interfaces on the network, regardless of receiver interest.
  • D. The RP in the PIM sparse mode eliminates the need for any source-specific multicast (SSM) configurations.
Show answer and explanation ▾

Correct answer: A

In PIM sparse mode the rendezvous point is the meeting place for sources and receivers. First-hop routers register their sources with the RP, and receivers' routers send joins toward the RP to build the shared tree.

Why the other options are wrong:

  • B. Dense mode floods and prunes without an RP.
  • C. Sparse mode forwards traffic only where receivers have joined.
  • D. The RP has no bearing on SSM, which builds source trees without one.

Question 24

You are asked to establish authentication for users connecting to the corporate network. You must ensure that only corporate devices that are identified by MAC addresses are allowed to authenticate and connect. Authentication must be handled by a centralized database.

Which authentication method would you implement in this scenario?

  • A. MAC RADIUS
  • B. captive portal
  • C. single-secure supplicant mode
  • D. single supplicant mode
Show answer and explanation ▾

Correct answer: A

MAC RADIUS authentication sends the MAC address of the connecting device to a RADIUS server, which checks it against its central database. Only devices whose MAC addresses are listed there are allowed onto the network.

Why the other options are wrong:

  • B. Captive portal authenticates users through a web login page, not by device MAC address.
  • C. Single-secure is a supplicant mode that limits a port to one device, not an authentication method.
  • D. Single is a supplicant mode, not a method of authenticating by MAC address.

Question 25

Your Layer 2 network uses 802.1X to authenticate user devices connecting to the network. You are asked to include a new Layer 2 interface connection from the conference room in your network. You must ensure that only a single device is allowed to authenticate on this port at one time to avoid users from being able to plug in a rogue switch to this port.

In this scenario, which 802.1X method would you use for the new interface?

  • A. single-secure supplicant mode
  • B. multiple supplicant mode
  • C. single supplicant mode
  • D. MAC-RADIUS
Show answer and explanation ▾

Correct answer: A

Single-secure supplicant mode allows only one end device to connect to the port, and no other device can connect until the first one logs off. A switch plugged into the port cannot bring extra devices onto the network.

Why the other options are wrong:

  • B. Multiple mode lets several devices authenticate on the same port.
  • C. Single mode authenticates only the first device and then lets other devices on the port through without authentication.
  • D. MAC RADIUS is an authentication method and does not limit the port to one device.

That was 25 of 106.

The full Juniper JN0-650 JNCIP-ENT pack has all 106 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.

Get the full pack

Not ready yet? Get the first 40 free as one PDF by email. Get the Half Pack →

About the JN0-650 exam

These 25 Juniper JN0-650 JNCIP-ENT questions are free here. The free PDF has 40, free by email.

They are drawn from the same bank as the full JN0-650 pack, which has 106 questions in total.

Back to blog