Juniper JN0-460 Practice Questions with Explanations
Free Juniper JN0-460 practice questions. 23 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.
JN0-460 practice questions
Question 1
A switch is claimed in a Mist organization using the activation code.
What are two possible device states that the switch will have in this scenario? (Choose two.)
- A. Connected
- B. Inactive
- C. Active
- D. Unassigned
Show answer and explanation ▾
Correct answer: B, D
Claiming a switch with an activation code only adds it to the organization inventory. Until it is assigned to a site it shows as Unassigned, and until it reaches the Mist cloud it is not shown as an active, connected device.
Why the other options are wrong:
- A. A switch shows as Connected only after it is assigned to a site and has reached the Mist cloud, which claiming alone does not do.
- C. Active is not a state that results from simply claiming the switch into the organization.
Question 2
What are the available Wired Assurance subscriptions for Juniper Mist switches in terms of port numbers?
- A. 24-port switch only
- B. 12-port and 24-port switches only
- C. 12-port, 24-port, and 48-port switches
- D. 12-port switch only
Show answer and explanation ▾
Correct answer: C
Wired Assurance subscriptions cover 12-port, 24-port and 48-port Juniper Mist switches. Any answer that names fewer port counts leaves out supported models.
Why the other options are wrong:
- A. 24-port switches are not the only size covered.
- B. The 48-port switches are covered too.
- D. 12-port switches are not the only size covered.
Question 3
Which description accurately defines a Mist AI 5-stage IP Clos network?
- A. It is a routing protocol specifically designed for campus fabrics, enabling efficient traffic forwarding and path selection.
- B. It is a type of EVPN tunnel encapsulation employed in data center networks for overlay routing.
- C. It is a hierarchical network architecture commonly used in campus fabrics, consisting of distribution, core, and access layers.
- D. It is a type of VXLAN tunnel encapsulation used in data center networks for overlay routing.
Show answer and explanation ▾
Correct answer: C
A 5-stage IP Clos campus fabric is a layered design with access, distribution and core tiers. It is a physical topology, not a routing protocol or a tunnel type.
Why the other options are wrong:
- A. It is a network design, not a routing protocol.
- B. EVPN encapsulation is a data center overlay technology and does not define a Clos network.
- D. VXLAN is a tunnel encapsulation, not a description of the Clos hierarchy.
Question 4
Which statement is correct about the Switch Insights section?
- A. A user can view traffic per port on this page.
- B. The Switch Insights feature is only available for EX Series switches.
- C. Only the top five switch events are available on this page.
- D. Users can rollback to a previously known configuration from this page.
Show answer and explanation ▾
Correct answer: A
The Switch Insights page shows traffic for each port, which helps spot busy or idle ports. It is a monitoring page, not a place to roll back configuration.
Why the other options are wrong:
- B. The feature is not limited to EX Series switches.
- C. The page is not limited to the top five switch events.
- D. Configuration rollback is not done from the Switch Insights page.
Question 5
Which statement is correct about a 3-stage campus fabric IP Clos?
- A. The distribution layer is connected to the access layer.
- B. The distribution layer is connected to the core layer.
- C. The core layer is connected to the access layer.
- D. The core layer devices are connected to each other.
Show answer and explanation ▾
Correct answer: A
In an IP Clos campus fabric each layer connects only to the layer next to it, so access switches uplink to the distribution layer. Devices in the same layer are not connected to each other.
Why the other options are wrong:
- B. This is not the statement that describes the 3-stage IP Clos design.
- C. This is not the statement that describes the 3-stage IP Clos design.
- D. In a Clos design, devices in the same layer are not connected to each other.
Question 6
When adopting your switches into the Juniper Mist cloud, you notice that the status of the switches is "Unassigned".
In this scenario, which additional step is required for the switches to show as "Connected" in the Juniper Mist dashboard?
- A. Use the Mist AI mobile application and rescan the QR code for adoption to your Mist site.
- B. You must restart each switch before Mist recognizes it on your dashboard.
- C. Troubleshoot the system configuration with the [show system connections | grep 2200] and [show configuration system services outboundssh] commands.
- D. Select each switch and assign them to your selected site.
Show answer and explanation ▾
Correct answer: D
Unassigned means the switches are in the organization inventory but do not belong to a site yet. Selecting the switches and assigning them to a site lets Mist manage them there, and they then show as Connected.
Why the other options are wrong:
- A. The switches are already in the inventory, so scanning the QR code again does not move them to a site.
- B. A restart does not change the status, because the switches still have no site.
- C. Those commands check the connection to the cloud, but the Unassigned status is about the missing site assignment.
Question 7
What are two limitations of using LLDP for identifying wired clients? (Choose two.)
- A. It requires LLDP to be configured on network devices.
- B. It is not scalable to large networks.
- C. It only operates between directly connected devices.
- D. It is supported by all wired client devices.
Show answer and explanation ▾
Correct answer: A, C
LLDP only identifies a client when the protocol is enabled on the devices involved, and its frames are exchanged only between directly connected neighbors. A device that does not run LLDP, or that sits behind another device, is not identified this way.
Why the other options are wrong:
- B. Scalability is not the limitation, since LLDP runs independently on each link.
- D. Universal support would be an advantage, not a limitation, and not every wired client runs LLDP.
Question 8
Which three steps should be part of the campus fabric deployment? (Choose three.)
- A. Define the physical connections.
- B. Define the networks of interest.
- C. Configure the DNS server.
- D. Choose the topology.
- E. Configure the group-based policy (GBP) tag.
Show answer and explanation ▾
Correct answer: A, B, D
A campus fabric deployment in Mist starts with choosing the topology, continues with defining the networks that the fabric will carry, and then defines the physical connections between the switches by selecting the ports that link them.
Why the other options are wrong:
- C. Configuring a DNS server is a general switch setting, not a step of the campus fabric deployment.
- E. A group-based policy tag is an optional segmentation feature, not a required step of the campus fabric deployment.
Question 9
A system administrator wants to onboard switches to a greenfield site.
In this scenario, which three actions will accomplish this task? (Choose three.)
- A. Use the Juniper Networks switch serial number.
- B. Use the Juniper Networks switch QR claim code.
- C. Use bulk claiming switches from a Juniper Mist sale order.
- D. Use the API to automate autoprovisioning of the switches to Juniper Mist.
- E. Use the Juniper Networks system MAC address number.
Show answer and explanation ▾
Correct answer: A, B, C
New cloud-ready switches are onboarded by claiming them into the organization. This can be done with the details of the individual switch, by scanning its QR claim code, or by claiming every switch on a sales order in bulk.
Why the other options are wrong:
- D. Automating with the API is not one of the claiming methods used to onboard new switches here.
- E. The system MAC address is not what Mist uses to claim a switch.
Question 10
Which statement is correct about an MP-BGP route-target?
- A. The route target is used to identify neighboring BGP routers that support the EVPN family.
- B. It is used by BGP to notify other BGP routers that it is EVPN enabled.
- C. It is used to identify the source and destination VRFs of MP-BGP routes.
- D. The route target is automatically created and must be unique for each VRF.
Show answer and explanation ▾
Correct answer: C
A route target is an attribute attached to MP-BGP routes. The exporting VRF tags its routes with the target, and a receiving device imports the routes into every VRF configured to import that target.
Why the other options are wrong:
- A. Neighbors that support the EVPN family are identified during BGP capability negotiation, not by a route target.
- B. EVPN support is advertised through the address family negotiated in the BGP session, not by a route target.
- D. Route targets can be configured manually and can be shared by several VRFs, so they are not always automatic or unique.
Question 11
Which component performs VXLAN encapsulation and de-encapsulation?
- A. VLAN
- B. VTEP
- C. root bridge
- D. WXLAN policy
Show answer and explanation ▾
Correct answer: B
A VXLAN tunnel endpoint (VTEP) adds the VXLAN header to Ethernet frames entering the overlay and removes it from frames leaving the overlay, so it is the component that encapsulates and de-encapsulates.
Why the other options are wrong:
- A. A VLAN is a Layer 2 segment, not a device function that encapsulates traffic.
- C. A root bridge is a spanning tree role and has no part in VXLAN encapsulation.
- D. A WXLAN policy controls wireless client traffic and does not encapsulate VXLAN.
Question 12
What are three wired service level expectations (SLEs) that comprise Juniper Mist Wired Assurance? (Choose three.)
- A. Capacity
- B. Successful Connects
- C. Switch Health
- D. Coverage
- E. Throughput
Show answer and explanation ▾
Correct answer: B, C, E
Juniper Mist Wired Assurance groups its wired service level expectations into Throughput, Successful Connect and Switch Health. Capacity appears only as a classifier inside Switch Health, and Coverage belongs to wireless.
Why the other options are wrong:
- A. Capacity is a classifier under the Switch Health SLE, not a wired SLE of its own.
- D. Coverage is a wireless SLE and is not part of the wired SLEs.
Question 13
You must provide physical connectivity between the core and access devices.
Which step of the campus fabric deployment process would allow you to accomplish this task?
- A. Define the topology type and select the devices.
- B. Configure the underlay network.
- C. Configure the overlay network.
- D. Apply the intent.
Show answer and explanation ▾
Correct answer: B
The underlay is the physical IP network of the fabric. Configuring it is the step where the links between the layers are defined, which provides the physical connectivity between the core and access devices.
Why the other options are wrong:
- A. Defining the topology type and selecting devices chooses the design and its members, but does not connect them.
- C. The overlay carries the virtual networks on top of connectivity that already exists.
- D. Applying the intent pushes the finished configuration and is not where the physical links are defined.
Question 14
You are asked to deploy a 5-stage IP Clos campus fabric using claim codes for all of the switches.
Which two statements are correct about this process? (Choose two.)
- A. The switches do not need to be assigned to the site where you plan to deploy the campus fabric.
- B. The switches must be online when you begin the Campus Fabric wizard.
- C. The switches do not need to be online when you begin the Campus Fabric wizard.
- D. The switches must be assigned to the site where you plan to deploy the campus fabric.
Show answer and explanation ▾
Correct answer: C, D
The Campus Fabric wizard builds the fabric from switches that belong to the site, so claimed switches must be assigned to that site first. They do not have to be online, because Mist stores the configuration and delivers it when each switch connects.
Why the other options are wrong:
- A. The wizard selects devices from the site, so the switches must be assigned to it.
- B. Being online is not a condition for starting the wizard.
Question 15
You are experiencing issues with your video streams.
In this scenario, which SLE and classifier should you inspect to see if BUM traffic is a problem?
- A. Throughput -> Interface Anomalies
- B. Throughput -> Congestion
- C. Throughput -> Storm Control
- D. Successful Connect -> Authentication
Show answer and explanation ▾
Correct answer: C
Storm control limits broadcast, unknown unicast and multicast traffic on a port. The Storm Control classifier of the Throughput SLE records the events where the storm control level was exceeded and packets were dropped.
Why the other options are wrong:
- A. Interface Anomalies does not report storm control drops of BUM traffic.
- B. Congestion does not report storm control drops of BUM traffic.
- D. The Authentication classifier covers client authentication failures, not BUM traffic.
Question 16
A customer has purchased five new switches and assigned them to a site.
In the configuration hierarchy, how should a user configure the name or role of each switch?
- A. Configure names and roles on the site-specific configuration.
- B. Configure additional CLI commands on each switch.
- C. Configure each switch individually on the Switch Configuration menu under the Switches menu.
- D. Add names and roles of each switch to the organization-level templates.
Show answer and explanation ▾
Correct answer: C
A name and a role are unique to each device, so they are set at the lowest level of the configuration hierarchy: the individual switch configuration reached from the Switches menu.
Why the other options are wrong:
- A. Site-level configuration applies to every switch in the site, so it cannot hold a different name for each switch.
- B. Additional CLI commands are not the intended place for per-switch names and roles.
- D. Organization-level templates hold shared settings, not the unique name of each switch.
Question 17
Which two elements are required for a brownfield adoption? (Choose two.)
- A. DNS resolution
- B. Internet connectivity
- C. an imported Configuration Template
- D. Outbound UDP 1280 access
Show answer and explanation ▾
Correct answer: A, B
An adopted switch opens an outbound connection to the Juniper Mist cloud. It therefore needs Internet connectivity to reach the cloud and DNS resolution to resolve the cloud host name.
Why the other options are wrong:
- C. Adoption does not depend on importing a configuration template.
- D. Outbound UDP 1280 is not the access that adoption relies on.
Question 18
You are asked to add a new VLAN in your network. You need to reference the same VLAN in multiple places in the configuration of switches and APs in your site.
Which Mist configuration tool will enable you to accomplish this task?
- A. site switch configuration
- B. site variables
- C. WLAN template
- D. switch template
Show answer and explanation ▾
Correct answer: B
A site variable is defined once for the site and then referenced by name wherever the value is needed. The same VLAN can be used in switch and AP configuration without retyping it, and it can differ from site to site.
Why the other options are wrong:
- A. Site switch configuration covers switches only and does not provide one value to reference in both switches and APs.
- C. A WLAN template applies to wireless settings and is not a shared value for switches.
- D. A switch template applies to switches and is not a shared value for APs.
Question 19
Which statement is correct about Juniper Mist Wired Assurance capabilities?
- A. Juniper Mist delivers operational visibility, sets service level expectations (SLEs), and monitors throughput, successful connects, and switch health using pre-connection and post-connection performance metrics.
- B. Juniper Mist can enforce throughput and successful connects but does not provide operational visibility or service level expectations (SLEs) for Juniper EX Series and QFX Series switches.
- C. Juniper Mist focuses solely on post-connection service level expectations (SLEs) and does not monitor throughput or successful connects.
- D. Juniper Mist primarily focuses on pre-connection service level expectations (SLEs) and does not monitor throughput, successful connects, or switch health on Juniper EX Series and QFX Series switches.
Show answer and explanation ▾
Correct answer: A
Wired Assurance gives operational visibility into the wired network and sets service level expectations for it. The wired SLEs are throughput, successful connects and switch health, built from pre-connection and post-connection metrics.
Why the other options are wrong:
- B. Wired Assurance does provide operational visibility and SLEs for EX Series and QFX Series switches.
- C. It uses both pre-connection and post-connection metrics and does monitor throughput and successful connects.
- D. It is not limited to pre-connection metrics, and it monitors throughput, successful connects and switch health.
Question 20
A company is planning to deploy a Juniper Mist campus fabric and wants to implement group-based policy (GBP) for microsegmentation.
Which statement is correct in this scenario?
- A. GBP requires access switches to be EX4100 or EX4400 switches.
- B. GBP configuration should be repeated on every individual switch in the fabric.
- C. GBP configuration must be applied to each individual switch in the fabric using the CLI.
- D. GBP can be implemented on any Juniper Networks switch that supports EVPN-VXLAN.
Show answer and explanation ▾
Correct answer: A
Group-based policy is enforced at the access layer and works only on switch models that support it. In the Mist campus fabric, that means using EX4100 or EX4400 switches as the access switches.
Why the other options are wrong:
- B. The policy is defined once in Mist and applied to the fabric, so it is not repeated on every switch.
- C. The policy is configured through Mist, not switch by switch with the CLI.
- D. Support for EVPN-VXLAN alone does not mean a switch supports group-based policy.
Question 21
You want a Juniper cloud-ready switch to connect to the Juniper Mist cloud.
In this scenario, which two statements are correct? (Choose two.)
- A. The switch must be running Junos OS version 23.2 or higher.
- B. The switch needs outbound connectivity to the Juniper Mist cloud using either TCP port 2200 or port 443.
- C. The switch must connect to the Juniper Agile Licensing Portal.
- D. The switch must connect to a DNS server.
Show answer and explanation ▾
Correct answer: B, D
A cloud-ready switch starts the connection itself. It needs a DNS server to resolve the host name of the Juniper Mist cloud and outbound access to the cloud on TCP port 2200 or port 443.
Why the other options are wrong:
- A. Junos OS 23.2 is not the minimum release for a cloud-ready switch to connect.
- C. Connecting to the Juniper Mist cloud does not depend on reaching the Juniper Agile Licensing Portal.
Question 22
You are asked to apply the same system-level configuration across all the devices in multiple sites using Mist AI.
According to Juniper Networks, which solution should you use in this scenario?
- A. Use the CLI on each device.
- B. Use the site-level switch configuration option in Mist AI.
- C. Use an organization-level template in Mist AI.
- D. Use the individual switch configuration option in Mist AI.
Show answer and explanation ▾
Correct answer: C
An organization-level switch template is created once and assigned to many sites, and every switch in those sites inherits its settings. That makes it the recommended way to keep the same system-level configuration across multiple sites.
Why the other options are wrong:
- A. Using the CLI on each device does not scale and works outside the Mist configuration model.
- B. Site-level configuration covers one site only, so it would be repeated for each site.
- D. Individual switch configuration is for settings unique to one device.
Question 23
You want to receive e-mail notifications when there are issues with your switches.
Where would you configure this capability in the Mist dashboard?
- A. Marvis conversational interface
- B. Wired SLEs
- C. Alerts Configuration
- D. Marvis Actions
Show answer and explanation ▾
Correct answer: C
E-mail notifications are set up on the Alerts Configuration page, where you choose which alert types are enabled and which administrators or e-mail addresses receive them.
Why the other options are wrong:
- A. The Marvis conversational interface answers troubleshooting questions and does not configure e-mail notifications.
- B. Wired SLEs display service level metrics and do not send e-mail notifications.
- D. Marvis Actions lists recommended fixes and is not where e-mail notifications are configured.
That was 23 of 69.
The full Juniper JN0-460 pack has all 69 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.
Get the full packNot ready yet? Get the first 24 free as one PDF by email. Get the Half Pack →
About the JN0-460 exam
These 23 Juniper JN0-460 questions are free here. The free PDF has 24, free by email.
They are drawn from the same bank as the full JN0-460 pack, which has 69 questions in total.