IASSC ICBB Practice Questions with Explanations
Free IASSC ICBB practice questions. 107 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.
ICBB practice questions
Question 1
A ___________ is used primarily to track the stability of the average value of a metric of interest.
- A. NP Chart
- B. Xbar-R Chart
- C. I-MR Chart
- D. C Chart
Show answer and explanation ▾
Correct answer: B
The Xbar-R chart tracks the subgroup average and the subgroup range, so it is the chart used to follow the stability of the average of a continuous metric.
Why the other options are wrong:
- A. An NP chart tracks the number of defective items, not an average.
- C. An I-MR chart tracks individual values and their moving range, not subgroup averages.
- D. A C chart tracks the count of defects per unit, not an average.
Question 2
For her injection molding project a Belt needed to track the percentage of defectives of a particular sample set so she used a ___________ to display the data?
- A. Individual Chart
- B. C Chart
- C. Xbar Chart
- D. P Chart
Show answer and explanation ▾
Correct answer: D
A P chart tracks the proportion or percentage of defective items in a sample, which is what the Belt needed for percent defective.
Why the other options are wrong:
- A. An individual chart tracks single continuous measurements.
- B. A C chart tracks the number of defects per unit, not a percentage of defectives.
- C. An Xbar chart tracks the average of continuous data, not a percentage defective.
Question 3
Control Charts were developed by Dr. Shewhart to track data over time. To detect Special Cause variation the Control Charts use which of these?
- A. Data shift analysis
- B. Outlier analysis methods
- C. Center Line and Control Limits
- D. None of the above
Show answer and explanation ▾
Correct answer: C
Control charts separate special cause variation from common cause by comparing points to the center line and control limits.
Why the other options are wrong:
- A. Data shift analysis is not the mechanism control charts use to detect special causes.
- B. Outlier analysis methods are not how control charts flag special cause variation.
- D. The center line and control limits are the correct answer, so None of the above is wrong.
Question 4
Common and ______________ Cause Variation are the focus of Statistical Process Control.
- A. Uncommon
- B. Ordinary
- C. Special
- D. Selective
Show answer and explanation ▾
Correct answer: C
Statistical Process Control focuses on common cause and special cause variation, and its charts help tell the two apart.
Why the other options are wrong:
- A. Uncommon cause is not a standard term in statistical process control.
- B. Ordinary cause is another name for common cause, which the question already names.
- D. Selective cause is not a standard term in statistical process control.
Question 5
Special Cause Variation falls into which two categories?
- A. Natural & Unnatural
- B. Short Term & Long Term
- C. Assignable & Pattern
- D. Attribute & Discreet
Show answer and explanation ▾
Correct answer: C
Special Cause Variation is grouped into two categories: Assignable causes, which can be traced to a specific source, and Pattern causes, which show up as non-random behavior in the data such as runs, trends or cycles.
Why the other options are wrong:
- A. Natural and Unnatural are not the two categories used for Special Cause Variation.
- B. Short Term and Long Term describe the time frame of capability data, not categories of Special Cause Variation.
- D. Attribute and Discrete describe data types, not categories of variation.
Question 6
Range Charts are the technique used to determine if Special Causes are occurring within the subgroups of the ______________.
- A. Histograms
- B. SPC Charts
- C. NP Charts
- D. Pareto Charts
Show answer and explanation ▾
Correct answer: B
A Range Chart plots the range within each subgroup of an SPC Chart, so it shows whether Special Causes are acting on the within-subgroup variation.
Why the other options are wrong:
- A. Histograms show the shape of a distribution and have no subgroups plotted over time.
- C. NP Charts track the number of defective items and are not paired with a Range Chart.
- D. Pareto Charts rank categories by frequency and have no subgroups.
Question 7
If the production is for higher volume and monitoring and the Mean and variability is to be monitored for four machines producing product and the characteristic to be monitored is Variable Data, which SPC Chart is best to be selected?
- A. Xbar-R Chart
- B. Individual-MR Chart
- C. NP Chart
- D. CUSUM Chart
Show answer and explanation ▾
Correct answer: A
With Variable Data and high volume, measurements can be collected in subgroups. The Xbar-R Chart then monitors the Mean on the Xbar Chart and the variability on the Range Chart.
Why the other options are wrong:
- B. An Individual-MR Chart is used when only single measurements are available, which is not the case at high volume.
- C. An NP Chart is for Attribute Data, the number of defective items.
- D. A CUSUM Chart is aimed at detecting small shifts in the Mean and is not the standard pair for Mean and variability.
Question 8
When a Belt Poka-Yokes a defect out of the process entirely then she should track the activity with a robust SPC system on the characteristic of interest in the defect as an early warning system.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: B
When Poka-Yoke removes a defect from the process entirely, the defect can no longer occur, so there is nothing left to monitor and SPC on that characteristic adds no value.
Why the other options are wrong:
- A. SPC is a warning system for defects that can still occur, and a fully mistake-proofed defect cannot.
Question 9
Following the completion of a LSS project the Belt not only creates a Control Plan he also develops a _____________ so those involved in the process know what to do when the critical metrics move out of spec.
- A. Response Plan
- B. Call List
- C. Chain-of-Command
- D. Defect Analysis Plan
Show answer and explanation ▾
Correct answer: A
A Response Plan tells the people who run the process exactly what action to take, and who takes it, when a critical metric moves outside its limits.
Why the other options are wrong:
- B. A Call List names contacts but does not define the actions to take.
- C. A Chain-of-Command shows reporting lines, not the reaction to an out-of-spec metric.
- D. Defect Analysis Plan is not the document that accompanies a Control Plan.
Question 10
The Control Limits width varies if the sample size varies for which type of chart?
- A. P Charts
- B. NP Charts
- C. Xbar-R Charts
- D. Time Series Charts
Show answer and explanation ▾
Correct answer: A
P Chart limits are calculated from the subgroup size, so when the sample size changes from one subgroup to the next the Control Limits widen or narrow with it.
Why the other options are wrong:
- B. NP Charts are used with a constant sample size, so their limits stay level.
- C. Xbar-R Charts are not the chart defined by limits that move with a varying sample size.
- D. Time Series Charts have no Control Limits.
Question 11
Which of these elements are not included in Implementation plans?
- A. Work breakdown structure
- B. Risk management plans
- C. Cost/Benefit ratios
- D. Planned audits of work completion
Show answer and explanation ▾
Correct answer: C
Cost/Benefit ratios are used earlier, to justify and select a solution. An Implementation Plan describes how the chosen solution is rolled out: the work, the risks and the checks on completion.
Why the other options are wrong:
- A. A work breakdown structure is a standard part of an Implementation Plan.
- B. Risk management plans are a standard part of an Implementation Plan.
- D. Planned audits of work completion are a standard part of an Implementation Plan.
Question 12
Upon completion and validation of an improvement to a process a Belt and the Project Team create a Control Plan that contains which of these?
- A. Standard operating work description of the process change
- B. Description of the monitoring system in place to assure continued compliance
- C. Summary of the targeted critical metrics for process performance measurement
- D. All of the above
Show answer and explanation ▾
Correct answer: D
A Control Plan documents the standard work for the changed process, the monitoring system that assures continued compliance and the critical metrics with their targets, so all three items belong in it.
Why the other options are wrong:
- A. The standard work description is only one of the three elements the Control Plan contains.
- B. The monitoring system description is only one of the three elements the Control Plan contains.
- C. The summary of critical metrics is only one of the three elements the Control Plan contains.
Question 13
How many experimental runs exist in a Full Factorial and fully randomized design for 4 factors with 2 replicates for the Corner Points and no Center Points? The factors in the experiment are only at 2-levels.
- A. 10
- B. 32
- C. 256
- D. 64
Show answer and explanation ▾
Correct answer: B
A 2-level Full Factorial with 4 factors has 2 x 2 x 2 x 2 = 16 corner point runs. Two replicates double that to 32 runs.
Why the other options are wrong:
- A. 10 is not the product of the levels and replicates for this design.
- C. 256 comes from the wrong calculation and is not the run count of a 4-factor, 2-level design with 2 replicates.
- D. 64 runs would need a larger design, such as 5 factors with 2 replicates.
Question 14
If an experiment has 5 factors and no replicates for a 2-level Experimental Design with 16 experimental runs which statement is incorrect?
- A. The Experimental Design is half-fractional
- B. The Main Effects are confounded with only 4-way interactions
- C. The Main Effects for the 5 factors are not aliased or confounded but the 2-way interactions are confounded with the 3-way interactions
- D. The experiment has 8 experimental runs with the first factor at the high level
Show answer and explanation ▾
Correct answer: C
Five 2-level factors in 16 runs is a half fraction of the 32-run Full Factorial. In this design each Main Effect is confounded with a 4-way interaction, so the claim that the Main Effects are not aliased or confounded is the incorrect statement.
Why the other options are wrong:
- A. 16 runs is half of the 32 runs in the Full Factorial, so the design is half-fractional.
- B. In this half fraction each Main Effect is confounded with a 4-way interaction.
- D. Each factor is at the high level in half of the 16 runs, which is 8 runs.
Question 15
Fractional Factorial, ____________and Response Surface Method are types of planned experiments.
- A. Multi-Vari Analysis
- B. Baldridge Channels
- C. One Factor at a Time or OFAT
- D. Factorial Design
Show answer and explanation ▾
Correct answer: D
Factorial Design, Fractional Factorial and Response Surface Method are all structured, planned experiments in which the factor settings are deliberately set for every run.
Why the other options are wrong:
- A. Multi-Vari Analysis observes the process passively and does not set the factors.
- B. Baldridge Channels is not a type of planned experiment.
- C. One Factor at a Time is the unstructured approach that planned experiments replace.
Question 16
Relative to a Design of Experiments the term ________________ refers to variables being a linear combination of each other.
- A. Mirror Image
- B. Directly Parallel
- C. Collinear
- D. None of the above
Show answer and explanation ▾
Correct answer: C
Variables are Collinear when one can be written as a linear combination of the others, which makes their separate effects impossible to estimate.
Why the other options are wrong:
- A. This is not the term for variables that are linear combinations of each other.
- B. Directly Parallel is not the term used in Design of Experiments for this condition.
- D. Collinear is the correct term, so None of the above is wrong.
Question 17
Which statement(s) are incorrect about Fractional Factorial Designs?
- A. A Half Fractional Design for 5 factors has the same number of experimental runs as a Full Factorial Design for 4 factors assuming no repeats or replicates or Center Points
- B. Quarter Fractional experiments can exist for those with 4 factors
- C. Resolution V design is desired while controlling costs of experimentation
- D. Half Fractional experiments do not exist for those designs with only 2 factors
Show answer and explanation ▾
Correct answer: C
Resolution V designs give the cleanest estimates of a fractional design but need the most runs, so they are not the choice made to hold down the cost of experimentation. Lower resolution designs are used for that.
Why the other options are wrong:
- A. A half fraction of 5 factors and a Full Factorial of 4 factors both have 16 runs, so this statement holds.
- B. A quarter fraction of a 4-factor design can be laid out in 4 runs, so this statement is not the incorrect one.
- D. Halving a 2-factor design leaves 2 runs in which the two factors cannot be separated, so this statement holds.
Question 18
If in an experiment all possible variable pairs sum to zero the design is Orthogonal.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
A design is Orthogonal when the coded settings of every pair of factor columns, multiplied together and summed over all runs, total zero. This lets each effect be estimated independently of the others.
Why the other options are wrong:
- B. Pairs of columns that sum to zero are exactly the condition that defines an Orthogonal design.
Question 19
Which Experimental Design typically is most associated with the fewest number of input variables or factors in the design?
- A. Fractional Factorial design
- B. Full Factorial design
- C. Simple Linear Regression
- D. Response Surface Design
Show answer and explanation ▾
Correct answer: D
Response Surface Designs are run late in experimentation to optimize the few factors that screening has already shown to matter, so they typically involve the fewest factors.
Why the other options are wrong:
- A. Fractional Factorial designs are used to screen a large number of factors.
- B. Full Factorial designs typically carry more factors than a Response Surface Design.
- C. Simple Linear Regression is an analysis method, not an Experimental Design.
Question 20
The method of Steepest Ascent guides you toward a target inside the original inference space.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: B
The method of Steepest Ascent moves the experiment step by step along the path of greatest improvement toward an optimum that lies outside the original inference space.
Why the other options are wrong:
- A. Steepest Ascent is used to leave the original experimental region, not to find a target inside it.
Question 21
Situations where standardized work needs to be incorporated include all of these except _____________________.
- A. Machines continually operating to reduce the labor cost per piece
- B. Lack of a system to assure proper inventory levels at repair stations
- C. Changeover instructions incomplete
- D. Process flow for the same product assembly taking various cycle time for completion
Show answer and explanation ▾
Correct answer: A
Running machines continually to lower the labor cost per piece is a production policy that leads to overproduction. It is not a gap in how the work is defined, so standardized work does not address it.
Why the other options are wrong:
- B. A missing system for inventory levels at repair stations is fixed by defining a standard method.
- C. Incomplete changeover instructions are a direct case for standardized work.
- D. Varying cycle times for the same assembly show the work is not done one standard way.
Question 22
The Lean toolbox includes all of these items except ________________.
- A. Mistake Proofing
- B. Visual Factory
- C. Design of Experiments
- D. Inventory Management
Show answer and explanation ▾
Correct answer: C
Design of Experiments is a statistical tool from the Six Sigma side of the toolkit. Mistake Proofing, Visual Factory and Inventory Management are Lean tools.
Why the other options are wrong:
- A. Mistake Proofing is a Lean tool.
- B. Visual Factory is a Lean tool.
- D. Inventory Management is part of the Lean toolbox.
Question 23
Questions that can be best answered by a Visual Factory include all of these except _____________________.
- A. Are downtime issues easily noted?
- B. Can extra inventory be seen easily?
- C. Are unneeded tools or supplies easily noted?
- D. Are setups optimized for lower scrap levels?
Show answer and explanation ▾
Correct answer: D
A Visual Factory makes the status of the workplace obvious at a glance. Whether setups are optimized for lower scrap takes data and analysis and cannot be seen by looking at the work area.
Why the other options are wrong:
- A. Downtime is a status that visual signals make easy to see.
- B. Extra inventory is made visible by marked locations and limits.
- C. Unneeded tools or supplies stand out in a visually organized workplace.
Question 24
If a Six Sigma project was to reduce repair station inventory and the team found the inventory was creeping up over time which Lean tools should be considered in the Control Phase to reestablish and sustain the project success?
- A. Review the Visual Factory to assure inventory in excess of desired visible
- B. Improve the lighting to assure adequate visibility
- C. Analyze data from supplier deliveries
- D. Reword the standardized work instructions to use active verbs and not passive phrases
Show answer and explanation ▾
Correct answer: A
A Visual Factory makes inventory above the desired level obvious at once, so the creep is noticed and corrected as it happens. Reviewing it restores the control that sustains the inventory reduction.
Why the other options are wrong:
- B. Better lighting does not show whether inventory is above the desired level.
- C. Analyzing supplier delivery data is not a Lean control for inventory held at the repair station.
- D. Rewording work instructions does not make excess inventory visible.
Question 25
When a Belt implements an improvement that is automated thus requiring no particular understanding for use he has applied which Lean tool?
- A. Mistake Proofing
- B. Kaizen Event
- C. 5S
- D. None
Show answer and explanation ▾
Correct answer: D
Automating an improvement so that it needs no understanding from the user is an engineering change to the process. It is not Mistake Proofing, a Kaizen Event or 5S, so none of the listed Lean tools has been applied.
Why the other options are wrong:
- A. Mistake Proofing targets a specific error at its source, which is not what automating the improvement describes.
- B. A Kaizen Event is a short team improvement effort, not an automated solution.
- C. 5S organizes and standardizes the workplace and is not automation.
Question 26
Kaizens or Kaikakus and Six Sigma projects are intended to create incremental process improvements versus breakthrough, significant improvements.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: B
In this body of knowledge, Kaizen or Kaikaku events and Six Sigma projects are aimed at breakthrough, significant improvement of a process rather than minor, incremental gains, so the statement is false.
Why the other options are wrong:
- A. These efforts are intended to deliver breakthrough improvement, not merely incremental change.
Question 27
Which of these items contribute to what is necessary for successful Kaizen events?
- A. Analysis tools
- B. Management support
- C. Operator support
- D. All of these answers are correct
Show answer and explanation ▾
Correct answer: D
A Kaizen event succeeds when the team has analysis tools to find the causes, management support to free people and approve changes, and operator support to make the changes stick, so all three are needed.
Why the other options are wrong:
- A. Analysis tools alone are not enough without management and operator support.
- B. Management support alone is not enough without analysis tools and operator support.
- C. Operator support alone is not enough without analysis tools and management support.
Question 28
Kanban establishes a means of monitoring production, conveyance and delivery information such that efficient flow is established. The method used by Kanban is to require a _________ before anything moves.
- A. Sign-off
- B. Signal
- C. Bell to ring
- D. Work order
Show answer and explanation ▾
Correct answer: B
Kanban is a pull system: nothing is produced or moved until a signal, such as a card or an empty container, shows that the downstream step needs it.
Why the other options are wrong:
- A. A sign-off is an approval step, not the trigger Kanban uses.
- C. Kanban does not require a bell; the requirement is a signal of downstream need.
- D. A work order pushes work by schedule, which is the opposite of the Kanban pull.
Question 29
When a Belt decides to use written procedures and visual controls to improve the consistency of the tasks that must occur in the process he is improving he has utilized the _________________ activity of 5S.
- A. Sustaining
- B. Sorting
- C. Standardizing
- D. Straightening
Show answer and explanation ▾
Correct answer: C
Standardizing is the 5S activity that sets written procedures and visual controls so that tasks are done the same way every time.
Why the other options are wrong:
- A. Sustaining is the discipline of keeping the 5S practices going over time.
- B. Sorting removes items that are not needed from the work area.
- D. Straightening arranges the needed items so each has a set place.
Question 30
Fractional Factorial designs are used to reduce the ____________ because the number of runs has been lowered.
- A. Time and cost of experiments
- B. Number of people involved
- C. Number of data measurement points
- D. Output summary
Show answer and explanation ▾
Correct answer: A
A Fractional Factorial runs only a chosen portion of the Full Factorial combinations. Fewer runs mean less time and lower cost for the experiment.
Why the other options are wrong:
- B. The number of people involved is not what a Fractional Factorial is designed to reduce.
- C. Fewer data points is a result of fewer runs, not the benefit the design is chosen for.
- D. The output summary is not what a Fractional Factorial reduces.
Question 31
Fractional Factorial Designs are used to analyze factors to model the output as a function of inputs if Hypothesis Testing in the Analyze Phase was inadequate to sufficiently narrow the factors that significantly impact the output(s).
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
When Hypothesis Testing in the Analyze Phase leaves too many candidate factors, a Fractional Factorial Design screens them efficiently and models the output as a function of the inputs that matter.
Why the other options are wrong:
- B. Screening and modeling the remaining factors is exactly what Fractional Factorial Designs are used for.
Question 32
A Factorial Experiment based on a Level 2 Design with 6 factors would require 16 runs to fully assess the interactions.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: B
A 2-level design with 6 factors needs 2 to the power of 6, which is 64 runs, to assess every interaction. Sixteen runs would be only a quarter fraction.
Why the other options are wrong:
- A. 16 runs is a quarter fraction of the 64 runs needed and leaves interactions confounded.
Question 33
A Full Factorial experiment using a 3 level 3 factor approach has been proposed to test the viability of an extrusion machine experiment.
How many treatment combinations will this approach involve?
- A. 6
- B. 9
- C. 27
- D. 54
Show answer and explanation ▾
Correct answer: C
A Full Factorial with 3 factors at 3 levels each has 3 x 3 x 3 = 27 treatment combinations.
Why the other options are wrong:
- A. 6 comes from adding the levels and factors, not from multiplying the levels.
- B. 9 is the count for 2 factors at 3 levels, not 3 factors.
- D. 54 is double the 27 combinations and would apply only with a replicate.
Question 34
Screening experiments are the proper choice when a Belt is faced with the situation of highly Fractional Factorial Designs.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
Screening experiments use highly Fractional Factorial Designs to test many factors in few runs and find the vital few that drive the output.
Why the other options are wrong:
- B. Highly fractional designs are the standard tool for screening experiments.
Question 35
A valid mathematical Regression represents all of the characteristics shown except ___________________________.
- A. The residuals when plotted follow a Normal Distribution
- B. The sum of the residuals is zero
- C. All of the standardized residuals will be within ±3 Standard Deviations
- D. Most standardized residuals are within ±2 Standard Deviations
Show answer and explanation ▾
Correct answer: C
Residuals of a valid Regression are Normally Distributed around zero, so most standardized residuals fall within 2 Standard Deviations and nearly all within 3. A Normal Distribution does not guarantee that every single one stays within 3.
Why the other options are wrong:
- A. Normally Distributed residuals are a requirement of a valid Regression.
- B. The residuals of a least squares Regression sum to zero.
- D. About 95% of standardized residuals fall within 2 Standard Deviations in a valid model.
Question 36
When a Belt conducts a Linear Correlation Analysis and finds that as an X increases the Y also increase then he has proven a ______________ correlation.
- A. Negative
- B. Positive
- C. Monomial
- D. Single alignment
Show answer and explanation ▾
Correct answer: B
When Y increases as X increases the two variables move in the same direction, which is a positive correlation.
Why the other options are wrong:
- A. A negative correlation means Y decreases as X increases.
- C. Monomial is not a type of correlation.
- D. Single alignment is not a type of correlation.
Question 37
A valid Multiple Linear Regression (MLR) is characterized by all of these except _______________________.
- A. It is an assumption that the X’s (inputs) are not correlated to each other
- B. The X’s (inputs) are assumed to be independent of each other
- C. MLR is conducted based on a deliberate form of experimentation
- D. The Residuals from MLR analysis have to be Normally Distributed
Show answer and explanation ▾
Correct answer: C
Multiple Linear Regression is normally run on historical or observed process data. Deliberate, structured changes to the inputs are the mark of a designed experiment, not of MLR.
Why the other options are wrong:
- A. A valid MLR assumes the inputs are not correlated with each other.
- B. A valid MLR assumes the inputs are independent of each other.
- D. Normally Distributed residuals are a requirement of a valid MLR.
Question 38
It would be more likely than not for a Belt conducting a Regression Analysis to find that the _______________________.
- A. r2 value is smaller than the absolute value of r
- B. Correlation Coefficient equals r2
- C. Coefficient of Determination is less than r2
- D. Correlation Coefficient equals r divided by 2
Show answer and explanation ▾
Correct answer: A
The Correlation Coefficient r lies between -1 and 1, and squaring a number whose absolute value is below 1 makes it smaller. In practice r is almost never exactly 0, 1 or -1, so r squared is smaller than the absolute value of r.
Why the other options are wrong:
- B. The Correlation Coefficient is r, not r squared.
- C. The Coefficient of Determination is r squared, so it cannot be less than r squared.
- D. The Correlation Coefficient is r itself, not r divided by 2.
Question 39
When a Belt properly analyzes the results of an experiment he must examine the Residuals in expectation of finding all of the following except _________.
- A. Some Residuals higher than others
- B. Some Residuals lower than others
- C. All Residuals within 2 Standard Deviations of the Mean
- D. Residuals will represent a Linear Regression
Show answer and explanation ▾
Correct answer: D
Residuals from a sound model scatter randomly around zero with no structure. Residuals that themselves follow a linear relationship show that the model has missed something, so that is not what the Belt expects to find.
Why the other options are wrong:
- A. Residuals vary in size, so some being higher than others is expected.
- B. Residuals vary in size, so some being lower than others is expected.
- C. Residuals staying in a narrow band around the Mean is what a well-fitting model is expected to show.
Question 40
Which of these might contribute to similar distributions having Unequal Variance?
- A. Extreme tails
- B. Outliers
- C. Multiple Modes
- D. All of the above
Show answer and explanation ▾
Correct answer: D
Extreme tails, outliers and multiple modes each widen the spread of one sample relative to another, so any of them can make otherwise similar distributions show Unequal Variance.
Why the other options are wrong:
- A. Extreme tails are only one of the three listed contributors.
- B. Outliers are only one of the three listed contributors.
- C. Multiple Modes are only one of the three listed contributors.
Question 41
A Belt working in a supply chain environment has to make a decision to change suppliers of critical raw materials for a new product upgrade. The purchasing manager is depending on the Belts effort requiring that the average cost of an internal critical raw material component be less than or equal to $4,200 in order to stay within budget. Using a sample of 35 first article components, a Mean of the new product upgrade price of $4,060, and a Standard Deviation of $98 was estimated. The Alternative Hypothesis in the above example is?
- A. The Standard Deviation is equal to $300.
- B. The Mean is less than $4,320.
- C. The Mean is equal to $4,060.
- D. The Mean is less than $4,200.
- E. The Mean is greater than $ 4,200.
Show answer and explanation ▾
Correct answer: E
The Null Hypothesis carries the equality, so it states the budget requirement that the Mean cost is at most $4,200. The Alternative Hypothesis is its complement: the Mean is greater than $4,200.
Why the other options are wrong:
- A. The test concerns the Mean, and $300 does not appear in the scenario.
- B. $4,320 is not the budget limit in the scenario.
- C. $4,060 is the sample Mean, a statistic, and not a claim about the population.
- D. A Mean below $4,200 sits inside the budget condition stated by the Null Hypothesis.
Question 42
A Belt working in a supply chain environment has to make a decision to change suppliers of critical raw materials for a new product upgrade. The purchasing manager is depending on the Belts effort requiring that the average cost of an internal critical raw material component be less than or equal to $3,600 in order to stay within budget. Using a sample of 42 first article components, a Mean of the new product upgrade price of $3,200 and a Standard Deviation of $180 was estimated. Based on the data provided, the Z value for the data assuming a Normal Distribution is?
- A. 1.11
- B. 2.22
- C. 4.30
- D. 5.42
Show answer and explanation ▾
Correct answer: B
Z is the distance from the Mean to the limit in Standard Deviations: (3,600 - 3,200) / 180 = 2.22.
Why the other options are wrong:
- A. 1.11 is half of the value the formula gives.
- C. 4.30 does not result from dividing the $400 gap by the $180 Standard Deviation.
- D. 5.42 does not result from dividing the $400 gap by the $180 Standard Deviation.
Question 43
A Belt working in a supply chain environment has to make a decision to change suppliers of critical raw materials for a new product upgrade. The purchasing manager is depending on the Belts effort requiring that the average cost of an internal critical raw material component be less than or equal to $3,800 in order to stay within budget. Using a sample of 38 first article components, a Mean of the new product upgrade price of $3,680, and a Standard Deviation of $120 was estimated. In order to increase the Long Term Z value to 5, what is the maximum long term variation in pricing the Belt can accept for his upgraded critical raw material component?
- A. $6
- B. $12
- C. $24
- D. $48
Show answer and explanation ▾
Correct answer: C
The gap between the limit and the Mean is 3,800 - 3,680 = $120. For a Z of 5 the Standard Deviation can be at most 120 / 5 = $24.
Why the other options are wrong:
- A. $6 is well below the largest Standard Deviation that still gives a Z of 5.
- B. $12 is half of the largest Standard Deviation that still gives a Z of 5.
- D. A Standard Deviation of $48 gives a Z of only 2.5.
Question 44
Sally and Sara sell flower pots at their garage sale. Sally motivates Sara mentioning that they will sell a minimum of 15 pots per day if the outside temperature exceeds 60o F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 13.6 pots per day were sold with a Standard Deviation of 0.7 pots. For the sales accomplished above, what test would validate if they met their requirements?
- A. F Test
- B. Test for Equal Variance
- C. Chi Square Test
- D. One-Sample t-Test
Show answer and explanation ▾
Correct answer: D
One sample Mean, 13.6 pots per day, is compared with a single target value of 15 using the sample Standard Deviation from Normally Distributed data. That is the One-Sample t-Test.
Why the other options are wrong:
- A. The F Test compares the variances of two samples.
- B. A Test for Equal Variance compares spread between samples, not a Mean with a target.
- C. The Chi Square Test is used for counts and proportions, not a sample Mean.
Question 45
Sally and Sara sell flower pots at their garage sale. Sally motivates Sara mentioning that they will sell a minimum of 15 pots per day if the outside temperature exceeds 60o F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 13.6 pots per day were sold with a Standard Deviation of 0.7 pots. The statistical Degrees of Freedom for this example are?
- A. 1
- B. 29
- C. 30
- D. 31
- E. 2
Show answer and explanation ▾
Correct answer: B
For a one-sample test of the Mean the Degrees of Freedom are the sample size minus 1: 30 - 1 = 29.
Why the other options are wrong:
- A. 1 is not the sample size minus one.
- C. 30 is the sample size, before subtracting 1.
- D. 31 adds 1 to the sample size instead of subtracting it.
- E. 2 is not the sample size minus one.
Question 46
Sally and Sara sell flower pots at their garage sale. Martha motivates Rose mentioning that they will sell a minimum of 16 pots per day if the outside temperature exceeds 60o F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 15.2 pots per day were sold with a Standard Deviation of 0.6 pots.
What is the Z value for this sales process?
- A. 0.67
- B. 1.13
- C. 1.33
- D. 2.66
Show answer and explanation ▾
Correct answer: C
Z is the distance between the requirement and the Mean in Standard Deviations: (16 - 15.2) / 0.6 = 1.33.
Why the other options are wrong:
- A. 0.67 is half of the value the formula gives.
- B. 1.13 does not result from dividing 0.8 by 0.6.
- D. 2.66 is double the value the formula gives.
Question 47
The relationship between a response variable and one or more independent variables is investigated and modeled by use of __________________.
- A. X-Y Matrix
- B. Baldridge Assessment
- C. Analysis of Variance (ANOVA)
- D. Critical X's Definition
Show answer and explanation ▾
Correct answer: C
Analysis of Variance tests and models how a response variable changes across the levels of one or more independent variables by splitting the total variation into its sources.
Why the other options are wrong:
- A. An X-Y Matrix ranks inputs by team scoring and does not model a statistical relationship.
- B. A Baldridge Assessment reviews organizational quality practices, not variable relationships.
- D. Critical X's Definition is not a statistical modeling method.
Question 48
An ANOVA used across many dependent variables could increase the Beta risk.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: B
Running the analysis across many variables multiplies the chances of a false positive, which raises the Alpha risk. It is not the Beta risk that grows, so the statement is false.
Why the other options are wrong:
- A. Repeated testing inflates the Alpha risk of a false positive, not the Beta risk.
Question 49
The Mann-Whitney test is a powerful test and is unique to situations from which of the choices listed? (Note: There are 2 correct answers). (Choose two.)
- A. Testing the identity of two populations
- B. Focuses on equality of the Median of the two populations
- C. Less powerful than the traditional "t-test"
- D. More widely applicable than the traditional "t-test"
Show answer and explanation ▾
Correct answer: B, D
The Mann-Whitney test compares two samples on the equality of their Medians and does not need Normally Distributed data, so it applies in more situations than the traditional t-test.
Why the other options are wrong:
- A. The test is centered on comparing the Medians of two populations, not on establishing their identity.
- C. The stem describes a powerful test, and lower power is not what sets the Mann-Whitney test apart.
Question 50
Assessing process proportion as opposed to evaluating a process with respect to a set target can be done using which of these?
- A. Process proportion equals some value range
- B. Process proportion equals some desired value
- C. Target is current
- D. Proportion of the tail is equal
Show answer and explanation ▾
Correct answer: B
A test of a process proportion asks whether the proportion equals some desired value, in the same way a test of the Mean compares a process with a set target.
Why the other options are wrong:
- A. The hypothesis is stated against a single desired value, not a range.
- C. Target is current is not a hypothesis about a process proportion.
- D. Equal tail proportions is not how a process proportion is assessed.
Question 51
A Non-parametric Test should be used if just one distribution is not Normal out of the two or more gathered.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
Parametric tests assume every sample comes from a Normal Distribution. If even one of the samples is not Normal, that assumption fails and a Non-parametric Test should be used.
Why the other options are wrong:
- B. One Non-normal sample is enough to break the assumption behind the parametric tests.
Question 52
Contingency Tables are used to test for association, or dependency, between two or more classifications.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
A Contingency Table cross-classifies counts by two or more categories, and the Chi Square test on it shows whether the classifications are associated or independent.
Why the other options are wrong:
- B. Testing for association between classifications is exactly what Contingency Tables are used for.
Question 53
A(n) ______________ is best used to compare a Machine 1 average quality characteristic to the same quality characteristic of Machine 2.
- A. F test
- B. 1-Sample t-test
- C. 2-Sample t-test
- D. ANOVA test
Show answer and explanation ▾
Correct answer: C
A 2-Sample t-test compares the Means of two independent samples, which is exactly the case of one machine's average against another machine's average for the same characteristic.
Why the other options are wrong:
- A. An F test compares two variances, not two averages.
- B. A 1-Sample t-test compares one sample Mean with a fixed target value, not with a second sample.
- D. ANOVA is the tool for comparing the Means of three or more groups.
Question 54
A(n) ________________ has occurred when two inputs have a greater impact on a change in the output than either of the inputs has by itself.
- A. Dependency
- B. Bimodal reaction
- C. Interaction
- D. Amplified effect
Show answer and explanation ▾
Correct answer: C
An Interaction exists when the effect of one input on the output depends on the level of another input, so the two together change the output more than either does alone.
Why the other options are wrong:
- A. Dependency is not the term for the combined effect of two inputs on an output.
- B. Bimodal describes a distribution with two peaks, not the combined effect of two inputs.
- D. Amplified effect is not a standard statistical term for this.
Question 55
When conducting a Hypothesis Test using Continuous Data the proper sample size is influenced by the extent to which we need to assess a Difference to be detected and the inherent variation in the process.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
Sample size for a test on Continuous Data depends on the size of the Difference that must be detected and on the process variation. A smaller difference or a larger Standard Deviation calls for more samples.
Why the other options are wrong:
- B. Both the difference to be detected and the inherent variation are inputs to the sample size calculation.
Question 56
The validity of the decision made with Hypothesis Testing is dependent upon all of these except ___________________.
- A. Beta risk
- B. Alpha risk
- C. Range of data
- D. Sample size
Show answer and explanation ▾
Correct answer: C
The soundness of a Hypothesis Test decision rests on the Alpha risk and Beta risk accepted and on the sample size used. The Range of the data is a descriptive statistic and is not one of the risks or design choices that set the validity of the decision.
Why the other options are wrong:
- A. Beta risk is the chance of missing a real difference, so it directly affects the validity of the decision.
- B. Alpha risk is the chance of declaring a difference that is not there, so it directly affects the validity of the decision.
- D. Sample size sets how much confidence and power the test has.
Question 57
Statistical Difference is the magnitude of difference or change required to distinguish between a true difference, brought about by change or improvement, and one that could have occurred by chance.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
Hypothesis Testing separates a real difference caused by a change or improvement from one that could have happened by chance. The Statistical Difference is the size of change needed to make that distinction.
Why the other options are wrong:
- B. The statement gives the definition used in Hypothesis Testing, so it is not false.
Question 58
To be an effective Lean Six Sigma practitioner one must understand the difference between ___________________________.
- A. ANOVA and the Analysis of Variance
- B. Nonparametric tests and tests of Non-normal Data
- C. F-test and test of variances of 2 samples
- D. Practical and Statistical significance
Show answer and explanation ▾
Correct answer: D
A result can be statistically significant yet too small to matter to the business, and a practically important change still needs statistical proof. A practitioner must judge both Practical and Statistical significance before acting.
Why the other options are wrong:
- A. ANOVA is the abbreviation of Analysis of Variance, so there is no difference to understand.
- B. Nonparametric tests are the tests used on Non-normal Data, so there is no real distinction here.
- C. An F-test is the test of the variances of 2 samples, so the two are the same thing.
Question 59
A Belt is analyzing data and upon creation of the graphical analysis sees multiple modes. One of the primary reasons this could occur is because the process has experienced a ____________________.
- A. Significant change from one shift to another
- B. Sizable Measurement System error
- C. Catastrophic failure of some sort
- D. Any one of these
Show answer and explanation ▾
Correct answer: D
Multiple modes show that the data come from more than one distribution. A change from one shift to another, a large Measurement System error or a major failure can each create a second population in the data.
Why the other options are wrong:
- A. A shift to shift change is only one of the listed causes, so this choice is incomplete.
- B. Measurement System error is only one of the listed causes, so this choice is incomplete.
- C. A catastrophic failure is only one of the listed causes, so this choice is incomplete.
Question 60
Time is always the metric on the horizontal scale of a(n) ___________ Chart.
- A. Pareto
- B. Xbar
- C. Multi-Vari
- D. NP
Show answer and explanation ▾
Correct answer: C
A Multi-Vari Chart is built to show variation within a unit, between units and over time, so time is the metric laid out along its horizontal scale.
Why the other options are wrong:
- A. A Pareto Chart places categories on the horizontal scale, ranked by frequency.
- B. An Xbar Chart places subgroup numbers on the horizontal scale.
- D. An NP Chart places sample numbers on the horizontal scale.
Question 61
To properly analyze the variables impacting the output of a process we need to collect data that represents at least 80% of the variation in the process and assure ourselves we are collecting data from all three types of variation which are _______________.
- A. Within, Between and Temporal
- B. Within, Between and Temporary
- C. Without, Above and Below
- D. Induced, Natural and Unavoidable
Show answer and explanation ▾
Correct answer: A
Multi-Vari analysis groups variation into three types: Within a unit, Between units and Temporal, which is variation over time. Data must cover all three to represent the process properly.
Why the other options are wrong:
- B. Temporary is not the term; variation over time is called Temporal.
- C. Without, Above and Below are not the three types of variation.
- D. Induced, Natural and Unavoidable are not the three types of variation used in this analysis.
Question 62
When the Inputs, X’s, for your process are Normally Distributed about the Mean, the Outputs, Y’s, will always be Normally Distributed.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: B
Normally Distributed inputs do not guarantee a Normally Distributed output. The relationship between the Xs and the Y can be non-linear or involve interactions, which changes the shape of the output distribution.
Why the other options are wrong:
- A. The word always makes the statement untrue, because the transfer function between inputs and output can change the distribution shape.
Question 63
On a _________________ a Belt screens variables, or various inputs, to analyze their relative impact on the output of concern.
- A. X-Y Matrix
- B. Weighted Scale
- C. Multi-Vari Chart
- D. Poisson Chart
Show answer and explanation ▾
Correct answer: C
A Multi-Vari Chart displays how the output changes across several input variables at once, which lets a Belt screen the inputs and see which sources of variation have the largest effect on the output.
Why the other options are wrong:
- A. An X-Y Matrix ranks inputs by team scoring rather than by charting data on their effect.
- B. A Weighted Scale is not a chart for screening input variables.
- D. A Poisson Chart is not a tool for screening input variables.
Question 64
For a Normal Distribution as samples size increases the Range in Mean and Standard Deviation decrease relative to the Mean and Standard Deviation of the population.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
Larger samples give estimates of the Mean and Standard Deviation that sit closer to the true population values, so the spread of those sample estimates shrinks as the sample size grows.
Why the other options are wrong:
- B. Sample estimates become more consistent, not less, as the sample size increases.
Question 65
Some of the sources for different types of error that can be quantified using Statistical Analysis are ___________________.
- A. Error in sampling
- B. Bias in sampling
- C. Error in measurement
- D. All of these answers are correct
Show answer and explanation ▾
Correct answer: D
Statistical Analysis can put a number on sampling error, on bias introduced by how the sample was drawn and on measurement error, so all three listed sources apply.
Why the other options are wrong:
- A. Error in sampling is only one of the listed sources, so this choice is incomplete.
- B. Bias in sampling is only one of the listed sources, so this choice is incomplete.
- C. Error in measurement is only one of the listed sources, so this choice is incomplete.
Question 66
Since Normality is required if we intend to use the data collected as a predictive tool. To test for Normality of data we must determine if the Pvalue is ___________.
- A. Equal to 0.05
- B. Less than 0.05
- C. Greater than 0.05
- D. Greater than 0.5
Show answer and explanation ▾
Correct answer: C
A Normality test takes as its Null Hypothesis that the data are Normal. A P-value greater than 0.05 means that hypothesis is not rejected, so the data can be treated as Normal.
Why the other options are wrong:
- A. The decision rule is not a P-value exactly equal to 0.05.
- B. A P-value less than 0.05 rejects Normality.
- D. The threshold for the test is 0.05, not 0.5.
Question 67
The Normal Distribution is considered to be the most important distribution in statistics and, among other things is defined as having a total area under the curve of 1, is mounded and symmetrical and the Mean, Median and Mode are _____________.
- A. All evenly divisible by 3
- B. Twice the Standard Deviation
- C. Within 10% of each other
- D. The same number
Show answer and explanation ▾
Correct answer: D
A Normal Distribution is perfectly symmetrical around its center, so the Mean, Median and Mode all fall at the same point and have the same value.
Why the other options are wrong:
- A. Divisibility by 3 has nothing to do with the Normal Distribution.
- B. The Mean, Median and Mode have no fixed relationship of twice the Standard Deviation.
- C. In a Normal Distribution the three measures are identical, not merely close.
Question 68
Following process modifications, the Null Hypothesis states that no improvement to the process has occurred. If we discover the Null Hypothesis Test was rejected when it was false that would be a(n) ________________________.
- A. Alpha Error
- B. Type I Error
- C. Type II Error
- D. Type III Error
Show answer and explanation ▾
Correct answer: C
A Type II Error is the error tied to a Null Hypothesis that is false: the process really did improve, but the test does not show it, so a real improvement is missed. The chance of making it is the Beta risk.
Why the other options are wrong:
- A. An Alpha Error involves a Null Hypothesis that is true, not one that is false.
- B. A Type I Error is rejecting a Null Hypothesis that is true.
- D. Type III Error is not one of the two decision errors defined for a Hypothesis Test.
Question 69
A statistical test or Hypothesis Test is performed to reject or fail to reject a stated hypothesis and it converts the Practical Problem into a Statistical Problem.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
A Hypothesis Test turns the Practical Problem into a Statistical Problem by stating a Null and an Alternative Hypothesis. The test result is then to reject or fail to reject the Null Hypothesis.
Why the other options are wrong:
- B. The statement describes correctly what a Hypothesis Test does, so it is not false.
Question 70
How many experimental runs exist in a Full Factorial and fully randomized design for 5 factors with 2 replicates for the Corner Points and no Center Points? The factors in the experiment are only at 2-levels.
- A. 10
- B. 128
- C. 256
- D. 64
Show answer and explanation ▾
Correct answer: D
A Full Factorial for 5 factors at 2 levels has 2 to the power of 5, or 32, corner points. Two replicates of each corner point give 32 x 2 = 64 experimental runs.
Why the other options are wrong:
- A. 10 is 5 factors times 2 levels, which is not how runs are counted.
- B. 128 would need four replicates of the 32 corner points.
- C. 256 is far more than 32 corner points run twice.
Question 71
If an experiment has 5 factors and no replicates for a 2-level Experimental Design with 16 experimental runs which statement(s) are correct? (Note: There are 3 correct answers). (Choose three.)
- A. The Main Effects for the 5 factors are not aliased or confounded but the 2-way interactions are confounded with the 3-way interactions
- B. The Main Effects are confounded with only 4-way interactions
- C. The Experimental Design is half-fractional
- D. The experiment has 8 experimental runs with the first factor at the high level
- E. The experiment has only 4 experimental runs with the 5th factor at the high level
Show answer and explanation ▾
Correct answer: B, C, D
Sixteen runs for 5 two-level factors is half of the 32-run Full Factorial, so the design is half-fractional. In this design each Main Effect is confounded with a 4-way interaction, and every factor sits at its high level in half of the runs, which is 8.
Why the other options are wrong:
- A. The Main Effects are confounded with 4-way interactions, so saying they are not aliased or confounded is untrue.
- E. The 5th factor is at the high level in 8 of the 16 runs, not 4.
Question 72
With Measurement System Analysis we are concerned with two issues that impact the potential variability of the data. They are ____________ and Accuracy.
- A. Spread
- B. Reliability
- C. Precision
- D. Deflection
Show answer and explanation ▾
Correct answer: C
Measurement System Analysis looks at Accuracy, how close measurements are to the true value, and Precision, how close repeated measurements are to each other.
Why the other options are wrong:
- A. Spread is not the named partner of Accuracy in Measurement System Analysis.
- B. Reliability is not the term paired with Accuracy in Measurement System Analysis.
- D. Deflection is not a Measurement System Analysis term.
Question 73
An operator is measuring the distance between two points.
Which is most likely to be influenced by the operator?
- A. Precision of the measurement
- B. Accuracy of the measurement
- C. Calibration of the instrument
- D. All of these answers are correct
Show answer and explanation ▾
Correct answer: D
The operator's technique affects how consistent repeated readings are, how close they come to the true value and how the instrument is set up and calibrated, so all three are open to operator influence.
Why the other options are wrong:
- A. Precision is only one of the things the operator influences, so this choice is incomplete.
- B. Accuracy is only one of the things the operator influences, so this choice is incomplete.
- C. Calibration is only one of the things the operator influences, so this choice is incomplete.
Question 74
Accuracy can be assessed in several ways and a fairly accurate means of measurement is visual comparison.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: B
Visual comparison depends on human judgment and is a weak way to assess Accuracy. Accuracy is assessed by comparing measurements with a known reference standard.
Why the other options are wrong:
- A. Visual comparison is subjective, so it is not a fairly accurate means of measurement.
Question 75
Measurement __________ is defined as the difference between the observed and the expected values for a given set of data.
- A. Breadth
- B. Linearity
- C. Range
- D. Bias
Show answer and explanation ▾
Correct answer: D
Bias is the difference between the average observed measurement and the expected, or reference, value. It shows how far the Measurement System is off target.
Why the other options are wrong:
- A. Breadth is not a Measurement System term.
- B. Linearity describes how Bias changes across the measuring range of the gage.
- C. Range is the difference between the highest and lowest values in a data set.
Question 76
Appropriate measures means that measurements are ______________.
- A. Representative
- B. Sufficient
- C. Contextual
- D. Relevant
- E. All of these answers are correct
Show answer and explanation ▾
Correct answer: E
Appropriate measures are Sufficient in quantity, Relevant to the problem, Representative of the process and Contextual, meaning collected with the related information needed to interpret them. All four listed qualities apply.
Why the other options are wrong:
- A. Representative is only one of the four qualities, so this choice is incomplete.
- B. Sufficient is only one of the four qualities, so this choice is incomplete.
- C. Contextual is only one of the four qualities, so this choice is incomplete.
- D. Relevant is only one of the four qualities, so this choice is incomplete.
Question 77
A ___________ problem in the Measurement System suggests that there is a lack of consistency in the measurement over time.
- A. Linearity
- B. Bias
- C. Stability
- D. Magnitude
Show answer and explanation ▾
Correct answer: C
Stability is the ability of a Measurement System to give the same results on the same items over time. A lack of consistency over time is a Stability problem.
Why the other options are wrong:
- A. Linearity concerns how Bias changes across the measuring range, not over time.
- B. Bias is the offset from the reference value, not a change over time.
- D. Magnitude is not a Measurement System Analysis term.
Question 78
An operator checks that all boxes being packed contain enough products to fill the box. However, each box getting filled has a different number of products in it.
This is a Reproducibility problem, not a Repeatability problem.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: B
Reproducibility is the variation between different operators measuring the same thing. Here a single operator is getting inconsistent results, which is not a Reproducibility problem.
Why the other options are wrong:
- A. Only one operator is involved, so there is no operator to operator variation to call Reproducibility.
Question 79
In a good Measurement System the most variation will be with part-to-part measurements.
What should you do if the majority of variation is associated with the Gage R&R assuming the gage is technically capable?
- A. Focus on fixing the Repeatability and Reproducibility of the measurement device
- B. Purchase a new machine
- C. Focus on trimming the Part-to-Part variation
- D. Run another MSA test with the machine
Show answer and explanation ▾
Correct answer: A
When most of the variation comes from the Gage R&R, the Measurement System cannot be trusted to show real process differences. With a technically capable gage, the fix is to improve the Repeatability and Reproducibility of the measurement.
Why the other options are wrong:
- B. The gage is stated to be technically capable, so buying a new machine is not the response.
- C. Part-to-Part variation is real process variation and is not the fault in the Measurement System.
- D. Repeating the study without fixing anything would return the same result.
Question 80
What aspects of Measurement Systems Analysis (MSA) studies are applicable when the process used to measure does not damage the part?
- A. Destructive variable gage R&R and Crossed Study
- B. Destructive variable gage R&R and Nested Study
- C. Nondestructive variable gage R&R and Crossed Study
- D. Nondestructive variable gage R&R and Nested Study
Show answer and explanation ▾
Correct answer: D
A measurement that leaves the part intact is assessed with a nondestructive variable Gage R&R. A Nested Study is the design used when each operator measures a different set of parts.
Why the other options are wrong:
- A. A destructive study applies when the measurement damages the part, which is not the case here.
- B. A destructive study applies when the measurement damages the part, which is not the case here.
- C. A Crossed Study is not the pairing identified here for this measurement process.
Question 81
Each of the items listed would impact the Process Capability for a process with a continuous output except ___________________.
- A. Shape of process data distribution (e.g. Normal Distribution)
- B. Process Technology
- C. Process Standard Deviation
- D. Seasonal variation in process
Show answer and explanation ▾
Correct answer: B
Process Capability for a continuous output is calculated from the data: the shape of the distribution, the Standard Deviation and shifts such as seasonal variation all change the result. Process Technology is not an input to the calculation.
Why the other options are wrong:
- A. The shape of the distribution determines which Capability calculation is valid and what it returns.
- C. The Standard Deviation is in the denominator of the Capability indices.
- D. Seasonal variation widens long term variation and lowers Capability.
Question 82
For Attribute Data, Process Capability is defined as the average proportion of nonconforming products.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
Attribute Data has no Mean and Standard Deviation to compare with specification limits, so Capability is expressed as the average proportion of nonconforming product.
Why the other options are wrong:
- B. The average proportion nonconforming is the accepted measure of Capability for Attribute Data.
Question 83
The reported Cpk for a process with an average of 104 units, a spread of 18 units and upper and lower specification limits of 122 and 96 units would be?
- A. 0.5
- B. 0.89
- C. 1.00
- D. 2.00
Show answer and explanation ▾
Correct answer: B
A spread of 18 units is six Standard Deviations, so three Standard Deviations is 9. The distance to the upper limit is 18, giving 2.00, and the distance to the lower limit is 8, giving 0.89. Cpk is the smaller of the two, 0.89.
Why the other options are wrong:
- A. 0.5 does not result from either specification limit.
- C. 1.00 does not result from either specification limit.
- D. 2.00 is the value against the upper limit, and Cpk reports the smaller value.
Question 84
When we compare short-term and long-term Capability which of these is true?
- A. Cp is better for the short term
- B. Both short-term and long-term performance are alike
- C. Performance tends to improve over time
- D. Cp is better for the long-term
Show answer and explanation ▾
Correct answer: A
Short-term data captures only common cause variation, so the Standard Deviation is smaller and Cp looks better. Over the long term, shifts and drifts add variation and Capability falls.
Why the other options are wrong:
- B. Long-term data includes more sources of variation, so the two are not alike.
- C. Capability tends to look worse, not better, as more variation is captured over time.
- D. Long-term variation is larger, so Cp is not better for the long term.
Question 85
Relative to a Design of Experiments the term Collinear refers to variables being a ________________ of each other.
- A. Linear combination
- B. Directly parallel
- C. Mirror image
- D. None of the above
Show answer and explanation ▾
Correct answer: A
Collinear variables are a linear combination of each other, which means one can be predicted from the others. Their effects on the response cannot be separated in the analysis.
Why the other options are wrong:
- B. Directly parallel is not the definition of Collinear in a Design of Experiments.
- C. This phrase does not describe what Collinear means in a Design of Experiments.
- D. One of the listed choices does define the term, so None of the above does not apply.
Question 86
The Lean toolbox includes all of the following items except __________.
- A. Poke-Yoke
- B. Standard Operating Procedures
- C. Kaizen
- D. 5S the work area
Show answer and explanation ▾
Correct answer: B
Poka-Yoke, Kaizen and 5S are named Lean tools. Standard Operating Procedures are general process documentation used in any management system and are not a tool specific to the Lean toolbox.
Why the other options are wrong:
- A. Poka-Yoke, or Mistake Proofing, is a Lean tool.
- C. Kaizen is a Lean tool for rapid improvement.
- D. 5S is a Lean tool for workplace organization.
Question 87
If a Six Sigma project was to reduce changeover times and the team found the project success was decreasing over time since changeover times began to creep back up, which Lean tools should be considered in the Control Phase to reestablish and sustain the project success?
- A. Improve the lighting to assure adequate visibility
- B. Confirm a Visual Factory exists to assure proper communication of status of machines
- C. Implement Kanbans to assure enough inventory for the process step
- D. Reword the standardized work instructions to use active verbs and not passive phrases
Show answer and explanation ▾
Correct answer: B
A Visual Factory makes the status of machines and changeovers obvious at a glance, so drift from the improved method is noticed and corrected quickly. That visibility is what sustains a changeover time improvement in the Control Phase.
Why the other options are wrong:
- A. Better lighting is not a Lean tool and does not control changeover times.
- C. Kanbans manage replenishment of inventory and do not address changeover times.
- D. Rewording instructions is not a Lean control tool and does not show when changeovers slip.
Question 88
Kaizens or Kaikakus and Six Sigma projects are intended to create breakthrough, significant process improvement versus minor, incremental improvements.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
Kaikaku means radical change, and Six Sigma projects target breakthrough results. These efforts are aimed at significant process improvement instead of small adjustments.
Why the other options are wrong:
- B. These improvement efforts are aimed at significant gains, so the statement is not false.
Question 89
Which of these items are not part of what is necessary for successful Kaizens?
- A. Good lighting
- B. Management support
- C. Operator support
- D. Analysis tools
Show answer and explanation ▾
Correct answer: A
A successful Kaizen needs Management support, Operator support and Analysis tools. Good lighting is a workplace condition and is not one of the requirements for a Kaizen.
Why the other options are wrong:
- B. Management support is needed to provide time, people and authority for the Kaizen.
- C. Operator support is needed because the operators run and sustain the changed process.
- D. Analysis tools are needed to find and confirm the improvements.
Question 90
For a Kanban to be successful which of these must occur?
- A. Consistent cycle times
- B. Fairly stable process demand of product or service
- C. Low defect rate of incoming product or service
- D. All of the above
Show answer and explanation ▾
Correct answer: D
A Kanban works with small, fixed quantities, so it needs consistent cycle times, fairly stable demand and a low defect rate in what arrives. If any one of these is missing the system runs short or overfills.
Why the other options are wrong:
- A. Consistent cycle times is only one of the listed conditions, so this choice is incomplete.
- B. Stable demand is only one of the listed conditions, so this choice is incomplete.
- C. A low incoming defect rate is only one of the listed conditions, so this choice is incomplete.
Question 91
Common and Special Cause ______________ are the focus of Statistical Process Control.
- A. Prediction
- B. Ideation
- C. Capability
- D. Variation
Show answer and explanation ▾
Correct answer: D
Statistical Process Control separates Common Cause Variation, which is always present, from Special Cause Variation, which signals that something has changed. Variation is the focus.
Why the other options are wrong:
- A. Prediction is not a type of Common and Special Cause.
- B. Ideation is idea generation and is not what SPC monitors.
- C. Capability compares the process with specifications and is not classified as Common or Special Cause.
Question 92
If you can Poka-Yoke a defect out of the process entirely then you do not need use SPC on the characteristic of interest in the defect.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
A Poka-Yoke that removes the defect entirely means the defect can no longer occur. There is nothing left for an SPC chart to monitor on that characteristic.
Why the other options are wrong:
- B. Once the defect cannot occur, charting that characteristic adds no control.
Question 93
Range Charts are the technique used to determine if ______________ are occurring within the subgroups of the SPC Charts.
- A. Common Causes
- B. Special inspections
- C. Unnatural forces
- D. Special Causes
Show answer and explanation ▾
Correct answer: D
A Range Chart plots the variation inside each subgroup. Points beyond its control limits show that Special Causes are acting within the subgroups.
Why the other options are wrong:
- A. Common Causes are always present; the Range Chart is used to detect the unusual ones.
- B. Special inspections is not an SPC term.
- C. Unnatural forces is not an SPC term.
Question 94
If a process has subgroups for Variable data and the process runs for a long period of time, then the best pair of SPC Charts to use would be an Xbar and _________.
- A. NP Chart
- B. Individuals Chart
- C. R Chart
- D. C Chart
Show answer and explanation ▾
Correct answer: C
Variable data collected in subgroups is tracked with an Xbar Chart for the subgroup average and an R Chart for the subgroup range. The pair monitors both the center and the spread of the process.
Why the other options are wrong:
- A. An NP Chart is for Attribute data, counting defective items.
- B. An Individuals Chart is for data collected one value at a time, without subgroups.
- D. A C Chart is for Attribute data, counting defects.
Question 95
Six Sigma is a business improvement discipline whose fundamental view is based on a _________ oriented approach of the business.
- A. Profit
- B. Performance
- C. Process
- D. Predatory
Show answer and explanation ▾
Correct answer: B
Six Sigma takes a performance oriented view of the business: it measures how well the business performs against customer requirements and drives improvement from those measures.
Why the other options are wrong:
- A. Profit is a result of the improvement, not the orientation of the approach.
- C. Process is not the word that completes this definition of the Six Sigma view.
- D. Predatory has no place in the definition of Six Sigma.
Question 96
Much of the Six Sigma methodology is used to identify and remove causes for _____________ .
- A. Process Variation
- B. Material Costs
- C. Excess Inventory
- D. Lost Sales
Show answer and explanation ▾
Correct answer: A
Six Sigma methods are designed to find and remove the causes of Process Variation, because variation is what produces defects and inconsistent results for the customer.
Why the other options are wrong:
- B. Lower material costs can follow from a project but are not what the methodology is built to remove.
- C. Excess inventory is a waste addressed by Lean tools, not the main target of Six Sigma methods.
- D. Lost sales are a business result, not a cause that the methodology removes.
Question 97
When variation is removed from the output of a process then the process customer can have more confidence in the experience that results from the process.
- A. True
- B. False
Show answer and explanation ▾
Correct answer: A
Less variation in the output means the customer receives a more consistent, predictable result each time, which builds confidence in the process.
Why the other options are wrong:
- B. Removing variation makes the output more predictable for the customer, so the statement is not false.
Question 98
The distance between the Mean of a data set and the Point of Inflection on a Normal curve is called the _______________.
- A. Curve Spread
- B. Standard Deviation
- C. Numerical Average
- D. Data Breadth
Show answer and explanation ▾
Correct answer: B
On a Normal curve the Point of Inflection, where the curve changes from bending downward to bending upward, lies exactly one Standard Deviation from the Mean.
Why the other options are wrong:
- A. Curve Spread is not the name of this distance.
- C. The Numerical Average is the Mean itself, not a distance from it.
- D. Data Breadth is not a statistical term for this distance.
Question 99
One of the foundations of Lean Six Sigma is the concept that the output of a process (Y) is influenced by the process inputs (Xs) and is commonly shown as which formula?
- A. Y = Z(X2)
- B. Y = f(X3)
- C. Y = f(Xn)
- D. Y = g(X+ 1.5)
Show answer and explanation ▾
Correct answer: C
The output Y is a function of all the process inputs, written Y = f(Xn), where n stands for the number of inputs X1, X2 and so on.
Why the other options are wrong:
- A. Y = Z(X2) is not the form used to show the output as a function of the inputs.
- B. Y = f(X3) names a single input, not the full set of inputs.
- D. Y = g(X+ 1.5) is not the form used to show the output as a function of the inputs.
Question 100
When we gather information for the Voice of the Business we are primarily interested in information concerning the _____________ of the business.
- A. Advertising budget
- B. Market share
- C. Profitability
- D. Ownership
Show answer and explanation ▾
Correct answer: C
The Voice of the Business expresses what the business itself needs from its processes, which centers on financial results and Profitability.
Why the other options are wrong:
- A. The advertising budget is a single spending item, not the main concern of the Voice of the Business.
- B. Market share is not the primary information gathered for the Voice of the Business.
- D. Ownership of the business is not what the Voice of the Business describes.
Question 101
When a Belt creates a Process Map she will use a __________________ to depict a decision point requiring a Yes or No decision.
- A. Circle
- B. Square
- C. Diamond
- D. Rectangle
Show answer and explanation ▾
Correct answer: C
On a Process Map a Diamond marks a decision point. The flow leaves the Diamond along one path for Yes and another for No.
Why the other options are wrong:
- A. A Circle is not the symbol for a Yes or No decision.
- B. A Square is not the symbol for a Yes or No decision.
- D. A Rectangle marks a process step or activity.
Question 102
A Belt has determined that the inventory of repair parts at a rework station can be reduced by 45%. According to Cost of Poor Quality (COPQ) definitions inventory reduction would be considered _______________.
- A. Soft Savings
- B. COPQ efficiency
- C. Median Savings
- D. Hard Savings
Show answer and explanation ▾
Correct answer: D
Cutting inventory frees cash and lowers carrying cost in a way that can be measured on the financial statements, which makes it Hard Savings.
Why the other options are wrong:
- A. Soft Savings are benefits that cannot be traced directly to the financial statements.
- B. COPQ efficiency is not a savings category.
- C. Median Savings is not a savings category.
Question 103
Customers make their decisions based on Features, Integrity (of the seller) Delivery and ___________?
- A. Color
- B. Expense
- C. Season
- D. None
Show answer and explanation ▾
Correct answer: B
Customers judge value on four things: Features, Integrity of the seller, Delivery and Expense, where Expense is what the purchase costs them.
Why the other options are wrong:
- A. Color is a product feature, which is already covered by Features.
- C. Season is not one of the four decision factors.
- D. A fourth factor does exist, so None does not apply.
Question 104
The Hardware Store ordered ten lawn mower from the manufacturer and just before shipping the manufacturer found one to have a motor that wouldnt start. For the manufacturer this would be categorized as what type of cost?
- A. Internal Failure Costs
- B. External Failure Costs
- C. Prevention Costs
- D. Appraisal Costs
Show answer and explanation ▾
Correct answer: A
A defect that the producer finds before the product ships to the customer is an internal failure cost. The manufacturer caught the mower with the motor that would not start while it was still in its own hands, so the cost of fixing or scrapping it stays inside the business.
Why the other options are wrong:
- B. External failure costs arise only after the product has reached the customer, and this mower had not shipped.
- C. Prevention costs are spent to stop defects from happening, such as training and process design, not on a defect that already exists.
- D. Appraisal costs are the costs of inspecting and testing, not the cost of the defective unit that the inspection finds.
Question 105
Cost of Poor Quality (COPQ) can be classified as Visible Costs and Hidden Costs. All these items are Hidden Cost except __________________.
- A. Lost Customer Loyalty
- B. Returns
- C. Time Value of Money
- D. Late Delivery
Show answer and explanation ▾
Correct answer: B
Returns are a visible cost of poor quality because they are counted and reported in the normal accounts, alongside scrap, rework and warranty claims. Hidden costs are the ones that standard reports do not capture.
Why the other options are wrong:
- A. Lost customer loyalty is a hidden cost because the future sales it removes do not show up in the accounts.
- C. The time value of money tied up by poor quality is a hidden cost that standard reports do not track.
- D. Late delivery is a hidden cost because its effect on customers and cash flow is rarely measured directly.
Question 106
Which of these are examples of business metrics or Key Performance Indicators commonly referred to as KPI’s?
- A. Cycle Time
- B. Defects
- C. No. of Units Reworked
- D. Labor Hours
- E. All of these answers are correct
Show answer and explanation ▾
Correct answer: E
Cycle time, defects, the number of units reworked and labor hours are all measures a business tracks to judge how well a process performs, so each one can serve as a KPI.
Why the other options are wrong:
- A. Cycle time is a common KPI, but it is only one of the listed metrics that qualify.
- B. Defects are a common KPI, but the other listed metrics qualify as well.
- C. The number of units reworked is a KPI, but it is not the only one listed.
- D. Labor hours are a KPI, but the other listed metrics qualify as well.
Question 107
When one speaks of 20% of something contributing 80% of the affect they are referring to what is known as the _________________.
- A. Shewhart Example
- B. Pareto Principle
- C. Balance Equation
- D. Connection Principle
Show answer and explanation ▾
Correct answer: B
The Pareto Principle, also called the 80/20 rule, states that roughly 80% of an effect comes from about 20% of the causes. Six Sigma teams use it to focus on the vital few causes instead of the trivial many.
Why the other options are wrong:
- A. Shewhart is associated with control charts and the Plan-Do-Check-Act cycle, not with the 80/20 rule.
- C. Balance Equation is not the name of the 80/20 relationship.
- D. Connection Principle is not a recognized term for the 80/20 relationship.
Get the complete ICBB bank
These 107 questions are roughly 33% of the bank. The full pack has 324 real exam questions, each with the same depth of explanation, plus a questions-only PDF for timed practice and free updates forever.
View the full IASSC ICBB question bank →
About the ICBB exam
These 107 IASSC ICBB questions are free here. The free sample PDF has 119.