GAQM CLSSBB Practice Questions with Explanations

Free GAQM CLSSBB practice questions. 89 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.

CLSSBB practice questions

Question 1

A ___________ is used primarily to track the stability of the average value of a metric of interest.

  • A. NP Chart
  • B. Xbar-R Chart
  • C. I-MR Chart
  • D. C Chart
Show answer and explanation ▾

Correct answer: B

An Xbar-R chart plots the average of each sample, together with the sample range, so it shows whether the average of a metric is stable over time.

Why the other options are wrong:

  • A. An NP chart tracks the count of defectives, not the average of a measurement.
  • C. An I-MR chart plots individual values and moving ranges, not sample averages.
  • D. A C chart counts defects per unit, not average values.

Question 2

For her injection molding project a Belt needed to track the percentage of defectives of a particular sample set so she used a ___________ to display the data?

  • A. Individual Chart
  • B. C Chart
  • C. Xbar Chart
  • D. P Chart
Show answer and explanation ▾

Correct answer: D

A P chart tracks the proportion or percentage of defective items in a sample, which is what the belt needed for her injection molding data.

Why the other options are wrong:

  • A. An individual chart plots single measurements, not a percentage of defectives.
  • B. A C chart counts the number of defects, not the share of defective units.
  • C. An Xbar chart plots sample averages of continuous data.

Question 3

Control Charts were developed by Dr. Shewhart to track data over time. To detect Special Cause variation the Control Charts use which of these?

  • A. Data shift analysis
  • B. Outlier analysis methods
  • C. Center Line and Control Limits
  • D. None of the above
Show answer and explanation ▾

Correct answer: C

Control charts show the process average as a center line, with control limits either side. A point beyond the limits, or a pattern within them, signals special cause variation.

Why the other options are wrong:

  • A. Data shift analysis is not the method control charts use to detect special causes.
  • B. Outlier analysis is not the mechanism control charts are built on.
  • D. The center line and control limits do provide the means, so this is incorrect.

Question 4

Common and ______________ Cause Variation are the focus of Statistical Process Control.

  • A. Uncommon
  • B. Ordinary
  • C. Special
  • D. Selective
Show answer and explanation ▾

Correct answer: C

Statistical process control separates common cause variation, which is natural to the process, from special cause variation, which comes from specific events and can be removed.

Why the other options are wrong:

  • A. Uncommon is not a standard term for a type of variation.
  • B. Ordinary is not the standard term, and it would only restate common cause.
  • D. Selective is not a standard term for a type of variation.

Question 5

Special Cause Variation falls into which two categories?

  • A. Natural & Unnatural
  • B. Short Term & Long Term
  • C. Assignable & Pattern
  • D. Attribute & Discreet
Show answer and explanation ▾

Correct answer: C

Special Cause Variation is split into Assignable causes, which can be traced to a specific source, and Pattern causes, which show up as non-random patterns such as trends, shifts or cycles in the data.

Why the other options are wrong:

  • A. Natural variation is another name for Common Cause Variation, not a category of Special Cause.
  • B. Short Term and Long Term describe time frames for capability, not categories of Special Cause.
  • D. Attribute and Discrete are types of data, not categories of variation.

Question 6

Range Charts are the technique used to determine if Special Causes are occurring within the subgroups of the ______________.

  • A. Histograms
  • B. SPC Charts
  • C. NP Charts
  • D. Pareto Charts
Show answer and explanation ▾

Correct answer: B

A Range Chart plots the range within each subgroup of an SPC Chart, so it shows whether Special Causes are acting on the within-subgroup variation.

Why the other options are wrong:

  • A. Histograms show the shape of a distribution and have no subgroups tracked over time.
  • C. NP Charts track counts of defective units, not ranges within subgroups.
  • D. Pareto Charts rank categories by frequency and have no subgroups.

Question 7

If the production is for higher volume and monitoring and the Mean and variability is to be monitored for four machines producing product and the characteristic to be monitored is Variable Data, which SPC Chart is best to be selected?

  • A. Xbar-R Chart
  • B. Individual-MR Chart
  • C. NP Chart
  • D. CUSUM Chart
Show answer and explanation ▾

Correct answer: A

With Variable Data and high volume, samples can be taken in subgroups, and an Xbar-R Chart tracks both the Mean (Xbar) and the variability (Range) of those subgroups.

Why the other options are wrong:

  • B. An Individual-MR Chart suits low volume processes where only one reading is available at a time.
  • C. An NP Chart is for Attribute Data, counting defective units.
  • D. A CUSUM Chart is aimed at detecting small shifts in the Mean, not at routine monitoring of Mean and variability together.

Question 8

When a Belt Poka-Yoke’s a defect out of the process entirely then she should track the activity with a robust SPC system on the characteristic of interest in the defect as an early warning system.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: B

Once Poka-Yoke has removed a defect from the process entirely, the defect can no longer occur, so there is nothing left for an SPC system to warn about. SPC is used where defects can still happen.

Why the other options are wrong:

  • A. A defect that has been mistake proofed out of the process does not need an SPC early warning system.

Question 9

Following the completion of a LSS project the Belt not only creates a Control Plan he also develops a _____________ so those involved in the process know what to do when the critical metrics move out of spec.

  • A. Response Plan
  • B. Call List
  • C. Chain-of-Command
  • D. Defect Analysis Plan
Show answer and explanation ▾

Correct answer: A

A Response Plan goes with the Control Plan and tells the people running the process exactly what to do when a critical metric moves out of spec or out of control.

Why the other options are wrong:

  • B. A Call List only names who to contact and does not say what action to take.
  • C. A Chain-of-Command describes reporting lines, not the actions to take on the process.
  • D. Defect Analysis Plan is not the document that guides the reaction to out of spec metrics.

Question 10

The Control Limits width varies if the sample size varies for which type of chart?

  • A. P Charts
  • B. NP Charts
  • C. Xbar-R Charts
  • D. Time Series Charts
Show answer and explanation ▾

Correct answer: A

A P Chart plots the proportion defective and allows the sample size to change. Its Control Limits are calculated from each sample size, so they widen for small samples and narrow for large ones.

Why the other options are wrong:

  • B. NP Charts require a constant sample size, so their Control Limits stay the same width.
  • C. Xbar-R Charts are run with a fixed subgroup size, giving constant Control Limits.
  • D. Time Series Charts have no Control Limits at all.

Question 11

Which of these elements are not included in Implementation plans?

  • A. Work breakdown structure
  • B. Risk management plans
  • C. Cost/Benefit ratios
  • D. Planned audits of work completion
Show answer and explanation ▾

Correct answer: C

Cost/Benefit ratios are worked out earlier, when solutions are being selected and justified. The Implementation plan covers how the chosen solution is rolled out: the tasks, the risks and the checks on completed work.

Why the other options are wrong:

  • A. A work breakdown structure is a standard part of an Implementation plan.
  • B. Risk management plans are a standard part of an Implementation plan.
  • D. Planned audits of work completion are a standard part of an Implementation plan.

Question 12

Upon completion and validation of an improvement to a process a Belt and the Project Team create a Control Plan that contains which of these?

  • A. Standard operating work description of the process change
  • B. Description of the monitoring system in place to assure continued compliance
  • C. Summary of the targeted critical metrics for process performance measurement
  • D. All of the above
Show answer and explanation ▾

Correct answer: D

A Control Plan documents how the improved process is run and kept in control, so it includes the standard work for the change, the monitoring system and the critical metrics with their targets.

Why the other options are wrong:

  • A. The standard work description is only one of the items a Control Plan contains.
  • B. The monitoring system description is only one of the items a Control Plan contains.
  • C. The summary of critical metrics is only one of the items a Control Plan contains.

Question 13

How many experimental runs exist in a Full Factorial and fully randomized design for 4 factors with 2 replicates for the Corner Points and no Center Points? The factors in the experiment are only at 2-levels.

  • A. 10
  • B. 32
  • C. 256
  • D. 64
Show answer and explanation ▾

Correct answer: B

A 2-level Full Factorial with 4 factors has 2 x 2 x 2 x 2 = 16 corner points. Two replicates of each corner point gives 16 x 2 = 32 runs.

Why the other options are wrong:

  • A. 10 is not the result of 2 to the power of 4, multiplied by 2 replicates.
  • C. 256 is far more runs than 16 corner points with 2 replicates.
  • D. 64 would need 5 factors with 2 replicates, or 4 replicates of this design.

Question 14

If an experiment has 5 factors and no replicates for a 2-level Experimental Design with 16 experimental runs which statement is incorrect?

  • A. The Experimental Design is half-fractional
  • B. The Main Effects are confounded with only 4-way interactions
  • C. The Main Effects for the 5 factors are not aliased or confounded but the 2-way interactions are confounded with the 3-way interactions
  • D. The experiment has 8 experimental runs with the first factor at the high level
Show answer and explanation ▾

Correct answer: C

Five factors in 16 runs is a half fraction (2 to the power of 5 minus 1) with Resolution V. In that design every Main Effect is confounded with a 4-way interaction, so saying the Main Effects are not aliased or confounded at all is the incorrect statement.

Why the other options are wrong:

  • A. A Full Factorial for 5 factors has 32 runs, so 16 runs is a half fraction.
  • B. In this Resolution V design each Main Effect is confounded with a 4-way interaction.
  • D. Each factor is at the high level in half of the 16 runs, which is 8 runs.

Question 15

Fractional Factorial, ____________and Response Surface Method are types of planned experiments.

  • A. Multi-Vari Analysis
  • B. Baldridge Channels
  • C. One Factor at a Time or OFAT
  • D. Factorial Design
Show answer and explanation ▾

Correct answer: D

Full Factorial Design, Fractional Factorial and Response Surface Method are the main families of planned experiments, where factor levels are set deliberately according to a design.

Why the other options are wrong:

  • A. Multi-Vari Analysis is a passive study of existing variation, not a planned experiment.
  • B. Baldridge Channels is not a type of experimental design.
  • C. One Factor at a Time changes inputs one by one and is not a designed experiment of this family.

Question 16

Relative to a Design of Experiments the term ________________ refers to variables being a linear combination of each other.

  • A. Mirror Image
  • B. Directly Parallel
  • C. Collinear
  • D. None of the above
Show answer and explanation ▾

Correct answer: C

Variables are Collinear when one can be written as a linear combination of the others. Collinear factors cannot be separated in the analysis, so their effects cannot be estimated independently.

Why the other options are wrong:

  • A. That is not the term for variables that are a linear combination of each other.
  • B. Directly Parallel is not the term used in Design of Experiments for this condition.
  • D. One of the listed terms, Collinear, is the correct one.

Question 17

Which statement(s) are incorrect about Fractional Factorial Designs?

  • A. A Half Fractional Design for 5 factors has the same number of experimental runs as a Full Factorial Design for 4 factors assuming no repeats or replicates or Center Points
  • B. Quarter Fractional experiments can exist for those with 4 factors
  • C. Resolution V design is desired while controlling costs of experimentation
  • D. Half Fractional experiments do not exist for those designs with only 2 factors
Show answer and explanation ▾

Correct answer: C

Fractional Factorial Designs save cost by giving up resolution. Resolution V needs more runs than Resolution III or IV, so it is not the design to aim for when the goal is to control the cost of experimentation.

Why the other options are wrong:

  • A. A half fraction of 5 factors and a Full Factorial of 4 factors both have 16 runs.
  • B. A quarter fraction of 4 factors works out to 2 to the power of 4 minus 2, which is 4 runs.
  • D. A half fraction of 2 factors would leave only 2 runs, which cannot separate the two factors.

Question 18

If in an experiment all possible variable pairs sum to zero the design is Orthogonal.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

A design is Orthogonal when, for every pair of factor columns, the products of the coded levels sum to zero. This balance lets each effect be estimated independently of the others.

Why the other options are wrong:

  • B. Variable pairs summing to zero is exactly the test for an Orthogonal design.

Question 19

Which Experimental Design typically is most associated with the fewest number of input variables or factors in the design?

  • A. Fractional Factorial design
  • B. Full Factorial design
  • C. Simple Linear Regression
  • D. Response Surface Design
Show answer and explanation ▾

Correct answer: D

Response Surface Designs are used late in experimentation, after screening has cut the list down to the few vital factors, because they need extra runs per factor to model curvature.

Why the other options are wrong:

  • A. Fractional Factorial designs are used to screen a large number of factors.
  • B. Full Factorial designs typically handle more factors than a Response Surface Design.
  • C. Simple Linear Regression is an analysis method, not an Experimental Design.

Question 20

The method of Steepest Ascent guides you toward a target inside the original inference space.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: B

The method of Steepest Ascent moves the experiment along the path of fastest improvement, which leads toward an optimum outside the original inference space, not inside it.

Why the other options are wrong:

  • A. Steepest Ascent is used to move beyond the region first studied, not to stay inside it.

Question 21

Situation where standardized work needs to be incorporated include all of these except ____________________.

  • A. Machines continually operating to reduce the labor cost per piece
  • B. Lack of a system to assure proper inventory levels at repair stations
  • C. Changeover instructions incomplete
  • D. Process flow for the same product assembly taking various cycle time for completion
Show answer and explanation ▾

Correct answer: A

Running machines continually to cut the labor cost per piece is a production scheduling choice that leads to overproduction. It is not a problem of people doing a task in different ways, which is what standardized work fixes.

Why the other options are wrong:

  • B. A missing system for inventory levels at repair stations is a case for standardized work.
  • C. Incomplete changeover instructions are a case for standardized work.
  • D. Varying cycle times for the same assembly are a case for standardized work.

Question 22

The Lean toolbox includes all of these items except ________________.

  • A. Mistake Proofing
  • B. Visual Factory
  • C. Design of Experiments
  • D. Inventory Management
Show answer and explanation ▾

Correct answer: C

Design of Experiments is a statistical Six Sigma tool used in the Improve Phase. Mistake Proofing, Visual Factory and Inventory Management are all part of the Lean toolbox.

Why the other options are wrong:

  • A. Mistake Proofing is a core Lean tool.
  • B. Visual Factory is a core Lean tool.
  • D. Inventory Management is part of Lean, which targets excess inventory as a waste.

Question 23

Questions that can be best answered by a Visual Factory include all of these except _____________________.

  • A. Are downtime issues easily noted?
  • B. Can extra inventory be seen easily?
  • C. Are unneeded tools or supplies easily noted?
  • D. Are setups optimized for lower scrap levels?
Show answer and explanation ▾

Correct answer: D

A Visual Factory makes the status of the workplace obvious at a glance: downtime, extra inventory, unneeded tools. Whether setups are optimized for scrap needs data analysis and cannot be judged by looking.

Why the other options are wrong:

  • A. Downtime issues are made visible by a Visual Factory.
  • B. Extra inventory is made visible by a Visual Factory.
  • C. Unneeded tools or supplies are made visible by a Visual Factory.

Question 24

If a Six Sigma project was to reduce repair station inventory and the team found the inventory was creeping up over time which Lean tools should be considered in the Control Phase to reestablish and sustain the project success?

  • A. Review the Visual Factory to assure inventory in excess of desired visible
  • B. Improve the lighting to assure adequate visibility
  • C. Analyze data from supplier deliveries
  • D. Reword the standardized work instructions to use active verbs and not passive phrases
Show answer and explanation ▾

Correct answer: A

Inventory creeping up means the excess is not being noticed. Reviewing the Visual Factory so that any inventory above the desired level is immediately visible restores the control and sustains the gain.

Why the other options are wrong:

  • B. Better lighting does not show whether inventory is above the desired level.
  • C. Supplier delivery data is an analysis activity, not a Lean control for repair station inventory.
  • D. Changing verb forms in work instructions does not address rising inventory.

Question 25

When a Belt implements an improvement that is automated thus requiring no particular understanding for use he has applied which Lean tool?

  • A. Mistake Proofing
  • B. Kaizen Event
  • C. 5S
  • D. None
Show answer and explanation ▾

Correct answer: A

Mistake Proofing builds the control into the process so that it works automatically. The operator needs no special knowledge because the design itself prevents the error.

Why the other options are wrong:

  • B. A Kaizen Event is a short team improvement activity, not an automated control.
  • C. 5S organizes the workplace and depends on people following it.
  • D. A Lean tool has been applied, and it is Mistake Proofing.

Question 26

Kaizens or Kaikakus and Six Sigma projects are intended to create incremental process improvements versus breakthrough, significant improvements.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: B

Kaizen is aimed at incremental improvement, but Kaikaku and Six Sigma projects are aimed at breakthrough, significant improvement. Grouping all three as incremental makes the statement false.

Why the other options are wrong:

  • A. Kaikaku and Six Sigma projects target breakthrough improvement, not incremental change.

Question 27

Which of these items contribute to what is necessary for successful Kaizen events?

  • A. Analysis tools
  • B. Management support
  • C. Operator support
  • D. All of these answers are correct
Show answer and explanation ▾

Correct answer: D

A successful Kaizen event needs analysis tools to find the improvement, management support to give time and resources, and operator support because operators run the process and carry the change forward.

Why the other options are wrong:

  • A. Analysis tools are only one of the needs listed.
  • B. Management support is only one of the needs listed.
  • C. Operator support is only one of the needs listed.

Question 28

Kanban establishes a means of monitoring production, conveyance and delivery information such that efficient flow is established. The method used by Kanban is to require a _________ before anything moves.

  • A. Sign-off
  • B. Signal
  • C. Bell to ring
  • D. Work order
Show answer and explanation ▾

Correct answer: B

Kanban is a pull system. Nothing is produced or moved until a signal, such as a card or an empty bin, shows that the downstream step needs it.

Why the other options are wrong:

  • A. A sign-off is an approval step, not the trigger used in Kanban.
  • C. Kanban does not require a bell, and its triggers are usually cards or empty bins.
  • D. A work order pushes work by schedule, which is the opposite of the Kanban pull.

Question 29

When a Belt decides to use written procedures and visual controls to improve the consistency of the tasks that must occur in the process he is improving he has utilized the _________________ activity of 5S.

  • A. Sustaining
  • B. Sorting
  • C. Standardizing
  • D. Straightening
Show answer and explanation ▾

Correct answer: C

Standardizing is the 5S activity that sets written procedures and visual controls so tasks are done the same way every time.

Why the other options are wrong:

  • A. Sustaining is about keeping the 5S discipline going over time.
  • B. Sorting removes items that are not needed in the work area.
  • D. Straightening arranges needed items so they are easy to find and use.

Question 30

Fractional Factorial designs are used to reduce the ____________ because the number of runs has been lowered.

  • A. Time and cost of experiments
  • B. Number of people involved
  • C. Number of data measurement points
  • D. Output summary
Show answer and explanation ▾

Correct answer: A

A Fractional Factorial runs only a fraction of the full set of combinations. Fewer runs means less time and lower cost for the experiment.

Why the other options are wrong:

  • B. The number of people involved is not what a Fractional Factorial is designed to reduce.
  • C. The design is chosen to save the time and cost of experimenting, not to cut measurement points as a goal.
  • D. The output summary is not what the design is meant to reduce.

Question 31

Fractional Factorial Designs are used to analyze factors to model the output as a function of inputs if Hypothesis Testing in the Analyze Phase was inadequate to sufficiently narrow the factors that significantly impact the output(s).

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

When Hypothesis Testing in the Analyze Phase has not narrowed the inputs enough, a Fractional Factorial Design lets the Belt test many factors in few runs and model the output as a function of the inputs.

Why the other options are wrong:

  • B. Narrowing down many remaining factors efficiently is exactly what Fractional Factorial Designs are used for.

Question 32

A Factorial Experiment based on a Level 2 Design with 6 factors would require 16 runs to fully assess the interactions.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: B

A 2-level design with 6 factors needs 2 to the power of 6, which is 64 runs, to assess all interactions. Sixteen runs would be a quarter fraction, with interactions confounded.

Why the other options are wrong:

  • A. Sixteen runs cover only a quarter of the 64 combinations, so the interactions cannot be fully assessed.

Question 33

A Full Factorial experiment using a 3 level 3 factor approach has been proposed to test the viability of an extrusion machine experiment.

How many treatment combinations will this approach involve?

  • A. 6
  • B. 9
  • C. 27
  • D. 54
Show answer and explanation ▾

Correct answer: C

A Full Factorial has levels to the power of factors combinations. Three levels and three factors gives 3 x 3 x 3 = 27 treatment combinations.

Why the other options are wrong:

  • A. 6 is 3 plus 3, not 3 to the power of 3.
  • B. 9 is 3 x 3, which covers only two factors at three levels.
  • D. 54 is double the 27 combinations of a single replicate.

Question 34

Screening experiments are the proper choice when a Belt is faced with the situation of highly Fractional Factorial Designs.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

Screening experiments use highly Fractional Factorial Designs to test many factors in very few runs, so the Belt can find the vital few factors before running more detailed experiments.

Why the other options are wrong:

  • B. Highly Fractional Factorial Designs are the standard form of a screening experiment.

Question 35

A valid mathematical Regression represents all of the characteristics shown except ___________________________.

  • A. The residuals when plotted follow a Normal Distribution
  • B. The sum of the residuals is zero
  • C. All of the standardized residuals will be within ±3 Standard Deviations
  • D. Most standardized residuals are within ±2 Standard Deviations
Show answer and explanation ▾

Correct answer: A

The least squares fit itself makes the residuals sum to zero, and in a sound model the standardized residuals stay within about 2 to 3 Standard Deviations. A Normal Distribution of the residuals is not produced by the mathematics of the fit: it is a separate assumption that has to be tested, which makes it the exception here.

Why the other options are wrong:

  • B. With an intercept in the model, the least squares residuals always sum to zero.
  • C. Standardized residuals beyond 3 Standard Deviations are treated as outliers that put the validity of the model in doubt.
  • D. Most standardized residuals falling within 2 Standard Deviations is what a sound model shows.

Question 36

When a Belt conducts a Linear Correlation Analysis and finds that as an X increases the Y also increase then he has proven a ______________ correlation.

  • A. Negative
  • B. Positive
  • C. Monomial
  • D. Single alignment
Show answer and explanation ▾

Correct answer: B

A Positive correlation means the two variables move in the same direction: as X increases, Y increases too.

Why the other options are wrong:

  • A. A Negative correlation means Y decreases as X increases.
  • C. Monomial is not a type of correlation.
  • D. Single alignment is not a type of correlation.

Question 37

A valid Multiple Linear Regression (MLR) is characterized by all of these except _______________________.

  • A. It is an assumption that the X’s (inputs) are not correlated to each other
  • B. The X’s (inputs) are assumed to be independent of each other
  • C. MLR is conducted based on a deliberate form of experimentation
  • D. The Residuals from MLR analysis have to be Normally Distributed
Show answer and explanation ▾

Correct answer: C

Multiple Linear Regression is normally run on passive or historical process data. Deliberate, planned changes to the inputs are the mark of a Designed Experiment, not of MLR.

Why the other options are wrong:

  • A. A valid MLR assumes the inputs are not correlated with each other.
  • B. A valid MLR assumes the inputs are independent of each other.
  • D. Normally Distributed Residuals are an assumption that is checked when an MLR is validated.

Question 38

It would be more likely than not for a Belt conducting a Regression Analysis to find that the _______________________.

  • A. r2 value is smaller than the absolute value of r
  • B. Correlation Coefficient equals r2
  • C. Coefficient of Determination is less than r2
  • D. Correlation Coefficient equals r divided by 2
Show answer and explanation ▾

Correct answer: A

The Correlation Coefficient r lies between -1 and 1. Squaring a number whose absolute value is below 1 makes it smaller, so r2 is almost always smaller than the absolute value of r.

Why the other options are wrong:

  • B. r2 is the Coefficient of Determination, which differs from the Correlation Coefficient r.
  • C. The Coefficient of Determination is r2 itself, so it cannot be less than r2.
  • D. The Correlation Coefficient is r, not r divided by 2.

Question 39

When a Belt properly analyzes the results of an experiment he must examine the Residuals in expectation of finding all of the following except _________.

  • A. Some Residuals higher than others
  • B. Some Residuals lower than others
  • C. All Residuals within 2 Standard Deviations of the Mean
  • D. Residuals will represent a Linear Regression
Show answer and explanation ▾

Correct answer: D

Residuals should be random with no structure. If they follow a line or any other pattern, the model has missed something, so a Belt does not expect the Residuals to represent a Linear Regression.

Why the other options are wrong:

  • A. Random scatter means some Residuals will be higher than others.
  • B. Random scatter means some Residuals will be lower than others.
  • C. How far the Residuals spread around their Mean is part of what the Belt checks.

Question 40

Which of these might contribute to similar distributions having Unequal Variance?

  • A. Extreme tails
  • B. Outliers
  • C. Multiple Modes
  • D. All of the above
Show answer and explanation ▾

Correct answer: D

Extreme tails, outliers and multiple modes all stretch the spread of a data set, so any of them can make otherwise similar distributions show Unequal Variance.

Why the other options are wrong:

  • A. Extreme tails are only one of the listed contributors.
  • B. Outliers are only one of the listed contributors.
  • C. Multiple Modes are only one of the listed contributors.

Question 41

A Belt working in a supply chain environment has to make a decision to change suppliers of critical raw materials for a new product upgrade. The purchasing manager is depending on the Belt’s effort requiring that the average cost of an internal critical raw material component be less than or equal to $4,200 in order to stay within budget. Using a sample of 35 first article components, a Mean of the new product upgrade price of $4,060, and a Standard Deviation of $98 was estimated. The Alternative Hypothesis in the above example is?

  • A. The Standard Deviation is equal to $300.
  • B. The Mean is less than $4,320.
  • C. The Mean is equal to $4,060.
  • D. The Mean is less than $4,200.
  • E. The Mean is greater than $ 4,200.
Show answer and explanation ▾

Correct answer: E

The Null Hypothesis holds the requirement with the equals sign: the Mean cost is less than or equal to $4,200. The Alternative Hypothesis is its complement, that the Mean is greater than $4,200.

Why the other options are wrong:

  • A. The hypothesis is about the Mean cost, and $300 appears nowhere in the scenario.
  • B. $4,320 is not the budget limit in the scenario.
  • C. $4,060 is the sample Mean, not the value being tested.
  • D. A Mean below $4,200 falls on the side of the requirement, which sits in the Null Hypothesis.

Question 42

A Belt working in a supply chain environment has to make a decision to change suppliers of critical raw materials for a new product upgrade. The purchasing manager is depending on the Belt’s effort requiring that the average cost of an internal critical raw material component be less than or equal to $3,600 in order to stay within budget. Using a sample of 42 first article components, a Mean of the new product upgrade price of $3,200 and a Standard Deviation of $180 was estimated. Based on the data provided, the Z value for the data assuming a Normal Distribution is?

  • A. 1.11
  • B. 2.22
  • C. 4.30
  • D. 5.42
Show answer and explanation ▾

Correct answer: B

Z is the distance from the Mean to the limit in Standard Deviations: (3,600 - 3,200) / 180 = 400 / 180 = 2.22.

Why the other options are wrong:

  • A. 1.11 is half of the correct value.
  • C. 4.30 does not result from dividing 400 by 180.
  • D. 5.42 does not result from dividing 400 by 180.

Question 43

A Belt working in a supply chain environment has to make a decision to change suppliers of critical raw materials for a new product upgrade. The purchasing manager is depending on the Belt’s effort requiring that the average cost of an internal critical raw material component be less than or equal to $3,800 in order to stay within budget. Using a sample of 38 first article components, a Mean of the new product upgrade price of

$3,680, and a Standard Deviation of $120 was estimated. In order to increase the Long Term Z value to 5, what is the maximum long term variation in pricing the Belt can accept for his upgraded critical raw material component?

  • A. $6
  • B. $12
  • C. $24
  • D. $48
Show answer and explanation ▾

Correct answer: C

The distance from the Mean to the limit is 3,800 - 3,680 = $120. For a Z value of 5, that distance must equal 5 Standard Deviations, so the maximum Standard Deviation is 120 / 5 = $24.

Why the other options are wrong:

  • A. $6 would give a Z value of 20, far tighter than required.
  • B. $12 would give a Z value of 10, tighter than required.
  • D. $48 would give a Z value of only 2.5.

Question 44

Sally and Sara sell flower pots at their garage sale. Sally motivates Sara mentioning that they will sell a minimum of 15 pots per day if the outside temperature exceeds 60o F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 13.6 pots per day were sold with a Standard Deviation of 0.7 pots. For the sales accomplished above, what test would validate if they met their requirements?

  • A. F Test
  • B. Test for Equal Variance
  • C. Chi Square Test
  • D. One-Sample t-Test
Show answer and explanation ▾

Correct answer: D

One sample Mean (13.6 pots) is being compared with a target value (15 pots), and the Standard Deviation comes from the sample. That is the case for a One-Sample t-Test.

Why the other options are wrong:

  • A. An F Test compares the variances of two samples.
  • B. A Test for Equal Variance compares spread between groups, not a Mean against a target.
  • C. A Chi Square Test is used for counts and proportions, not for a Mean.

Question 45

Sally and Sara sell flower pots at their garage sale. Sally motivates Sara mentioning that they will sell a minimum of 15 pots per day if the outside temperature exceeds 60o F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 13.6 pots per day were sold with a Standard Deviation of 0.7 pots. The statistical Degrees of Freedom for this example are?

  • A. 1
  • B. 29
  • C. 30
  • D. 31
  • E. 2
Show answer and explanation ▾

Correct answer: B

For a One-Sample t-Test the Degrees of Freedom are the sample size minus 1. With 30 days of data that is 30 - 1 = 29.

Why the other options are wrong:

  • A. 1 is not the sample size minus 1.
  • C. 30 is the sample size, before subtracting 1.
  • D. 31 adds 1 to the sample size instead of subtracting it.
  • E. 2 is not the sample size minus 1.

Question 46

Sally and Sara sell flower pots at their garage sale. Martha motivates Rose mentioning that they will sell a minimum of 16 pots per day if the outside temperature exceeds 60o F. From a sample, whose population is assumed to follow a Normal Distribution, taken for 30 days at 60 degrees or more an average of 15.2 pots per day were sold with a Standard Deviation of 0.6 pots.

What is the Z value for this sales process?

  • A. 0.67
  • B. 1.13
  • C. 1.33
  • D. 2.66
Show answer and explanation ▾

Correct answer: C

Z is the distance between the requirement and the Mean in Standard Deviations: (16 - 15.2) / 0.6 = 0.8 / 0.6 = 1.33.

Why the other options are wrong:

  • A. 0.67 is half of the correct value.
  • B. 1.13 does not result from dividing 0.8 by 0.6.
  • D. 2.66 is double the correct value.

Question 47

The relationship between a response variable and one or more independent variables is investigated and modeled by use of __________________.

  • A. X-Y Matrix
  • B. Baldridge Assessment
  • C. Analysis of Variance (ANOVA)
  • D. Critical X's Definition
Show answer and explanation ▾

Correct answer: C

Analysis of Variance tests whether one or more independent variables have a statistically significant effect on a response variable, which makes it the listed tool for investigating and modeling that relationship.

Why the other options are wrong:

  • A. An X-Y Matrix ranks inputs by team judgment and does not model a relationship statistically.
  • B. Baldridge Assessment is a business excellence review, not a statistical method.
  • D. Critical X's Definition is not a statistical modeling method.

Question 48

An ANOVA used across many dependent variables could increase the Beta risk.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: B

Running a test many times raises the chance of a false positive, which is the Alpha risk. It is the Alpha risk that grows with repeated testing, not the Beta risk.

Why the other options are wrong:

  • A. Repeated testing inflates the Alpha risk, not the Beta risk.

Question 49

The Mann-Whitney test is a powerful test and is unique to situations from which of the choices listed? (Note: There are 2 correct answers). (Choose two.)

  • A. Testing the identity of two populations
  • B. Focuses on equality of the Median of the two populations
  • C. Less powerful than the traditional “t-test”
  • D. More widely applicable than the traditional “t-test”
Show answer and explanation ▾

Correct answer: B, D

The Mann-Whitney test compares the Medians of two populations using ranks. It does not require Normal data, so it can be applied in more situations than the traditional t-test.

Why the other options are wrong:

  • A. The test is framed here around the Medians of the two populations.
  • C. Being less powerful would not describe a test the question calls powerful.

Question 50

Assessing process proportion as opposed to evaluating a process with respect to a set target can be done using which of these?

  • A. Process proportion equals some value range
  • B. Process proportion equals some desired value
  • C. Target is current
  • D. Proportion of the tail is equal
Show answer and explanation ▾

Correct answer: B

A proportion test checks whether the process proportion equals some desired value. That hypothesized value plays the same role for a proportion that a target plays for a Mean.

Why the other options are wrong:

  • A. A proportion test compares against a single stated value, not a range.
  • C. Whether the target is current is not how a process proportion is assessed.
  • D. Tail proportions being equal is not the hypothesis of a proportion test.

Question 51

A Non-parametric Test should be used if just one distribution is not Normal out of the two or more gathered.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

Parametric tests assume every sample comes from a Normal Distribution. If even one of the distributions is not Normal, that assumption fails and a Non-parametric Test should be used.

Why the other options are wrong:

  • B. One Non-normal distribution is enough to break the assumption behind the parametric tests.

Question 52

Contingency Tables are used to test for association, or dependency, between two or more classifications.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

A Contingency Table cross-tabulates counts by two or more classifications, and a Chi Square test on it shows whether the classifications are associated or independent.

Why the other options are wrong:

  • B. Testing for association between classifications is the purpose of a Contingency Table.

Question 53

A(n) ______________ is best used to compare a Machine 1 average quality characteristic to the same quality characteristic of Machine 2.

  • A. F test
  • B. 1-Sample t-test
  • C. 2-Sample t-test
  • D. ANOVA test
Show answer and explanation ▾

Correct answer: C

A 2-Sample t-test compares the Means of two independent samples, which is exactly the case of one quality characteristic measured on Machine 1 and on Machine 2.

Why the other options are wrong:

  • A. An F test compares two variances, not two averages.
  • B. A 1-Sample t-test compares one sample Mean with a fixed target value.
  • D. ANOVA is used to compare the Means of more than two groups.

Question 54

A(n) ________________ has occurred when two inputs have a greater impact on a change in the output than either of the inputs has by itself.

  • A. Dependency
  • B. Bimodal reaction
  • C. Interaction
  • D. Amplified effect
Show answer and explanation ▾

Correct answer: C

An Interaction exists when the effect of one input on the output depends on the level of another input, so the two together change the output more than either one does alone.

Why the other options are wrong:

  • A. Dependency is not the Design of Experiments term for a combined effect of two inputs.
  • B. Bimodal describes a distribution with two peaks, not a combined effect of inputs.
  • D. Amplified effect is not a defined term in experimental design.

Question 55

When conducting a Hypothesis Test using Continuous Data the proper sample size is influenced by the extent to which we need to assess a Difference to be detected and the inherent variation in the process.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

Sample size for a test on Continuous Data depends on the size of the difference that must be detected and on the process variation. A smaller difference or a larger Standard Deviation calls for more samples.

Why the other options are wrong:

  • B. The difference to detect and the process variation are both direct inputs to the sample size calculation.

Question 56

The validity of the decision made with Hypothesis Testing is dependent upon all of these except __________________.

  • A. Beta risk
  • B. Alpha risk
  • C. Range of data
  • D. Sample size
Show answer and explanation ▾

Correct answer: C

The reliability of a Hypothesis Test decision rests on the Alpha risk, the Beta risk and the sample size, which together set the chance of a wrong conclusion. The Range of the data is not one of the quantities that sets those risks.

Why the other options are wrong:

  • A. Beta risk is the chance of missing a real difference, so it bears directly on the decision.
  • B. Alpha risk is the chance of declaring a difference that does not exist, so it bears directly on the decision.
  • D. Sample size controls how well the test can detect a difference.

Question 57

Statistical Difference is the magnitude of difference or change required to distinguish between a true difference, brought about by change or improvement, and one that could have occurred by chance.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

Statistical Difference is the amount of change needed to separate a true difference, caused by a change or improvement, from one that could appear by chance alone. This is the basis for judging significance in a Hypothesis Test.

Why the other options are wrong:

  • B. The statement matches the definition of Statistical Difference.

Question 58

To be an effective Lean Six Sigma practitioner one must understand the difference between ___________________________.

  • A. ANOVA and the Analysis of Variance
  • B. Nonparametric tests and tests of Non-normal Data
  • C. F-test and test of variances of 2 samples
  • D. Practical and Statistical significance
Show answer and explanation ▾

Correct answer: D

A result can be statistically significant yet too small to matter to the business, or large enough to matter yet not statistically proven. A practitioner must judge both Practical and Statistical significance before acting on a result.

Why the other options are wrong:

  • A. ANOVA and the Analysis of Variance are the same thing.
  • B. Nonparametric tests are the tests used for Non-normal Data, so there is no difference to learn.
  • C. The F-test is the test of the variances of 2 samples, so the two are the same.

Question 59

A Belt is analyzing data and upon creation of the graphical analysis sees multiple modes. One of the primary reasons this could occur is because the process has experienced a ____________________.

  • A. Significant change from one shift to another
  • B. Sizable Measurement System error
  • C. Catastrophic failure of some sort
  • D. Any one of these
Show answer and explanation ▾

Correct answer: D

Multiple modes mean the data come from more than one distribution. A shift-to-shift change, a large Measurement System error or a major failure can each move part of the data to a new center, so any one of them can produce more than one peak.

Why the other options are wrong:

  • A. A shift change is only one of the listed causes, and the others apply as well.
  • B. Measurement System error is only one of the listed causes, and the others apply as well.
  • C. A catastrophic failure is only one of the listed causes, and the others apply as well.

Question 60

Time is always the metric on the horizontal scale of a(n) ___________ Chart.

  • A. Pareto
  • B. Xbar
  • C. Multi-Vari
  • D. NP
Show answer and explanation ▾

Correct answer: C

A Multi-Vari Chart displays within-unit, between-unit and temporal variation together, so it is laid out along a time scale on the horizontal axis to show how the output changes over time.

Why the other options are wrong:

  • A. A Pareto Chart has categories of defects or causes on the horizontal scale.
  • B. An Xbar chart has the subgroup number on the horizontal scale.
  • D. An NP chart has the sample or subgroup number on the horizontal scale.

Question 61

To properly analyze the variables impacting the output of a process we need to collect data that represents at least 80% of the variation in the process and assure ourselves we are collecting data from all three types of variation which are _______________.

  • A. Within, Between and Temporal
  • B. Within, Between and Temporary
  • C. Without, Above and Below
  • D. Induced, Natural and Unavoidable
Show answer and explanation ▾

Correct answer: A

Process variation is grouped into three families: Within unit (positional), Between units (cyclical) and Temporal (over time). Data collection must cover all three to capture most of the variation in the process.

Why the other options are wrong:

  • B. The third family is Temporal, meaning over time, not Temporary.
  • C. Without, Above and Below are not families of variation.
  • D. Induced, Natural and Unavoidable are not the three families used in Multi-Vari studies.

Question 62

When the Inputs, X’s, for your process are Normally Distributed about the Mean, the Outputs, Y’s, will always be Normally Distributed.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: B

Normally Distributed inputs do not guarantee a Normally Distributed output. The output depends on how the inputs combine, and nonlinear relationships or interactions can produce a skewed output.

Why the other options are wrong:

  • A. The word always makes the statement false, because the transfer function can change the shape of the output.

Question 63

On a _________________ Belt screens variables, or various inputs, to analyze their relative impact on the output of concern.

  • A. X-Y Matrix
  • B. Weighted Scale
  • C. Multi-Vari Chart
  • D. Poisson Chart
Show answer and explanation ▾

Correct answer: C

A Multi-Vari Chart plots the output against several inputs at once, so a Belt can screen the inputs and see which families of variation have the largest impact on the output of concern.

Why the other options are wrong:

  • A. An X-Y Matrix ranks inputs by team scoring and does not analyze process data.
  • B. A Weighted Scale is not a tool for screening process inputs.
  • D. Poisson Chart is not the tool used to screen inputs against an output.

Question 64

For a Normal Distribution as samples size increases the Range in Mean and Standard Deviation decrease relative to the Mean and Standard Deviation of the population.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

Larger samples give estimates that sit closer to the true population values. As sample size grows, the sample Mean and sample Standard Deviation vary over a narrower range around the population Mean and Standard Deviation.

Why the other options are wrong:

  • B. Larger samples reduce the spread of the sample estimates around the population values.

Question 65

Some of the sources for different types of error that can be quantified using Statistical Analysis are __________________.

  • A. Error in sampling
  • B. Bias in sampling
  • C. Error in measurement
  • D. All of these answers are correct
Show answer and explanation ▾

Correct answer: D

Sampling error, sampling bias and measurement error can each be estimated with statistical methods, for example through confidence intervals and Measurement System Analysis, so all three belong in the list.

Why the other options are wrong:

  • A. Error in sampling is only one of the three sources that can be quantified.
  • B. Bias in sampling is only one of the three sources that can be quantified.
  • C. Error in measurement is only one of the three sources that can be quantified.

Question 66

Since Normality is required if we intend to use the data collected as a predictive tool. To test for Normality of data we must determine if the Pvalue is ___________.

  • A. Equal to 0.05
  • B. Less than 0.05
  • C. Greater than 0.05
  • D. Greater than 0.5
Show answer and explanation ▾

Correct answer: C

In a normality test the Null Hypothesis is that the data follow a Normal Distribution. A P-value greater than 0.05 means the Null Hypothesis is not rejected, so the data can be treated as Normal.

Why the other options are wrong:

  • A. A P-value exactly equal to 0.05 is the boundary, not the condition for accepting normality.
  • B. A P-value less than 0.05 rejects normality.
  • D. The threshold is 0.05, not 0.5.

Question 67

The Normal Distribution is considered to be the most important distribution in statistics and, among other things is defined as having a total area under the curve of 1, is mounded and symmetrical and the Mean, Median and Mode are _____________.

  • A. All evenly divisible by 3
  • B. Twice the Standard Deviation
  • C. Within 10% of each other
  • D. The same number
Show answer and explanation ▾

Correct answer: D

A Normal Distribution is symmetrical about its center, so the Mean, the Median and the Mode all fall at the same point.

Why the other options are wrong:

  • A. Divisibility by 3 has nothing to do with the Normal Distribution.
  • B. The center of the distribution is not tied to twice the Standard Deviation.
  • C. The three measures are equal, not merely close to each other.

Question 68

Following process modifications, the Null Hypothesis states that no improvement to the process has occurred. If we discover the Null Hypothesis Test was rejected when it was false, that would be a(n) ________________________.

  • A. Alpha Error
  • B. Type I Error
  • C. Type II Error
  • D. Type III Error
Show answer and explanation ▾

Correct answer: C

A Type II Error is the error tied to a Null Hypothesis that is false: the test fails to detect a real change in the process, and its probability is the Beta risk. Alpha and Type I Errors can only occur when the Null Hypothesis is true.

Why the other options are wrong:

  • A. An Alpha Error is the rejection of a Null Hypothesis that is true, not one that is false.
  • B. A Type I Error is the rejection of a Null Hypothesis that is true, not one that is false.
  • D. Type III Error is not one of the two standard errors of Hypothesis Testing.

Question 69

A statistical test or Hypothesis Test is performed to reject or fail to reject a stated hypothesis and it converts the Practical Problem into a Statistical Problem.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

A Hypothesis Test restates the Practical Problem as a Statistical Problem with a Null and an Alternative Hypothesis. The test then leads to one of two decisions: reject the Null Hypothesis or fail to reject it.

Why the other options are wrong:

  • B. Converting the Practical Problem into a Statistical Problem is exactly what a Hypothesis Test does.

Question 70

How many experimental runs exist in a Full Factorial and fully randomized design for 5 factors with 2 replicates for the Corner Points and no Center Points? The factors in the experiment are only at 2-levels.

  • A. 10
  • B. 128
  • C. 256
  • D. 64
Show answer and explanation ▾

Correct answer: D

A 2-level Full Factorial with 5 factors has 2 to the power of 5, or 32, corner point combinations. Two replicates run each combination twice, giving 32 x 2 = 64 experimental runs.

Why the other options are wrong:

  • A. 10 is 5 factors times 2 levels, which is not how factorial runs are counted.
  • B. 128 would need four replicates of the 32 combinations.
  • C. 256 does not result from 32 combinations run twice.

Question 71

If an experiment has 5 factors and no replicates for a 2-level Experimental Design with 16 experimental runs which statement(s) are correct? (Note: There are 3 correct answers). (Choose three.)

  • A. The Main Effects for the 5 factors are not aliased or confounded but the 2-way interactions are confounded with the 3-way interactions
  • B. The Main Effects are confounded with only 4-way interactions
  • C. The Experimental Design is half-fractional
  • D. The experiment has 8 experimental runs with the first factor at the high level
  • E. The experiment has only 4 experimental runs with the 5th factor at the high level
Show answer and explanation ▾

Correct answer: B, C, D

A 2-level Full Factorial for 5 factors needs 32 runs, so 16 runs is a half fraction. In this Resolution V design each Main Effect is confounded with a 4-way interaction, and every factor sits at its high level in half of the runs, which is 8.

Why the other options are wrong:

  • A. The Main Effects are aliased with 4-way interactions, so the claim that they are not aliased or confounded fails.
  • E. The 5th factor is at the high level in 8 of the 16 runs, not 4.

Question 72

With Measurement System Analysis we are concerned with two issues that impact the potential variability of the data. They are ____________ and Accuracy.

  • A. Spread
  • B. Reliability
  • C. Precision
  • D. Deflection
Show answer and explanation ▾

Correct answer: C

Measurement System Analysis looks at Accuracy, how close measurements are to the true value, and Precision, how close repeated measurements are to each other. Precision covers Repeatability and Reproducibility.

Why the other options are wrong:

  • A. Spread is not the term paired with Accuracy in Measurement System Analysis.
  • B. Reliability is not the term paired with Accuracy in Measurement System Analysis.
  • D. Deflection is not a Measurement System Analysis term.

Question 73

An operator is measuring the distance between two points.

Which is most likely to be influenced by the operator?

  • A. Precision of the measurement
  • B. Accuracy of the measurement
  • C. Calibration of the instrument
  • D. All of these answers are correct
Show answer and explanation ▾

Correct answer: D

The person taking a measurement affects how consistently the gage is used, how close the readings come to the true value, and how the instrument is set up and calibrated before use. All three are open to operator influence.

Why the other options are wrong:

  • A. Precision is only one of the three items the operator can influence.
  • B. Accuracy is only one of the three items the operator can influence.
  • C. Calibration is only one of the three items the operator can influence.

Question 74

Accuracy can be assessed in several ways and a fairly accurate means of measurement is visual comparison.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: B

Visual comparison is subjective and varies from person to person, so it is not a fairly accurate means of measurement. Accuracy is assessed by comparing measurements with a known reference standard.

Why the other options are wrong:

  • A. Visual comparison depends on individual judgment and is not an accurate means of measurement.

Question 75

Measurement __________ is defined as the difference between the observed and the expected values for a given set of data.

  • A. Breadth
  • B. Linearity
  • C. Range
  • D. Bias
Show answer and explanation ▾

Correct answer: D

Bias is the difference between the observed average of the measurements and the expected, or reference, value. It shows how far the Measurement System sits from the true value.

Why the other options are wrong:

  • A. Breadth is not a Measurement System Analysis term.
  • B. Linearity describes how Bias changes across the measuring range of the gage.
  • C. Range is the difference between the largest and smallest values in the data.

Question 76

Appropriate measures mean that measurements are ______________.

  • A. Representative
  • B. Sufficient
  • C. Contextual
  • D. Relevant
  • E. All of these answers are correct
Show answer and explanation ▾

Correct answer: E

Appropriate measures are Sufficient in number, Relevant to the problem, Representative of the process and Contextual, meaning collected with the related information needed to interpret them. All four properties apply.

Why the other options are wrong:

  • A. Representative is only one of the four properties of appropriate measures.
  • B. Sufficient is only one of the four properties of appropriate measures.
  • C. Contextual is only one of the four properties of appropriate measures.
  • D. Relevant is only one of the four properties of appropriate measures.

Question 77

A ___________ problem in the Measurement System suggests that there is a lack of consistency in the measurement over time.

  • A. Linearity
  • B. Bias
  • C. Stability
  • D. Magnitude
Show answer and explanation ▾

Correct answer: C

Stability is the ability of a Measurement System to give the same results on the same items over time. A Stability problem means the measurements drift or change from one period to the next.

Why the other options are wrong:

  • A. Linearity concerns how Bias changes across the measuring range, not over time.
  • B. Bias is the offset between the observed average and the reference value.
  • D. Magnitude is not a Measurement System Analysis term.

Question 78

An operator checks that all boxes being packed contain enough products to fill the box. However, each box getting filled has a different number of products in it. This is a Reproducibility problem, not a Repeatability problem.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: B

Reproducibility is the variation between different operators measuring the same items. Only one operator is involved here, so the inconsistency cannot be a Reproducibility problem.

Why the other options are wrong:

  • A. Reproducibility requires a comparison between operators, and the scenario has a single operator.

Question 79

In a good Measurement System the most variation will be with part-to-part measurements.

What should you do if the majority of variation is associated with the Gage R&R assuming the gage is technically capable?

  • A. Focus on fixing the Repeatability and Reproducibility of the measurement device
  • B. Purchase a new machine
  • C. Focus on trimming the Part-to-Part variation
  • D. Run another MSA test with the machine
Show answer and explanation ▾

Correct answer: A

When most of the observed variation comes from the Gage R&R, the Measurement System itself is the problem. Since the gage is technically capable, the work is to fix Repeatability and Reproducibility, for example through operator training, fixtures and a standard measuring method.

Why the other options are wrong:

  • B. The gage is stated to be technically capable, so buying a new machine is not the remedy.
  • C. Part-to-Part variation is the variation a good Measurement System is supposed to show, not the problem.
  • D. Repeating the study does not correct the cause of the measurement variation.

Question 80

Each of the items listed would impact the Process Capability for a process with a continuous output except ___________________.

  • A. Shape of process data distribution (e.g. Normal Distribution)
  • B. Process Technology
  • C. Process Standard Deviation
  • D. Seasonal variation in process
Show answer and explanation ▾

Correct answer: B

Process Capability for a continuous output is calculated from the data: the shape of the distribution, the Standard Deviation and how the process varies over time, including seasonal variation. Process Technology is not an input to that calculation.

Why the other options are wrong:

  • A. The shape of the distribution decides which capability method and calculations are valid.
  • C. The Standard Deviation is a direct input to every capability index.
  • D. Seasonal variation adds to long-term variation and lowers capability.

Question 81

For Attribute Data, Process Capability is defined as the average proportion of nonconforming products.

  • A. True
  • B. False
Show answer and explanation ▾

Correct answer: A

Attribute Data only records whether a unit conforms, so there is no Mean and Standard Deviation to compare with specification limits. Capability is expressed as the average proportion of nonconforming product.

Why the other options are wrong:

  • B. The average proportion nonconforming is the accepted definition of capability for Attribute Data.

Question 82

The reported Cpk for a process with an average of 104 units, a spread of 18 units and upper and lower specification limits of 122 and 96 units would be?

  • A. 0.5
  • B. 0.89
  • C. 1.00
  • D. 2.00
Show answer and explanation ▾

Correct answer: B

A spread of 18 units is 6 Standard Deviations, so 3 Standard Deviations is 9. The upper side gives (122 - 104) / 9 = 2.00 and the lower side gives (104 - 96) / 9 = 0.89. Cpk is the smaller of the two, 0.89.

Why the other options are wrong:

  • A. 0.5 does not result from either side of the Cpk calculation.
  • C. 1.00 does not result from either side of the Cpk calculation.
  • D. 2.00 is the upper side value, and Cpk takes the smaller of the two sides.

Question 83

When we compare short-term and long-term Capability which of these is true?

  • A. Cp is better for the short term
  • B. Both short-term and long-term performance are alike
  • C. Performance tends to improve over time
  • D. Cp is better for the long-term
Show answer and explanation ▾

Correct answer: A

Short-term data contain only the common cause variation within subgroups, while long-term data also include shifts and drifts of the process. The Standard Deviation is therefore smaller in the short term, which gives a better Cp.

Why the other options are wrong:

  • B. Long-term data include shifts and drifts that short-term data do not, so the two are not alike.
  • C. Long-term performance is typically worse than short-term performance, because more sources of variation appear over time.
  • D. Long-term variation is larger, so capability is lower in the long term.

Question 84

Relative to a Design of Experiments the term Collinear refers to variables being a ________________ of each other.

  • A. Linear combination
  • B. Directly parallel
  • C. Mirror image
  • D. None of the above
Show answer and explanation ▾

Correct answer: A

Variables are Collinear when one can be written as a linear combination of the others. Their effects then cannot be separated in the analysis, which is why designed experiments keep the factors independent.

Why the other options are wrong:

  • B. Directly parallel is not the definition of Collinear in experimental design.
  • C. A mirrored copy is not the definition of Collinear in experimental design.
  • D. Linear combination is the correct definition, so None of the above does not apply.

Question 85

Which Experimental Design typically is most associated with the fewest number of input variables or factors in the design?

  • A. Response Surface design
  • B. Full Factorial design
  • C. Simple Linear Regression
  • D. Fractional Factorial design
Show answer and explanation ▾

Correct answer: A

A Response Surface design is used late in experimentation, after screening has reduced the inputs to the vital few. It models curvature for a small number of factors to find optimum settings.

Why the other options are wrong:

  • B. A Full Factorial design is commonly run with more factors than a Response Surface design.
  • C. Simple Linear Regression is an analysis method, not an Experimental Design.
  • D. A Fractional Factorial design is chosen when there are many factors to screen.

Question 86

The Lean toolbox includes all of the following items except __________.

  • A. Poke-Yoke
  • B. Standard Operating Procedures
  • C. Kaizen
  • D. 5S the work area
Show answer and explanation ▾

Correct answer: B

Poke-Yoke, Kaizen and 5S are named Lean tools for preventing mistakes, running improvement events and organizing the workplace. Standard Operating Procedures are general process documentation and are not counted among the Lean tools here.

Why the other options are wrong:

  • A. Poke-Yoke, or mistake proofing, is a Lean tool.
  • C. Kaizen is a Lean tool for rapid improvement.
  • D. 5S is a Lean tool for organizing the work area.

Question 87

Questions that can be best answered by a Visual Factory include all of these except _____________________.

  • A. Are setups optimized for lower scrap levels?
  • B. Can extra inventory be seen easily?
  • C. Can changeover challenges be recognized?
  • D. Are unneeded tools or supplies easily noted?
Show answer and explanation ▾

Correct answer: A

A Visual Factory makes the status of the workplace obvious at a glance, such as extra inventory, unneeded tools and changeover problems. Whether setups are optimized for lower scrap needs data and analysis, not a visual check.

Why the other options are wrong:

  • B. Extra inventory is something a Visual Factory makes easy to see.
  • C. Changeover problems are made visible by a Visual Factory.
  • D. Unneeded tools or supplies are easy to spot in a Visual Factory.

Question 88

Situations where standardizedwork needs to be incorporated include all of these except _____________________.

  • A. Changeover instructions incomplete
  • B. Lack of a system to assure proper inventory levels at repair stations
  • C. Machines continually operating to reduce the labor cost per piece
  • D. Process flow for the same product assembly taking various cycle time for completion
Show answer and explanation ▾

Correct answer: C

Standardized work documents the best current method so that tasks are done the same way every time. Running machines continually to lower labor cost per piece is a production scheduling choice, not a gap that standardized work fills.

Why the other options are wrong:

  • A. Incomplete changeover instructions are a direct case for standardized work.
  • B. A missing system for inventory levels is a case for a standard method.
  • D. Varying cycle times for the same assembly show the work is not being done one standard way.

Question 89

If a Six Sigma project was to reduce changeover times and the team found the project success was decreasing over time since changeover times began to creep back up, which Lean tools should be considered in the Control Phase to reestablish and sustain the project success?

  • A. Improve the lighting to assure adequate visibility
  • B. Confirm a Visual Factory exists to assure proper communication of status of machines
  • C. Implement Kanbans to assure enough inventory for the process step
  • D. Reword the standardized work instructions to use active verbs and not passive phrases
Show answer and explanation ▾

Correct answer: B

Changeover times creep back up when the status of machines and the standard are no longer visible to the people doing the work. Confirming that a Visual Factory is in place restores clear communication of machine status and sustains the gain.

Why the other options are wrong:

  • A. Better lighting does not communicate machine status or changeover performance.
  • C. Kanbans manage inventory flow and do not address changeover times.
  • D. Rewording the instructions does not make the status of the machines visible.

That was 89 of 300.

The full GAQM CLSSBB pack has all 300 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.

Get the full pack

Not ready yet? Get the first 108 free as one PDF by email. Get the Half Pack →

About the CLSSBB exam

These 89 GAQM CLSSBB questions are free here. The free PDF has 108, free by email.

They are drawn from the same bank as the full CLSSBB pack, which has 300 questions in total.

Back to blog