CWNP CWISA-103 Practice Questions with Explanations
Free CWNP CWISA-103 practice questions. 23 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.
CWISA-103 practice questions
Question 1
What function does the IEEE perform in relation to wireless technologies?
- A. Promotes technology and standards development
- B. Brings wireless products to market
- C. Designs wireless chipsets
- D. Certified equipment to be compatible
Show answer and explanation ▾
Correct answer: A
The IEEE is a standards body. In wireless it develops the 802 standards, such as 802.11 and 802.15, and so promotes technology and standards development.
Why the other options are wrong:
- B. Bringing products to market is done by manufacturers, not by a standards body.
- C. Chipsets are designed by silicon vendors, not by the IEEE.
- D. Interoperability certification is done by industry alliances such as the Wi-Fi Alliance, not by the IEEE.
Question 2
What is the most common difference between a single board computer (SBC) and a controller board?
- A. Controller boards have I/O headers and SBCs do not
- B. SBCs always have connectors for M2 devices and controller boards do not
- C. Controller boards have more powerful processors than most SBCs
- D. SBCs typically have connectors for display and input devices while controller boards do not
Show answer and explanation ▾
Correct answer: D
A single board computer is a complete small computer, so it normally has connectors for a display and input devices. A controller board is built to control hardware and usually lacks them.
Why the other options are wrong:
- A. SBCs often have I/O headers too, so this does not separate the two.
- B. M.2 connectors are not found on every SBC and are not what defines the difference.
- C. Controller boards usually use simpler processors than a typical SBC.
Question 3
What software is typically stored in ROM and is used to initialize a device?
- A. Firmware
- B. Container
- C. Application
- D. Service
Show answer and explanation ▾
Correct answer: A
Firmware is the low-level software kept in non-volatile memory such as ROM or flash. It runs when a device powers on and initializes the hardware.
Why the other options are wrong:
- B. A container packages an application and its dependencies and runs on top of an operating system.
- C. An application is user-level software, not the code that starts the hardware.
- D. A service is a background process provided by software that is already running.
Question 4
You have been asked to consider smart building opportunities for your organization.
Which one of these is a benefit of smart building technology?
- A. Reduced design and construction costs
- B. Faster Wi-Fi connectivity
- C. Improved operational efficiency
- D. Increased vacation time for building managers
Show answer and explanation ▾
Correct answer: C
Smart building technology connects systems such as lighting, HVAC and access control so they can be monitored and tuned. The main benefit is better operational efficiency.
Why the other options are wrong:
- A. Smart building systems add equipment and integration work, so they do not reduce design and construction cost.
- B. Wi-Fi speed is a feature of the wireless network, not a benefit that comes from smart building technology.
- D. More vacation time for staff is not a benefit of the technology.
Question 5
How is ASK modulation different from FSK modulation?
- A. ASK varies the amplitude of the signal while FSK shifts its frequency
- B. ASK can carry more data than FSK
- C. ASK does not work at high frequencies
- D. FSK is more sensitive to noise than ASK
Show answer and explanation ▾
Correct answer: A
ASK (amplitude shift keying) changes the amplitude of the carrier to represent data, while FSK (frequency shift keying) changes its frequency.
Why the other options are wrong:
- B. The amount of data carried depends on the symbol rate and encoding, not on ASK compared with FSK in general.
- C. ASK can be used at high frequencies. It is simply more affected by amplitude noise.
- D. ASK is generally the more noise-sensitive of the two, because noise corrupts amplitude more easily than frequency.
Question 6
What does the number in the various Quadrature Amplitude Modulation levels, such as 16 in QAM-16 and 64 in QAM-64, indicate? (Choose the single best answer.)
- A. The number of target points in the QAM constellation, which are equivalent to amplitude and phase combinations
- B. The speed of data transfer, which is four times the number in the QAM level
- C. The channel width, which is stipulated in MHz
- D. The number of spatial streams, which is 1/4 the number in the QAM level
Show answer and explanation ▾
Correct answer: A
The number is the count of points in the constellation. Each point is a unique combination of amplitude and phase that represents a bit pattern, so 16-QAM has 16 points carrying 4 bits per symbol and 64-QAM has 64 points carrying 6 bits per symbol.
Why the other options are wrong:
- B. The number does not state a data rate; the rate also depends on channel width, coding and other factors.
- C. Channel width is a separate setting and is not given by the QAM number.
- D. Spatial streams are a MIMO property and have no fixed relation to the QAM number.
Question 7
What primary component is required to implement a wireless transceiver in a device?
- A. Flash memory
- B. Radio
- C. SRAM
- D. GPIO pins
Show answer and explanation ▾
Correct answer: B
A transceiver is a transmitter and a receiver combined, and that function is provided by the radio. Without a radio the device cannot send or receive RF signals.
Why the other options are wrong:
- A. Flash memory stores firmware and data and does not send or receive RF.
- C. SRAM is working memory and does not send or receive RF.
- D. GPIO pins connect sensors and other components and do not send or receive RF.
Question 8
How does OFDMA differ from OFDM?
- A. OFDMA offers greater range by using multiple channels at once
- B. OFDMA allows multiple devices to transmit simultaneously on the same frequency
- C. Subcarriers of OFDMA can contain data destined for a different receiver
- D. OFDMA uses multiple radios to achieve higher throughput
Show answer and explanation ▾
Correct answer: C
OFDM gives all subcarriers of a transmission to one receiver. OFDMA divides the subcarriers into groups called resource units, so different subcarriers in the same transmission can carry data for different receivers.
Why the other options are wrong:
- A. OFDMA does not extend range by combining multiple channels.
- B. OFDMA assigns each device its own subcarriers within the channel; the devices do not share the same frequency at the same time.
- D. OFDMA works with a single radio and does not depend on multiple radios.
Question 9
What metric is used to express a relative increase or decrease in signal strength?
- A. dBm
- B. mW
- C. W
- D. dB
Show answer and explanation ▾
Correct answer: D
The decibel (dB) is a relative unit that expresses the ratio between two power levels, so it is used for gain and loss. A change of +3 dB doubles the power and -3 dB halves it.
Why the other options are wrong:
- A. dBm is an absolute power level referenced to 1 milliwatt.
- B. The milliwatt is an absolute unit of power.
- C. The watt is an absolute unit of power.
Question 10
What kind of PoE device can be used to power a non-PoE connected object assuming PoE power is provided on the Ethernet cable?
- A. PoE endspan switch
- B. PoE midspan injector
- C. PoE splitter
- D. PoE coupler
Show answer and explanation ▾
Correct answer: C
A PoE splitter sits at the device end of the cable. It separates the power from the data and delivers them on two outputs, so a device without PoE support receives DC power on its power input and data on its Ethernet port.
Why the other options are wrong:
- A. An endspan switch is a source of PoE power, not a way to feed it to a non-PoE device.
- B. A midspan injector adds power to the cable; it does not separate it out for a non-PoE device.
- D. A coupler only joins two Ethernet cables together.
Question 11
As an RF signal propagates it becomes weaker at any given measurement point as it gets farther away from the transmitter.
What concept is described?
- A. RF latency
- B. Free Space Path Loss
- C. Diffraction
- D. Beamwidth
Show answer and explanation ▾
Correct answer: B
Free Space Path Loss is the drop in signal strength caused by the natural spreading of the wave front as it travels away from the transmitter. The same energy covers a larger area, so less of it reaches a receiver that is farther away.
Why the other options are wrong:
- A. Latency is a delay in time, not a loss of signal strength.
- C. Diffraction is the bending of a signal around an obstacle.
- D. Beamwidth describes how wide an antenna's main lobe is.
Question 12
What is a common characteristic of Industrial IoT (IIoT) devices that is not a characteristic of all IoT devices?
- A. Use of proprietary protocols
- B. Use of standardized protocols
- C. Transmission of small amounts of data throughout the day
- D. Ruggedized devices constructed for operating in harsh environments
Show answer and explanation ▾
Correct answer: D
Industrial IoT devices are commonly ruggedized to survive heat, cold, dust, moisture, vibration and electrical noise on factory floors and outdoor sites. Many consumer and office IoT devices are not built for those conditions.
Why the other options are wrong:
- A. Proprietary protocols appear in many kinds of IoT devices and are not specific to industrial ones.
- B. Standardized protocols appear in many kinds of IoT devices and are not specific to industrial ones.
- C. Sending small amounts of data through the day is typical of IoT devices in general.
Question 13
A Wi-Fi enabled weight scale is an example of what kind of health IoT device?
- A. non-wearable
- B. wearable
- C. implantable
- D. injectable
Show answer and explanation ▾
Correct answer: A
A connected weight scale is used at a fixed spot and is not carried on or placed in the body, so it is classed as a non-wearable health IoT device.
Why the other options are wrong:
- B. A wearable is worn on the body, such as a fitness band or a smartwatch.
- C. An implantable is placed inside the body, such as a pacemaker.
- D. An injectable is introduced into the body by injection.
Question 14
You are deploying a ZigBee network based on the frequency band available for ZigBee deployment worldwide.
What allowable action will do the most to minimize ZigBee and 802.11 interference?
- A. Use the 5 GHz band for all 802.11 communications
- B. Use the 2.4 GHz band for all 802.11 communications
- C. Use the 5 GHz band for all ZigBee communications
- D. Use the 6 GHz band for all ZigBee communications
Show answer and explanation ▾
Correct answer: A
The ZigBee band that is available worldwide is 2.4 GHz, which 802.11 also uses. Moving all 802.11 communications to 5 GHz removes the overlap between the two technologies, which reduces interference the most.
Why the other options are wrong:
- B. Putting all 802.11 traffic in 2.4 GHz places it in the same band as ZigBee and increases interference.
- C. ZigBee does not operate in the 5 GHz band.
- D. ZigBee does not operate in the 6 GHz band.
Question 15
You are planning a wireless solution deployment. The organization has several wireless solutions in use. The new deployment must coexist with these other wireless solutions.
What is the most important factor to consider when implementing the new wireless solution?
- A. Implementing matching encryption keys synchronized with the other wireless solutions
- B. Coordinating frequency use with the other wireless solutions
- C. Coordinating mounting locations with the other wireless solutions
- D. Implementing contrasting encryption keys countering the other wireless solutions
Show answer and explanation ▾
Correct answer: B
Wireless systems that share the same frequencies interfere with each other. Coordinating which bands and channels each solution uses lets the new deployment work alongside the existing ones without degrading them.
Why the other options are wrong:
- A. Matching encryption settings across unrelated systems does nothing for coexistence and weakens security.
- C. Mounting locations matter far less than the frequencies the systems use.
- D. Encryption settings have no effect on RF interference between systems.
Question 16
You are planning a wireless implementation. At what point should you begin to consider security requirements for the implementation?
- A. In the planning phase
- B. In the implementation phase
- C. In the acceptance testing phase
- D. During hand-off to support
Show answer and explanation ▾
Correct answer: A
Security requirements shape the choice of technology, devices, authentication and network design, so they must be gathered in the planning phase. Adding security later costs more and often leaves gaps.
Why the other options are wrong:
- B. By implementation the design and equipment are already chosen, which is too late to start on security requirements.
- C. Acceptance testing confirms that requirements were met; it is too late to define them.
- D. Hand-off to support happens after the solution is built, which is too late to define security requirements.
Question 17
You are defining capacity for a wireless solution.
What is the most important factor related to each use case defined in relation to capacity?
- A. Number of devices
- B. Protocols used on each device
- C. Total airtime utilization
- D. Support for mobility
Show answer and explanation ▾
Correct answer: C
The wireless medium is shared, so capacity is limited by airtime. The total airtime that a use case consumes, from all its devices and their traffic together, determines whether the channel can carry it.
Why the other options are wrong:
- A. A device count alone does not show the load, because devices differ widely in how much they transmit.
- B. The protocols in use matter only through the airtime they consume.
- D. Mobility support is a roaming requirement, not a measure of capacity.
Question 18
What is the spacing between ZigBee channels when operating in the 2.4 GHz frequency band?
- A. 1 MHz
- B. 2 MHz
- C. 5 MHz
- D. 25 MHz
Show answer and explanation ▾
Correct answer: C
In the 2.4 GHz band, IEEE 802.15.4, which ZigBee is built on, defines 16 channels, numbered 11 to 26. Each is 2 MHz wide and the channel centers are spaced 5 MHz apart.
Why the other options are wrong:
- A. 1 MHz is not the spacing between 2.4 GHz ZigBee channels.
- B. 2 MHz is the width of each channel, not the spacing between channel centers.
- D. 25 MHz is not the spacing between 2.4 GHz ZigBee channels.
Question 19
Which one of the following items has driven large-scale deployment of wireless devices in education verticals serving 5 to 18-year-old students?
- A. Cloud-based applications
- B. Wearable body sensors
- C. Online torrent sites
- D. Streaming music
Show answer and explanation ▾
Correct answer: A
Schools have moved teaching, coursework and testing to cloud-based applications that students reach from laptops and tablets. Giving every student reliable access to those applications has driven large-scale wireless deployments in primary and secondary education.
Why the other options are wrong:
- B. Wearable body sensors are not a driver of school wireless deployments.
- C. Torrent sites are normally blocked on school networks.
- D. Streaming music is not an educational requirement that drives deployments.
Question 20
You are planning a wireless solution.
Why should you consider an ongoing monitoring system for use after the solution is deployed?
- A. Implementation validation is never completed, it continues throughout the life of the system
- B. The number of users and the use of the solution will change over time and monitoring allows for detection of these changes
- C. Monitoring the solution provides additional billable hours
- D. To ensure that the system continues to meet the original requirements, even if users later indicate poor performance
Show answer and explanation ▾
Correct answer: B
A wireless solution is designed for the users, devices and applications known at deployment. Those change over time, and ongoing monitoring reveals the changes so the solution can be adjusted before performance suffers.
Why the other options are wrong:
- A. Implementation validation is completed at deployment; monitoring afterward is a separate operational activity.
- C. Billable hours are not a technical reason to monitor a solution.
- D. Meeting the original requirements is not the goal once users report poor performance and needs have changed.
Question 21
You are creating documentation for a new wireless solution that is deployed in the organization.
Why is it important to document APIs in use within the system?
- A. If APIs are in use, it typically indicates the use of custom scripts or application code. Future support will be easier when the APIs in use are documented.
- B. The APIs in use will not function without this documentation. The documentation is linked to the executable process of the APIs.
- C. It allows future support to implement APIs that have not been used at the time of deployment.
- D. If APIs are in use, it typically indicates that the vendor has not provided ideal support. Without documentation, you cannot prove this reality for a discount.
Show answer and explanation ▾
Correct answer: A
APIs are normally used by custom scripts or application code that integrate the wireless solution with other systems. Documenting which APIs are used, and how, lets future support staff understand, troubleshoot and update those integrations.
Why the other options are wrong:
- B. APIs run regardless of whether any documentation exists.
- C. The purpose is to record the APIs that are in use, not ones that were never used.
- D. API use is a normal part of integration and does not indicate poor vendor support.
Question 22
Key performance indicators and business requirements are most relevant to what operational activity for an existing wireless IoT solution?
- A. Upgrading
- B. Removal
- C. Implementation
- D. Monitoring
Show answer and explanation ▾
Correct answer: D
Monitoring an operating solution means measuring it against its performance indicators to confirm that it still meets the business requirements. Those measurements show when the solution needs attention.
Why the other options are wrong:
- A. Upgrading is a change made after monitoring shows a need for it.
- B. Removal retires a solution and is not driven by ongoing performance measurement.
- C. Implementation applies to a new solution, not to one that already exists.
Question 23
Why is it important to adhere to safety and building codes when installing equipment?
- A. It prevents equipment from falling to the floor and being damaged because of the impact
- B. They can be ignored as they are regulations designed for other industries
- C. It is an insurance requirement designed to reduce insurance rates and reduce incident reports against insurance policies
- D. It protects the life and health of installers and end users during installation and after the system is deployed
Show answer and explanation ▾
Correct answer: D
Safety and building codes exist to protect people. Following them guards installers during the work and protects the occupants afterward from hazards such as fire, electrical faults and falling equipment.
Why the other options are wrong:
- A. Protecting the equipment from damage is not the main purpose of the codes.
- B. The codes apply to wireless installations and cannot be ignored.
- C. Insurance cost is not the reason the codes exist.
That was 23 of 60.
The full CWNP CWISA-103 pack has all 60 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.
Get the full packNot ready yet? Get the first 23 free as one PDF by email. Get the Half Pack →
About the CWISA-103 exam
These 23 CWNP CWISA-103 questions are free here, and as a free PDF by email.
They are drawn from the same bank as the full CWISA-103 pack, which has 60 questions in total.