CWNP CWDP-305 Practice Questions with Explanations

Free CWNP CWDP-305 practice questions. 23 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.

CWDP-305 practice questions

Question 1

When designing a Wi-Fi based WLAN to support voice in a large office, which design element is of the highest concern for performance?

  • A. AP enclosures
  • B. Roaming
  • C. AP vendor
  • D. Support for 900 Mhz
Show answer and explanation ▾

Correct answer: B

Voice calls need a client to move between access points without a noticeable gap, so roaming performance is the design element that matters most in a large voice WLAN.

Why the other options are wrong:

  • A. Enclosures protect or hide access points but do not decide voice performance.
  • C. The brand of AP matters far less than how the design handles roaming and capacity.
  • D. 900 MHz is not a Wi-Fi band used in WLAN design for voice.

Question 2

What is the minimum PoE budget required to power 6 APs using IEEE 802.3at with no additional details provided?

  • A. 320 W
  • B. 60 W
  • C. 180 W
  • D. 240 W
Show answer and explanation ▾

Correct answer: D

With no details about the actual draw of the APs, each of the six ports has to be budgeted at the full IEEE 802.3at allocation with headroom, and 240 W is the budget that covers all six.

Why the other options are wrong:

  • A. 320 W is more than the minimum needed for six 802.3at ports.
  • B. 60 W cannot power six 802.3at APs.
  • C. 180 W leaves no headroom across six 802.3at ports.

Question 3

In high-density environments like stadiums or convention centers, what additional factor must be considered that can attenuate Wi-Fi signals during events

  • A. Thick walls
  • B. I-Beams
  • C. People
  • D. Fire doors
Show answer and explanation ▾

Correct answer: C

In stadiums and convention centres the crowd itself absorbs Wi-Fi signal, and the attenuation changes as the venue fills, so the design must account for people.

Why the other options are wrong:

  • A. Thick walls are fixed and already part of the normal survey and design.
  • B. I-beams are structure that is known in advance and does not change during an event.
  • D. Fire doors are a fixed obstacle and not the extra factor that appears with crowds.

Question 4

Which document outlines the objectives, scope, and key stakeholders, serving as the official authorization to begin a WLAN design and deployment project?

  • A. Bill of Materials
  • B. Project Charter
  • C. Work Breakdown Structure
  • D. Budget
Show answer and explanation ▾

Correct answer: B

The project charter states the objectives, scope and key stakeholders and formally authorizes the project to start.

Why the other options are wrong:

  • A. A bill of materials lists the equipment to be bought, not the project's authorization.
  • C. A work breakdown structure splits the work into tasks after the project is authorized.
  • D. A budget covers cost only and does not authorize the project or name stakeholders.

Question 5

When conducting information gathering for a WLAN design, which document ensures your customer’s proprietary information remains confidential and protected from unauthorized disclosure?

  • A. NDA
  • B. SoW
  • C. BoM
  • D. Hold Harmless
Show answer and explanation ▾

Correct answer: A

A non-disclosure agreement is the document that legally binds the parties to keep the customer's proprietary information confidential.

Why the other options are wrong:

  • B. A statement of work defines the scope and deliverables, not confidentiality.
  • C. A bill of materials lists equipment and has no confidentiality role.
  • D. A hold harmless agreement limits liability for damage and is not about disclosure of information.

Question 6

In WLAN location-based services, which metric, despite being commonly used, offers the lowest accuracy when determining device positions?

  • A. Angle of Arrival (AoA)
  • B. Time of Arrival (ToA)
  • C. Time Difference of Arrival (TDoA)
  • D. Received Signal Strength Indicator (RSSI)
Show answer and explanation ▾

Correct answer: D

RSSI is the most widely used location metric because every Wi-Fi radio already reports it. Signal strength varies with obstacles, multipath, client orientation and differences between chipsets, so distance estimates from RSSI are the least accurate of these methods.

Why the other options are wrong:

  • A. Angle of Arrival uses antenna arrays to measure the direction of the signal and gives better accuracy than signal strength.
  • B. Time of Arrival measures signal travel time and gives better accuracy than signal strength.
  • C. Time Difference of Arrival compares arrival times at several receivers and gives better accuracy than signal strength.

Question 7

Your customer uses PSK authentication but needs a more secure, certificate-based solution requiring certificates on both the client and server.

Which EAP method is the most appropriate?

  • A. EAP-FAST
  • B. EAP-TTLS
  • C. EAP-TLS
  • D. PEAP
Show answer and explanation ▾

Correct answer: C

EAP-TLS performs mutual authentication with X.509 certificates on both sides: the server presents its certificate and each client presents its own. It is the EAP method built on client and server certificates.

Why the other options are wrong:

  • A. EAP-FAST uses Protected Access Credentials and does not require a certificate on the client.
  • B. EAP-TTLS needs only a server certificate; the client authenticates inside the tunnel with another credential.
  • D. PEAP needs only a server certificate; the client usually authenticates inside the tunnel with a username and password.

Question 8

When designing a wireless bridge to connect two offices 13 kilometers (approximately 8 miles) apart, which factor must the Wireless Engineer consider to account for Fresnel Zone clearance?

  • A. Earth bulge
  • B. Antenna gain
  • C. FSPL
  • D. Receive sensitivity
Show answer and explanation ▾

Correct answer: A

On links longer than about 7 miles (11 kilometers) the curvature of the Earth rises into the path between the antennas. Earth bulge must be added to the obstacle height and Fresnel zone radius when the antenna heights are calculated.

Why the other options are wrong:

  • B. Antenna gain affects the link budget, not the physical clearance of the Fresnel zone.
  • C. Free space path loss affects the link budget, not the physical clearance of the Fresnel zone.
  • D. Receive sensitivity affects the link budget, not the physical clearance of the Fresnel zone.

Question 9

While conducting a site survey in a heavy machinery repair facility, what essential gear should you use for safety in this challenging environment?

  • A. Personal Protective Equipment (PPE)
  • B. Low gain antennas
  • C. Low power APs
  • D. Indoor APs
Show answer and explanation ▾

Correct answer: A

Industrial sites with heavy machinery present physical hazards. Personal Protective Equipment such as a hard hat, safety glasses, steel-toe boots and a high-visibility vest is required to work there safely and is usually mandated by the facility.

Why the other options are wrong:

  • B. Low gain antennas are a design choice and give the surveyor no protection.
  • C. Low power APs are a design choice and give the surveyor no protection.
  • D. Indoor APs are an equipment choice and give the surveyor no protection.

Question 10

A North American business traveler connects to a hotel’s 2.4 GHz SSID in Europe and notices low RSSI from an AP in the room, but experiences no issues with RSSI in the lobby.

What is the most likely reason for the low RSSI in the room?

  • A. The AP in the room is using ZigBee instead of Wi-Fi
  • B. The AP in the room is transmitting on channel 13 and the traveler associated to an AP on channels 1 through 11 in the lobby
  • C. The switchport that the AP is connected to is only capable of transmitting at 10 Mbps
  • D. The AP in the room is using Bluetooth instead of Wi-Fi
Show answer and explanation ▾

Correct answer: B

European 2.4 GHz networks may use channels 12 and 13, which North American client devices do not use. The traveler's device cannot join the room AP on channel 13, so it stays associated to a distant AP on channels 1 through 11 and shows a low RSSI in the room.

Why the other options are wrong:

  • A. A Wi-Fi SSID is not delivered over ZigBee, which is a different technology.
  • C. A 10 Mbps switchport limits wired throughput and has no effect on the RSSI the client measures.
  • D. A Wi-Fi SSID is not delivered over Bluetooth, which is a different technology.

Question 11

A museum requires its wireless access points to be discreetly integrated into the environment without sacrificing performance.

Which design choice best meets this requirement while maintaining optimal functionality?

  • A. Lock the AP inside of a metal box
  • B. Place the APs in between walls and I-beams
  • C. Use an 802.11b AP, so it looks old enough to be in a museum
  • D. Use a plastic cover that could blend in with the environment
Show answer and explanation ▾

Correct answer: D

A plastic cover or enclosure that matches the surroundings hides the AP while letting RF pass through with very little loss, so the design stays discreet and coverage is preserved.

Why the other options are wrong:

  • A. A metal box blocks and reflects RF and badly reduces coverage.
  • B. Walls and steel I-beams around the AP attenuate and reflect the signal and distort its coverage pattern.
  • C. An 802.11b AP gives very poor performance and is no less visible.

Question 12

An engineering firm upgraded from nine 802.11n APs to nine 802.11ac APs, retaining, the same channel and power configuration. Despite this, throughput remains unchanged.

What is the most likely reason for the lack of improvement?

  • A. APs are transmitting at a low transmit power
  • B. The clients were not upgraded
  • C. APs are mounted on the wall
  • D. The APs are still using the 5 GHz lower band
Show answer and explanation ▾

Correct answer: B

A link runs at the highest rates both ends support. If the clients are still 802.11n devices, they keep using 802.11n rates with the new APs, so throughput stays the same until the clients are upgraded too.

Why the other options are wrong:

  • A. Transmit power was kept the same as before, so it does not explain the missing improvement.
  • C. Wall mounting was not changed by the upgrade and does not prevent 802.11ac rates.
  • D. 802.11ac works across the whole 5 GHz band, including the lower channels.

Question 13

During a public Wi-Fi session with 10 other users, you run a ping sweep but cannot detect any devices on your subnet.

What feature is likely enabled on the WLAN infrastructure to prevent local communication between clients?

  • A. Peer-to-peer blocking
  • B. OSPF external routes
  • C. Band steering
  • D. Load balancing
Show answer and explanation ▾

Correct answer: A

Peer-to-peer blocking, also called client isolation, stops stations on the same WLAN from sending traffic directly to each other. Pings to other clients go unanswered, which is common on public hotspots to protect users from one another.

Why the other options are wrong:

  • B. OSPF external routes are a wired routing feature and do not stop clients on one subnet from reaching each other.
  • C. Band steering moves dual-band clients to another band and does not block traffic between clients.
  • D. Load balancing spreads clients across APs and does not block traffic between clients.

Question 14

While implementing 802.11ax APs in the 6 GHz band, a consultant recommends using WPA2-Personal for VoIP support.

Why is this approach technically inappropriate?

  • A. Because WPA2-Personal causes slower roams than WPA2-Enterprise
  • B. Because 802.11ax does not support WPA2-Personal in any band
  • C. Because 6 GHz WLANs cannot use WPA2-Personal
  • D. Because VoIP requires Opportunistic Wireless Encryption (OWE)
Show answer and explanation ▾

Correct answer: C

Wi-Fi operation in the 6 GHz band requires WPA3 or Enhanced Open with Protected Management Frames. WPA2-Personal is not permitted there, so a 6 GHz voice WLAN must use WPA3-Personal (SAE) or WPA3-Enterprise instead.

Why the other options are wrong:

  • A. Roaming speed is not the reason; WPA2-Personal cannot be used in 6 GHz at all.
  • B. 802.11ax devices can use WPA2-Personal in the 2.4 GHz and 5 GHz bands.
  • D. VoIP has no requirement for Opportunistic Wireless Encryption.

Question 15

While planning for a VoWLAN deployment requiring 25 dB SNR, you measure the noise floor at -88 dBm.

What is the minimum RSSI needed to meet the system’s performance requirements?

  • A. -70 dBM
  • B. -67 dBM
  • C. -65 dBM
  • D. -63 dBM
Show answer and explanation ▾

Correct answer: D

SNR is the received signal strength minus the noise floor. With a noise floor of -88 dBm and a required SNR of 25 dB, the signal must be at least -88 + 25 = -63 dBm.

Why the other options are wrong:

  • A. A signal of -70 dBm gives an SNR of only 18 dB over a -88 dBm noise floor.
  • B. A signal of -67 dBm gives an SNR of only 21 dB over a -88 dBm noise floor.
  • C. A signal of -65 dBm gives an SNR of only 23 dB over a -88 dBm noise floor.

Question 16

When deploying an Enterprise-class VoWLAN infrastructure, which Access Category (AC) must be used to prioritize voice packets and ensure optimal performance?

  • A. AC_VI
  • B. AC_VO
  • C. AC_BE
  • D. AC_BK
Show answer and explanation ▾

Correct answer: B

AC_VO is the voice access category in WMM and EDCA. It has the shortest arbitration interframe space and the smallest contention window, so voice frames get the highest priority access to the medium.

Why the other options are wrong:

  • A. AC_VI is the video access category and has lower priority than voice.
  • C. AC_BE is the best effort category used for ordinary data traffic.
  • D. AC_BK is the background category and has the lowest priority.

Question 17

When using a WLAN design tool with propagation modeling capabilities, what critical step must be performed before adding APs, antennas, and attenuation factors like walls?

  • A. Set the transmit power for all APs
  • B. Add pictures of the environment
  • C. Nothing just begin by adding APs, antennas and attenuators
  • D. Calibrate the floor plan to increase accuracy
Show answer and explanation ▾

Correct answer: D

The floor plan must be scaled first by entering a known distance, such as the length of a wall. Every propagation and attenuation calculation in the tool depends on correct distances, so an uncalibrated plan makes the whole prediction wrong.

Why the other options are wrong:

  • A. Transmit power is set on APs after they are placed on a scaled floor plan.
  • B. Pictures of the environment are useful documentation but do not affect the accuracy of the model.
  • C. Adding APs and walls before the plan is scaled produces predictions based on wrong distances.

Question 18

Your customer’s 802.11n laptops cannot detect the SSID in the 5 GHz band in a conference room, but your 802.11ac laptop connects without issue.

What is the most likely explanation for this discrepancy?

  • A. The AP is configured to use channel 36
  • B. The customer laptop does not support OFDM
  • C. The AP is on channel 144
  • D. Their laptops are SISO clients
Show answer and explanation ▾

Correct answer: C

Channel 144 was added to the 5 GHz channel plan after many 802.11n client devices had shipped, and many of them do not support it. Those laptops cannot see an AP on channel 144, while newer 802.11ac clients can.

Why the other options are wrong:

  • A. Channel 36 is supported by every 5 GHz client.
  • B. Every 802.11n device supports OFDM.
  • D. A single-stream client can still detect and join the SSID.

Question 19

When designing a static channel plan for an office using voice devices near an airport, which range of channels may be avoided channel switching when implemented in this environment?

  • A. 36-40
  • B. 44-48
  • C. 116-124
  • D. 1-11
Show answer and explanation ▾

Correct answer: D

Near an airport, radar can force APs on DFS channels to change channel, which interrupts voice calls. Channels 1 to 11 are in the 2.4 GHz band, which has no radar detection requirement, so APs on them are never moved by a radar event.

Why the other options are wrong:

  • A. Channels 36-40 are not the range this design relies on for voice devices near the airport.
  • B. Channels 44-48 are not the range this design relies on for voice devices near the airport.
  • C. Channels 116-124 are DFS channels and are subject to channel changes when radar is detected.

Question 20

Which vertically polarized antenna is best suited for a WLAN infrastructure with access points mounted on a ceiling over 6 meters high, where all client stations operate from the floor level?

  • A. Patch
  • B. Dish
  • C. Grid
  • D. Low-gain dipole
Show answer and explanation ▾

Correct answer: A

A patch antenna is semi-directional. Mounted on a high ceiling and aimed down, it focuses the signal toward the floor where the clients are, instead of spreading it out sideways at ceiling height.

Why the other options are wrong:

  • B. A dish is a highly directional antenna made for long point-to-point links.
  • C. A grid is a highly directional antenna made for long point-to-point links.
  • D. A low-gain dipole on a high ceiling radiates mostly sideways and delivers a weak signal to the floor.

Question 21

When using a predictive design tool, you have selected access points (APs) with an antenna gain of 3dBi and set the transmit power to 25 mW.

What is the EIRP (Effective Isotropic Radiated Power) of the APs in this design?

  • A. 11 dBm
  • B. 6.25 mW
  • C. 125 mW
  • D. 17 dBm
Show answer and explanation ▾

Correct answer: D

25 mW is about 14 dBm. EIRP is transmit power plus antenna gain, so 14 dBm + 3 dBi = 17 dBm, which is about 50 mW.

Why the other options are wrong:

  • A. 11 dBm would mean the antenna reduced the power by 3 dB instead of adding 3 dB.
  • B. 6.25 mW is lower than the transmit power, and a 3 dBi antenna increases EIRP.
  • C. A 3 dB gain doubles the power to about 50 mW; it does not multiply it by five.

Question 22

Your customer has selected switches that support 802.3bz MultiGig interfaces and 4x4:4 802.11ac Wave 2 APs with dual-5GHz capabilities. The APs have one MultiGig interface, and some cable runs will exceed 180.5 feet (55 meters). To support MultiGig speeds, which is the best cabling option?

  • A. Cat-5
  • B. Cat-6
  • C. Cat-5e
  • D. Cat-6a
Show answer and explanation ▾

Correct answer: D

Cat-6a is rated for up to 10 Gbps over the full 100 meters, so it supports every MultiGig speed on the longer runs and leaves headroom for future APs. It is the best cabling choice for a new MultiGig design.

Why the other options are wrong:

  • A. Cat-5 is not rated for MultiGig speeds.
  • B. Cat-6 does not give the full-distance 10 Gbps rating and headroom that Cat-6a provides.
  • C. Cat-5e offers the least MultiGig headroom of the usable categories and is not the best option for new runs.

Question 23

When conducting a site survey for a possible WLAN redesign, you use two Wi-Fi USB adapters for RSSI data collection and two USB spectrum analysis adapters for RF spectrum data. Since your laptop lacks enough USB ports, you connect them via a 4-port powered USB 3.0 hub. What issue could the use of USB 3.0 cause that might impact your site survey?

  • A. It does not give you enough bandwidth to collect data coming from all of the adapters
  • B. No USB 3.0 hub provides enough power for all the adapters
  • C. It generate noise in the 2.4 GHz band, giving you a false perception of the noise floor
  • D. It generates noise in the 5 GHz band, giving you a false perception of the noise floor
Show answer and explanation ▾

Correct answer: C

USB 3.0 ports, hubs and cables radiate broadband noise in the 2.4 GHz range. Adapters plugged into the hub pick up that noise, so the survey shows a raised 2.4 GHz noise floor that is not really present in the environment.

Why the other options are wrong:

  • A. USB 3.0 has ample bandwidth for four survey adapters.
  • B. A powered hub supplies its own power to the adapters.
  • D. USB 3.0 noise falls in the 2.4 GHz range, not the 5 GHz band.

That was 23 of 120.

The full CWNP CWDP-305 pack has all 120 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.

Get the full pack

Not ready yet? Get the first 23 free as one PDF by email. Get the Half Pack →

About the CWDP-305 exam

These 23 CWNP CWDP-305 questions are free here, and as a free PDF by email.

They are drawn from the same bank as the full CWDP-305 pack, which has 120 questions in total.

Back to blog