Cisco 800-150 FLDTEC Practice Questions with Explanations
Free Cisco 800-150 FLDTEC practice questions. 28 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.
800-150 practice questions
Question 1
What is the primary role of a switch in a local area network?
- A. to route data packets between different networks
- B. to encrypt data transmissions for security
- C. to divide the network into separate collision domains
- D. to provide wireless connectivity to LAN devices
Show answer and explanation ▾
Correct answer: C
A switch learns MAC addresses and gives each of its ports its own collision domain, so devices do not compete for the same wire.
Why the other options are wrong:
- A. Routing packets between networks is the job of a router.
- B. Encrypting data transmissions is not a switch function.
- D. Wireless connectivity for LAN devices is provided by an access point.
Question 2
Which Layer 2 technology extends to access layer devices, which allows individual switch ports to be assigned for network and traffic management in an enterprise network?
- A. BGP
- B. VLANs
- C. OSPF
- D. MPLS
Show answer and explanation ▾
Correct answer: B
VLANs are a Layer 2 technology that lets switch ports at the access layer be assigned to separate networks for traffic management.
Why the other options are wrong:
- A. BGP is a Layer 3 routing protocol used between autonomous systems.
- C. OSPF is a Layer 3 routing protocol.
- D. MPLS is a forwarding technology used mainly in provider and WAN networks, not for assigning access ports.
Question 3
Which scenario would result in a speed mismatch when configuring Ethernet devices with different speed settings?
- A. One end is manually set to 1 Gbps, and the other end is manually set to 100 Mbps.
- B. Both ends are manually set to the same speed.
- C. One end is manually set to 100 Mbps, and the other end is set to auto-negotiation.
- D. Both ends are set to auto-negotiation and fail, reverting to their lowest speeds.
Show answer and explanation ▾
Correct answer: A
A speed mismatch happens when both ends are hard-set to different speeds, such as 1 Gbps on one side and 100 Mbps on the other, because the link cannot come up at a speed both accept.
Why the other options are wrong:
- B. Both ends set to the same speed match, so there is no mismatch.
- C. An auto-negotiating end can detect the speed of a fixed 100 Mbps partner and match it.
- D. If both ends fall back to their lowest speed they still agree on one speed, so there is no mismatch.
Question 4
Which layer of the OSI model provides error detection and defines how access to the media is controlled?
- A. presentation layer
- B. physical layer
- C. network layer
- D. data link layer
Show answer and explanation ▾
Correct answer: D
The data link layer, Layer 2, adds frame error detection and controls access to the media. The other layers handle data format, bit signalling and routing.
Why the other options are wrong:
- A. The presentation layer handles data formatting and encryption, not media access.
- B. The physical layer moves raw bits and does not check frames for errors.
- C. The network layer handles logical addressing and routing, not media access.
Question 5
Which two devices are most commonly used in a WAN environment? (Choose two.)
- A. hubs
- B. optical fiber converters
- C. modems
- D. network interface cards
- E. wireless access points
Show answer and explanation ▾
Correct answer: B, C
Optical fiber converters and modems connect sites over long-distance carrier links, so they are typical WAN devices. They convert signals between the local network and the provider medium.
Why the other options are wrong:
- A. Hubs repeat signals inside a local segment and are not WAN devices.
- D. Network interface cards connect individual hosts to a LAN.
- E. Wireless access points provide local wireless coverage, not WAN connectivity.
Question 6
What is the purpose of a subnet mask?
- A. distinguishes the network and host segments
- B. provides encryption for network traffic
- C. determines the next-hop router
- D. aids end route prioritization
Show answer and explanation ▾
Correct answer: A
A subnet mask marks which bits of an IP address identify the network and which identify the host. Devices use it to decide whether a destination is local or must go through a router.
Why the other options are wrong:
- B. A subnet mask does not encrypt traffic.
- C. The next-hop router is chosen from the routing table, not by the subnet mask.
- D. A subnet mask does not prioritize routes or traffic.
Question 7
When should a crossover UTP cable be used instead of a straight-through cable when connecting network devices?
- A. to connect electrically like devices
- B. to connect a PC to a wireless access point
- C. to connect a switch to a router
- D. to connect electrically unlike devices
Show answer and explanation ▾
Correct answer: A
A crossover cable swaps the transmit and receive pairs, so it connects devices that use the same pins to transmit, such as switch to switch or PC to PC. Straight-through cables join unlike devices.
Why the other options are wrong:
- B. Connecting a PC to a wireless access point names one device pairing, not the rule that decides when a crossover cable is needed.
- C. A switch and a router are unlike devices, so a straight-through cable is used.
- D. Unlike devices connect with a straight-through cable, not a crossover cable.
Question 8
How many bits are borrowed from the default host portion of the address to create subnets in a Class B network with a subnet mask 255.255.255.0?
- A. 3 bits
- B. 5 bits
- C. 8 bits
- D. 11 bits
Show answer and explanation ▾
Correct answer: C
A Class B network has a default mask of 255.255.0.0. The mask 255.255.255.0 adds the whole third octet to the network portion, so 8 bits are borrowed from the host portion.
Why the other options are wrong:
- A. Borrowing 3 bits would give a mask ending in 224 in the third octet.
- B. Borrowing 5 bits would give a mask ending in 248 in the third octet.
- D. Borrowing 11 bits would extend the mask into the fourth octet.
Question 9
What is the function of an access layer device?
- A. provides high-speed data transport between buildings or different parts of the campus
- B. serves as the entry point for end-user devices to connect to the network
- C. provides secure external access to internal network components
- D. connects remote offices to the main corporate network
Show answer and explanation ▾
Correct answer: B
The access layer is where end-user devices such as PCs, phones and access points attach to the network. Access switches provide that entry point.
Why the other options are wrong:
- A. High-speed transport between buildings is a core layer role.
- C. Secure external access is provided by edge and security devices, not the access layer.
- D. Connecting remote offices to the main network is a WAN edge role.
Question 10
Which term describes the physical range of radio frequency coverage provided by an access point in a wireless topology?
- A. Service Set Identifier (SSID)
- B. Basic Service Area (BSA)
- C. Wireless LAN (WLAN)
- D. Wireless LAN Controller (WLC)
Show answer and explanation ▾
Correct answer: B
The Basic Service Area is the physical area of radio frequency coverage provided by a single access point. Clients inside it can associate with that access point.
Why the other options are wrong:
- A. An SSID is the name of a wireless network, not a coverage area.
- C. A WLAN is the wireless network as a whole, not the range of one access point.
- D. A wireless LAN controller manages access points and does not define coverage.
Question 11
Which two configuration parameters are most critical to ensure optimal performance when configuring a network port for a newly installed IP phone in an enterprise environment? (Choose two.)
- A. VLAN assignment
- B. link aggregation
- C. Spanning Tree Protocol
- D. Power over Ethernet
- E. QoS classification
Show answer and explanation ▾
Correct answer: A, D
An IP phone needs power, which Power over Ethernet supplies over the same cable, and it needs the right VLAN assignment so voice traffic lands on the correct network.
Why the other options are wrong:
- B. Link aggregation bundles links between network devices and is not used for a single phone port.
- C. Spanning Tree Protocol is a loop-prevention feature and is not one of the two most critical phone port settings.
- E. QoS classification does not power the phone or place its traffic on the correct VLAN, which the phone needs before it can work on the port.
Question 12
Which deployment scenarios are Cisco 8000 Series routers primarily designed for?
- A. remote branch offices and retail locations
- B. service provider and web-scale networks
- C. small business and home office networks
- D. campus LAN access and distribution layers
Show answer and explanation ▾
Correct answer: B
Cisco 8000 Series routers are high-capacity platforms built for service provider and web-scale networks. They are not aimed at branch, small office or campus access roles.
Why the other options are wrong:
- A. Branch and retail sites use smaller routing platforms rather than the 8000 Series.
- C. Small business and home office networks use much smaller devices.
- D. Campus access and distribution layers are served by switches, not by 8000 Series routers.
Question 13
Which Cisco switch series is designed to handle the combined responsibilities of core and distribution layers in a converged architecture?
- A. Meraki MS400 Series
- B. Catalyst 6500 E-Series
- C. Catalyst 1300 Series
- D. Catalyst 9000 Series
Show answer and explanation ▾
Correct answer: D
The Catalyst 9000 Series is Cisco's current enterprise switching family and covers access through core, including a converged core and distribution design.
Why the other options are wrong:
- A. The Meraki MS400 Series is a cloud-managed switch family and is not the series designed for this converged role.
- B. The Catalyst 6500 E-Series is an older modular platform, not the series designed for this converged core and distribution role.
- C. The Catalyst 1300 Series is a small business access switch family.
Question 14
Which command is used to download a copied configuration file from a TFTP server to merge it with the running configuration of a replacement Cisco device?
- A. load tftp: running-config
- B. copy tftp: startup-config
- C. copy tftp: running-config
- D. merge tftp: running-config
Show answer and explanation ▾
Correct answer: C
Copying a file from tftp: to running-config merges it into the active configuration rather than replacing it. This is the usual way to apply a saved configuration to a replacement device.
Why the other options are wrong:
- A. There is no load tftp: running-config command on Cisco IOS.
- B. Copying to startup-config writes to NVRAM and does not merge into the running configuration.
- D. There is no merge command in IOS for this task.
Question 15
What is the primary purpose of backing up the endpoint configuration prior to replacing the device?
- A. to troubleshoot network connectivity issues
- B. to update the firmware of the device
- C. to generate a performance report for the old device
- D. to restore settings on the new device after replacement
Show answer and explanation ▾
Correct answer: D
A saved configuration lets the technician load the same settings onto the replacement device so it takes over the old device's role quickly.
Why the other options are wrong:
- A. A backup file does not troubleshoot connectivity.
- B. A configuration backup does not update firmware.
- C. Performance reports come from monitoring tools, not configuration backups.
Question 16
Which two settings are standard Cisco console connections when configuring a terminal emulator to connect to the console port of a Cisco switch? (Choose two.)
- A. Stop bits: 2
- B. Flow control: Hardware
- C. Speed (baud rate): 9600
- D. Data bits: 8
- E. Parity: Even
Show answer and explanation ▾
Correct answer: C, D
The standard Cisco console settings are 9600 baud, 8 data bits, no parity, 1 stop bit and no flow control. Speed 9600 and 8 data bits are the two that match.
Why the other options are wrong:
- A. The standard setting is 1 stop bit, not 2.
- B. The standard setting uses no flow control rather than hardware flow control.
- E. The standard setting uses no parity, not even parity.
Question 17
What is the primary purpose of changing the configuration register when performing password recovery?
- A. to erase the entire configuration
- B. to ignore the startup configuration
- C. to unlock all user accounts
- D. to enable advanced debugging features
Show answer and explanation ▾
Correct answer: B
Changing the configuration register, typically to 0x2142, makes the device skip the startup configuration at boot. The technician can then reach the device without the saved passwords and reset them.
Why the other options are wrong:
- A. Changing the register does not erase any configuration.
- C. User accounts are not unlocked by the configuration register.
- D. The register change is not used to enable debugging.
Question 18
Which command prompt commands provide the most thorough network diagnostic information when troubleshooting connectivity issues between a Windows PC and a Cisco device?
- A. ipconfig /all ping netstat -a
- B. netsh wlan show interfaces ipconfig /release ipconfig /renew
- C. ping traced netstat
- D. nslookup arp -a route print
Show answer and explanation ▾
Correct answer: A
ipconfig /all shows full addressing details, ping tests reachability to the device, and netstat -a lists connections and listening ports. Together they give the broadest picture of connectivity.
Why the other options are wrong:
- B. These commands focus on wireless status and renewing the address, not on broad diagnostics.
- C. traced is not a valid Windows command, so this set is not usable.
- D. These commands cover name resolution, ARP and routes but not address configuration or reachability testing.
Question 19
Which mode must the console terminal of the device be in before a prewritten configuration is pasted to transfer the configuration from an old device to a new one?
- A. interface configuration mode
- B. global configuration mode
- C. privileged EXEC mode
- D. user EXEC mode
Show answer and explanation ▾
Correct answer: B
Pasted configuration commands such as hostname, interface and line settings are global configuration commands, so the terminal must be in global configuration mode first.
Why the other options are wrong:
- A. Interface configuration mode applies commands only to one interface.
- C. Privileged EXEC mode does not accept configuration commands.
- D. User EXEC mode is limited and does not accept configuration commands.
Question 20
Which command is used to copy the startup configuration of a device to a USB file system when transferring files to a Cisco device?
- A. Router# copy startup-config tftp://[server_ip]/[destination_fiie]
- B. Router# copy usbflash0:[filename] startup-config
- C. Router# copy startup-config usbflash0:[filename]
- D. Router# copy running-config usbflash0:[filename]
Show answer and explanation ▾
Correct answer: C
copy startup-config usbflash0:[filename] copies the startup configuration from NVRAM to the USB file system, with the source first and the destination second.
Why the other options are wrong:
- A. This command sends the startup configuration to a TFTP server, not a USB drive.
- B. This command copies from USB into the startup configuration, the reverse direction.
- D. This command copies the running configuration, not the startup configuration.
Question 21
Which two actions are typically performed in ROMMON mode during the password recovery process? (Choose two.)
- A. Change the configuration register.
- B. Load the startup configuration.
- C. Save the configuration.
- D. Modify passwords.
- E. Reboot the device.
Show answer and explanation ▾
Correct answer: A, E
In ROMMON the technician changes the configuration register so the startup configuration is ignored, then reboots the device to continue recovery.
Why the other options are wrong:
- B. Loading the startup configuration happens after the reboot in the IOS boot process, not in ROMMON.
- C. The configuration is saved from the IOS CLI after the device has booted.
- D. Passwords are modified from the IOS CLI after booting, not in ROMMON.
Question 22
Which action must be taken when editing a captured configuration of an old device for reuse in a replacement device?
- A. Remove all configurations under line vty 0 4.
- B. Retain all username entries.
- C. Keep all access-list commands intact.
- D. Add the enable password cisco command.
Show answer and explanation ▾
Correct answer: A
Removing the line vty 0 4 settings from the captured configuration avoids carrying over remote access settings that may not suit the replacement device, so they can be set fresh.
Why the other options are wrong:
- B. Username entries should not be retained blindly from the old device.
- C. Access-list commands should be reviewed rather than kept intact without checking.
- D. Adding an enable password of cisco would create a weak, well-known password.
Question 23
Which command provides a concise look at important switch port characteristics, such as port ID. VLAN, duplex, speed, and media type?
- A. show cdp neighbors
- B. show interface status
- C. show controllers
- D. show ip interface brief
Show answer and explanation ▾
Correct answer: B
show interface status gives a one-line summary per port with port ID, VLAN, duplex, speed and media type.
Why the other options are wrong:
- A. show cdp neighbors lists directly connected Cisco devices.
- C. show controllers displays hardware-level interface details.
- D. show ip interface brief shows IP addresses and up or down status, not duplex, speed and media type.
Question 24
Which type of license is locally managed and does not require external tools for management?
- A. hybrid licenses
- B. PAK licenses
- C. RTU licenses
- D. smart licenses
Show answer and explanation ▾
Correct answer: C
Right-to-use licenses are managed locally on the device and need no external tool or server to manage them.
Why the other options are wrong:
- A. Hybrid licenses are not the locally managed type.
- B. PAK licenses require registering a product authorization key with Cisco.
- D. Smart licenses are managed through Cisco's Smart Licensing.
Question 25
Which common CLI command is used to install Cisco NX-OS Software?
- A. copy tftp running-config
- B. install all
- C. install kickstart
- D. boot system
Show answer and explanation ▾
Correct answer: B
install all is the Cisco NX-OS command that installs a new software image on the device and checks compatibility before it performs the upgrade.
Why the other options are wrong:
- A. This command copies a configuration file to the running configuration.
- C. install kickstart is not the common command used to install NX-OS Software.
- D. boot system sets the image to boot but is not the install command.
Question 26
Which management option is best suited for standalone Cisco Secure Firewall deployments?
- A. Cisco Secure Firewall Management Center
- B. Cisco Defense Orchestrator
- C. Cisco Security Manager
- D. Cisco Secure Firewall Device Manager
Show answer and explanation ▾
Correct answer: D
Cisco Secure Firewall Device Manager is the on-box manager designed for a single standalone firewall.
Why the other options are wrong:
- A. Management Center is designed for managing many firewalls.
- B. Cisco Defense Orchestrator is a cloud-based multi-device management service.
- C. Cisco Security Manager is a multi-device management application.
Question 27
What is the main advantage of using Bundle mode when installing Cisco IOS XE Software on a switch?
- A. automatic creation of the packages.conf file
- B. simplicity, with no need to manage individual packages
- C. faster boot times compared to Install mode
- D. ability to install and upgrade packages independently
Show answer and explanation ▾
Correct answer: B
In Bundle mode the switch boots directly from a single .bin image, so there are no individual packages to manage.
Why the other options are wrong:
- A. Creating packages.conf is part of Install mode, not Bundle mode.
- C. Bundle mode is not the faster booting option.
- D. Installing packages independently is a feature of Install mode.
Question 28
What is the purpose of the packages.conf file in Install mode on Cisco IOS XE Software supported switches?
- A. It is used to extract the .bin file during the installation process.
- B. It determines which software packages need to be loaded and in what order during boot up.
- C. It contains the entire bundled software image in a single file.
- D. It is a subdirectory in flash memory where individual software packages are stored.
Show answer and explanation ▾
Correct answer: B
In Install mode, packages.conf lists the software packages and the order in which the switch loads them at boot.
Why the other options are wrong:
- A. The .bin file is extracted by the install command, not by packages.conf.
- C. The bundled image in a single file is the .bin file used in Bundle mode.
- D. packages.conf is a file, not a subdirectory.
That was 28 of 100.
The full Cisco 800-150 FLDTEC pack has all 100 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.
Get the full packNot ready yet? Get the first 39 free as one PDF by email. Get the Half Pack →
About the 800-150 exam
These 28 Cisco 800-150 FLDTEC questions are free here. The free PDF has 39, free by email.
They are drawn from the same bank as the full 800-150 pack, which has 100 questions in total.