Cisco 350-101 WLCOR Practice Questions with Explanations

Free Cisco 350-101 WLCOR practice questions. 26 of them, each with the correct answer, a full explanation, and the reason every other option is wrong.

350-101 practice questions

Question 1

What defines device sensitivity in a wireless environment?

  • A. capability to process the signal
  • B. detection of redundant gateways
  • C. synchronization of beacon intervals
  • D. implementation of key refresh schedules
Show answer and explanation ▾

Correct answer: A

Sensitivity describes how weak a signal a receiver can still decode. It is a measure of the device's ability to process the signal it receives.

Why the other options are wrong:

  • B. Finding redundant gateways is a routing function, not an RF property of a device.
  • C. Beacon interval timing is a network setting and does not define receiver sensitivity.
  • D. Key refresh schedules are a security setting, not an RF measure.

Question 2

How does U-NII-1 operate with regards to the common frequency bands supported in enterprise wireless networks?

  • A. It uses a range of higher frequencies and tile enforcement with static power configuration.
  • B. It uses a range of lower frequencies with restrictions on transmit power used indoor and outdoor.
  • C. It defines subsections with signal handling and is restricted to indoor use helping minimize interference.
  • D. It defines class limits for specialty devices and is restricted to outdoor use increasing coverage.
Show answer and explanation ▾

Correct answer: C

U-NII-1 is the lowest of the 5 GHz U-NII subsections, each of which has its own operating rules. Regulators have long treated it as an indoor band, and European rules still limit 5150 to 5250 MHz to indoor use, which helps minimize interference with other users of the spectrum.

Why the other options are wrong:

  • A. U-NII-1 sits at the low end of the 5 GHz band, so it is not a range of higher frequencies.
  • B. This option does not describe the subsection and indoor-use rules that define U-NII-1 here.
  • D. U-NII-1 is not an outdoor-only band for specialty devices.

Question 3

What is a characteristic of 20 MHz channel width in a wireless network?

  • A. narrowest channel width in the 2.4 band
  • B. increases authentication handoff frequency
  • C. supports automatic client reassociation
  • D. higher throughput than wider channels
Show answer and explanation ▾

Correct answer: A

A 20 MHz channel is the narrowest width available in the 2.4 GHz band. Wider channels such as 40 MHz would overlap far more of the few non-overlapping channels in that band.

Why the other options are wrong:

  • B. Handoff frequency depends on client movement and roaming, not on channel width.
  • C. Client reassociation is a roaming function and is not tied to channel width.
  • D. Wider channels carry more data than 20 MHz channels when conditions allow, not less.

Question 4

What does a high SNR value result in?

  • A. presence of multipath signal distortion
  • B. use of directional array patterns in wireless signaling
  • C. increased data integrity with fewer errors
  • D. modification of output frequency ranges
Show answer and explanation ▾

Correct answer: C

A high signal-to-noise ratio means the signal is well above the noise floor, so the receiver can decode frames more reliably. That gives better data integrity with fewer errors and retries.

Why the other options are wrong:

  • A. Multipath comes from reflections in the environment and is not caused by a high SNR.
  • B. Directional antenna patterns are an antenna design choice, not a result of SNR.
  • D. The output frequency range is set by the radio and channel, not by the SNR.

Question 5

What is the time taken for an RF signal to travel from the transmitter to the receiver known as?

  • A. reflection
  • B. propagation delay
  • C. scattering
  • D. link speed
Show answer and explanation ▾

Correct answer: B

Propagation delay is the time an RF signal takes to travel from the transmitter to the receiver. It depends on distance and the speed of the signal through the medium.

Why the other options are wrong:

  • A. Reflection is a signal bouncing off a surface, not the time the signal takes to travel.
  • C. Scattering is a signal spreading in many directions off a rough surface, not a travel time.
  • D. Link speed is a data rate, not the time a signal takes to cross the path.

Question 6

To double the range of a transmitter, which value must the transmitter be changed to if it is currently at 17 dBm?

  • A. 14 dBm
  • B. 20 dBm
  • C. 27 dBm
  • D. 100 dBm
Show answer and explanation ▾

Correct answer: C

Doubling range takes about 6 dB more power outdoors and about 9 dB indoors. Of the options, only 27 dBm, a 10 dB or tenfold increase over 17 dBm, adds enough power to double the range.

Why the other options are wrong:

  • A. 14 dBm is a 3 dB decrease, which halves the power and shortens the range.
  • B. 20 dBm is only a 3 dB increase, which doubles the power but does not double the range.
  • D. 100 dBm is far beyond any realistic transmitter power and is not the value needed.

Question 7

Which result is produced using a power ratio of 10:1 in standard decibel calculations?

  • A. -20 dB
  • B. 5 dB
  • C. 10 dB
  • D. 15 dB
Show answer and explanation ▾

Correct answer: C

A decibel is ten times the base 10 logarithm of a power ratio. A ratio of 10:1 gives 10 times log10(10), which is 10 dB.

Why the other options are wrong:

  • A. -20 dB is a loss of 100 times in power, not a 10:1 ratio.
  • B. 5 dB corresponds to a ratio of about 3.2:1, not 10:1.
  • D. 15 dB corresponds to a ratio of about 31.6:1, not 10:1.

Question 8

What is the primary modulation technology used by 802.11ax in wireless communications?

  • A. frequency hopping spread spectrum
  • B. direct sequence spread spectrum
  • C. orthogonal frequency-division multiple access
  • D. Quadrature Amplitude Modulation OFDMA
Show answer and explanation ▾

Correct answer: C

802.11ax (Wi-Fi 6) uses OFDMA, which divides a channel into resource units so that several clients can be served in the same transmission. It builds on OFDM subcarriers with QAM modulation.

Why the other options are wrong:

  • A. Frequency hopping spread spectrum was used by the original 802.11 radios, not by 802.11ax.
  • B. Direct sequence spread spectrum belongs to the original 802.11 and 802.11b radios, not 802.11ax.
  • D. QAM is a modulation scheme, and this combined name is not the primary technology identified for 802.11ax.

Question 9

Which process enables seamless Layer 2 handoff in a wireless network during roaming?

  • A. increased beacon interval setting
  • B. optimized roaming
  • C. fast BSS transition protocol
  • D. deferred probe response technique
Show answer and explanation ▾

Correct answer: C

Fast BSS Transition (802.11r) lets a client roam between APs without a full reauthentication, which keeps the Layer 2 handoff quick and seamless. The APs in the mobility domain share the needed security material in advance.

Why the other options are wrong:

  • A. A longer beacon interval only sends beacons less often and does not speed up roaming.
  • B. Optimized roaming is not the protocol that provides a seamless Layer 2 handoff.
  • D. Deferring probe responses is not a roaming method and would slow client discovery.

Question 10

Which Cisco Ultra-Reliable Wireless Backhaul process enables devices to establish a reliable connection with the next AP along their path before losing connectivity to the current one in a wireless network during roaming?

  • A. open roaming
  • B. fast client handoff
  • C. 802.11v high speed roaming
  • D. make-before-break handover logic
Show answer and explanation ▾

Correct answer: D

Make-before-break handover logic in Cisco Ultra-Reliable Wireless Backhaul lets a device set up a link to the next AP before it drops the current one. That keeps the connection continuous while moving.

Why the other options are wrong:

  • A. OpenRoaming is a federation for automatic Wi-Fi sign-on, not the backhaul handover process.
  • B. Fast client handoff is not the named process that links to the next AP before leaving the current one.
  • C. 802.11v high speed roaming is not the Ultra-Reliable Wireless Backhaul handover process.

Question 11

A deployment requires that several APs be connected to edge switches, and each AP must support management and guest Wi-Fi traffic. The APs tag guest traffic separately from management and the organization expects to add more VLANs for IoT and voice soon, so the configuration must support scalability. The security team requires that guest traffic never mix with internal resources.

Which port configuration must be used for the switch interfaces that connect to the APs?

  • A. Configure the central Layer 3 switch port as an access VLAN port that allows the management VLAN only.
  • B. Implement switch port access with the native VLAN for guest traffic and trunk with the management VLAN.
  • C. Set a trunk port with the management VLAN as the native VLAN, and allow only management and user VLANs.
  • D. Make the port an access port on the management VLAN because all traffic is tunneled back to the WLC.
Show answer and explanation ▾

Correct answer: C

A trunk port carries multiple VLANs, so the AP can tag guest traffic apart from management and more VLANs can be added later. Making management the native VLAN and allowing only the needed VLANs keeps guest traffic from mixing with internal resources.

Why the other options are wrong:

  • A. An access port for the management VLAN only cannot carry separately tagged guest traffic.
  • B. Mixing an access port with a guest native VLAN does not give a scalable trunk for added VLANs.
  • D. An access port on one VLAN cannot carry separately tagged guest traffic or future VLANs.

Question 12

An engineer has been tasked with configuring a Cisco Catalyst 9100 AP to join a WLC using a static configuration as DHCP and DNS discovery methods are not available. The engineer has set the AP hostname to 'AP0512345678', and has configured the AP with a static IP address, subnet mask, and default gateway. The engineer must now configure the AP to discover the primary WLC with hostname 'WLC-PRIMARY' and IP address '192.168.100.10'.

Which CLI command must the engineer use on the AP?

  • A. capwap ap WLC-PRIMARY 192.168.100.10
  • B. ap primary-base WLC-PRIMARY capwap 192.168.100.10
  • C. capwap ap primary-base 192.168.100.10
  • D. capwap ap primary-base WLC-PRIMARY 192.168.100.10
Show answer and explanation ▾

Correct answer: D

On the AP CLI, capwap ap primary-base takes the controller name followed by its IP address. This statically tells the AP which WLC to join when DHCP and DNS discovery are unavailable.

Why the other options are wrong:

  • A. This form leaves out the primary-base keyword, so it does not set the primary controller.
  • B. This puts the keywords in an order the AP CLI does not accept.
  • C. This leaves out the controller name that the command needs before the IP address.

Question 13

A network engineer has been tasked with migrating the management mode of a Cisco 9176 AP named "Cisco-AP053540555" in a large enterprise wireless deployment. The AP is currently managed by a Cisco Catalyst 9800 Series WLC, but the organization is transitioning to Meraki cloud management for centralized control and monitoring. To complete this migration, the engineer needs to change the AP's management mode to Meraki with force and noprompt to skip validations using the CLI on the wireless controller.

What command must the engineer use?

  • A. management meraki force noprompt mode
  • B. ap management mode meraki force noprompt
  • C. ap management meraki force noprompt mode
  • D. management-mode meraki force noprompt
Show answer and explanation ▾

Correct answer: B

The change is made on the 9800 in privileged EXEC mode with the ap name command for the AP followed by management-mode meraki force noprompt. The force keyword skips the controller validations and noprompt skips the confirmation prompt.

Why the other options are wrong:

  • A. This form starts with management and ends with mode, which is not the command structure.
  • C. This form puts mode after noprompt, so the keywords are out of order.
  • D. This form leaves out the ap keyword that the command starts with.

Question 14

A retail store has a Cisco 9176 FlexConnect AP at a branch location and must ensure that wireless clients continue to access the network even if the WAN link to the central controller is down. The AP must authenticate users locally during outages and still sync with the controller when connectivity is restored. The IT administrator wants centralized management for all APs but requires high availability for branch users.

Which set of CLI commands on the 9800 WLC configures the AP to meet these requirements?

  • A. config wlan branch1 flexconnect local-switching
  • B. config wireless local ap vlan 6 wlan branch1
  • C. wireless profile policy outage flexconnect local authentication
  • D. wireless profile policy outage no central authentication
Show answer and explanation ▾

Correct answer: D

Removing central authentication in the policy profile lets a FlexConnect AP authenticate clients locally when the WAN to the controller is down. The AP still stays managed by the controller and syncs again once the link returns.

Why the other options are wrong:

  • A. This is an AireOS-style command, not the 9800 policy profile setting for local authentication.
  • B. This is not a 9800 command and does not configure local authentication.
  • C. This is not the policy profile setting that lets the AP authenticate clients locally.

Question 15

A hotel wants to provide guests with wireless connectivity via a captive portal using a Cisco 9800 WLC. The solution must meet these requirements:

Ensure that guests are redirected to a custom web page for login and after authentication must have only internet access.

The guest SSID must not require a password and must be visible to all clients.

Network segmentation between staff and guests is required at the VLAN level.

What must the IT team configure on the WLAN?

  • A. central web authentication with WPA2-PSK security and a DNS ACL assigned to the WLAN profile
  • B. open authentication with a local web server for the guest WLAN
  • C. PSK WLAN with VLAN override and enable mDNS for guest users
  • D. central web authentication and assign a policy with ACLs restricting access to internal networks
Show answer and explanation ▾

Correct answer: D

Central web authentication on an open, broadcast SSID redirects guests to a custom login portal without a password. A policy with ACLs that block internal networks, on the guest VLAN, leaves guests with internet access only and keeps them apart from staff.

Why the other options are wrong:

  • A. WPA2-PSK requires a password, which the guest SSID must not have.
  • B. A local web server alone does not apply the policy and ACLs that limit guests to the internet.
  • C. A PSK WLAN requires a password, and mDNS has nothing to do with portal login.

Question 16

A network engineer must ensure that guest users connecting to a Cisco 9800 WLC are assigned IP addresses from a specific subnet that is separate from corporate users. The guest network must support at least 200 simultaneous connections and isolate traffic from internal devices.

The DHCP server must allocate addresses only within the 10.20.30.0/24 subnet.

Which action must the network engineer take to accomplish this task?

  • A. Set up a unique policy tag on the guest WLAN and use a shared DHCP pool.
  • B. Create a dedicated guest interface and map it to the guest policy profile for the guest WLAN.
  • C. Assign a unique policy tag to the guest WLAN and use a shared DHCP pool with DHCP option 43.
  • D. Use static IP address assignment for the guest WLAN interface and use ACLs for separation.
Show answer and explanation ▾

Correct answer: B

A dedicated guest interface, mapped to the guest policy profile, places guest clients in their own VLAN and subnet. That gives the separate 10.20.30.0/24 addressing and isolation from corporate users.

Why the other options are wrong:

  • A. A shared DHCP pool would not limit guests to their own subnet.
  • C. A shared pool does not separate guests, and option 43 is used for AP controller discovery, not guest addressing.
  • D. Static addressing does not scale to 200 clients, and ACLs alone do not provide a separate subnet.

Question 17

A medium-sized enterprise must provide wireless internet to visitors in their lobby using a Cisco 9800 WLC. The solution must meet these requirements:

Ensure that guests cannot access the corporate LAN.

Guests are redirected to a login page before browsing.

The guest network must use a separate VLAN from internal users.

Access must be limited to web browsing only.

Guest access does not require any preshared keys or certificates.

Which two actions must be taken to achieve this solution? (Choose two.)

  • A. Apply a webauth WLAN with mDNS mode set to drop.
  • B. Configure a policy profile that uses an external only ACL and guest VLAN.
  • C. Implement a policy profile with p2p blocking enabled and a guest VLAN.
  • D. Deploy a WLAN policy that points wireless users to a webauth parameter map.
  • E. Create a WLAN that uses a web policy and points to a consent parameter map.
Show answer and explanation ▾

Correct answer: B, D

A WLAN that points users to a webauth parameter map redirects guests to a login page without any key or certificate. A policy profile with a guest VLAN and an ACL that allows only external traffic keeps guests off the corporate LAN and limits them to web browsing.

Why the other options are wrong:

  • A. Dropping mDNS limits service discovery and does not restrict guests to browsing or separate them by VLAN.
  • C. Peer-to-peer blocking stops client to client traffic but does not block the corporate LAN or limit guests to browsing.
  • E. A consent parameter map only asks guests to accept terms and does not present the login page required.

Question 18

Users report slowness on the network, and it is suspected that certain applications are consuming all the bandwidth. A network engineer must enable the NBAR protocol to improve wireless client traffic visibility and provide advanced, granular, application classification, and analytics.

How should the network engineer configure NBAR on a 9800 WLC?

  • A. Enable NBARv2 on the WLAN.
  • B. Enable deep packet inspection on the WLAN.
  • C. Configure packet inspection on the policy profile.
  • D. Configure AVC on the policy profile.
Show answer and explanation ▾

Correct answer: D

On the 9800, NBAR2-based Application Visibility and Control is enabled by attaching an AVC flow monitor to the policy profile. That gives per-application classification and statistics for the wireless clients using that profile.

Why the other options are wrong:

  • A. NBAR is not turned on as an NBARv2 setting on the WLAN on the 9800.
  • B. Deep packet inspection is not a WLAN setting on the 9800 for application classification.
  • C. Packet inspection is not the policy profile setting; application visibility on the policy profile is configured as AVC.

Question 19

An engineer is migrating to a new Cisco Catalyst CW9800-H1 WLC to modernize the wireless infrastructure and enable advanced monitoring capabilities. The organization operates more than 150 access points and uses Cisco Catalyst Center for centralized network management and assurance. As part of the deployment, the engineer must enable wireless service assurance and wireless telemetry to monitor client connectivity, roaming behavior, and performance metrics across the wireless network.

Which configuration must be applied in Cisco Catalyst Center when onboarding the WLC?

  • A. Configure CLI and SNMP credentials and the NETCONF port during device discovery and ensure that device controllability is enabled under device settings. When discovered, assign the WLC and APs to a site with wireless telemetry enabled.
  • B. Configure CLI and SNMP credentials and the NETCONF port during device discovery and ensure that wireless telemetry is enabled under system settings. When discovered, assign the WLC to a site with device controllability enabled.
  • C. Enable CLI, SNMP, and NETCONF credentials during device discovery and ensure that wireless assurance is enabled globally. When discovered, assign the WLC to a site with device controllability enabled.
  • D. Enable CLI, SNMP, and NETCONF credentials during device discovery and ensure that device controllability is enabled globally. When discovered, assign the WLC to a site with wireless assurance enabled.
Show answer and explanation ▾

Correct answer: A

Catalyst Center discovers the WLC with CLI and SNMP credentials and the NETCONF port, and device controllability under device settings lets it push the configuration that assurance needs. Assigning the WLC and its APs to a site with wireless telemetry enabled then starts the telemetry used for client and roaming analytics.

Why the other options are wrong:

  • B. Wireless telemetry is set for the site, and device controllability is not assigned per site.
  • C. Discovery asks for a NETCONF port rather than separate NETCONF credentials, and device controllability is not assigned per site.
  • D. Discovery asks for a NETCONF port rather than separate NETCONF credentials, and the APs must also be in a site with wireless telemetry enabled.

Question 20

A wireless engineer must manage scheduled maintenance for a guest WLAN that uses Cisco Catalyst Center as the primary monitoring solution.

The engineer must coordinate downtime and verify that all services resume as intended after planned tasks are complete. The network supports multiple high-availability configurations and relies heavily on consistent visibility into device health. Event logging and alerting must be ensured throughout maintenance windows, and the maintenance process must be centrally managed.

Which process meets the requirements?

  • A. Monitor the Device 360 dashboard.
  • B. Monitor the device in Cisco Spaces.
  • C. Use the WLC dashboard.
  • D. Use scheduled maintenance for the device.
Show answer and explanation ▾

Correct answer: D

Catalyst Center supports scheduled maintenance for a device, which centrally manages the maintenance window. Events and alerts are handled for that period, and the device returns to normal monitoring afterward.

Why the other options are wrong:

  • A. The Device 360 view shows device health but does not manage a maintenance window.
  • B. Cisco Spaces is a different platform, not the central Catalyst Center process the requirements call for.
  • C. The WLC dashboard is a local view on the controller and does not centrally manage maintenance.

Question 21

How does viewing trend deviation in Cisco Catalyst Center AI Analytics benefit wireless operation?

  • A. It maintains server time synchronization.
  • B. It exports event thresholds to external dashboards.
  • C. It allows earlier notice of abnormal wireless behavior.
  • D. It backs up existing log files to remote hosts.
Show answer and explanation ▾

Correct answer: C

Trend deviation in Catalyst Center AI Analytics compares current behavior with a learned baseline. This helps operators notice abnormal wireless behavior earlier, before users report problems.

Why the other options are wrong:

  • A. Time synchronization is handled by time services, not by AI Analytics.
  • B. Trend deviation is an analysis view, not an export of event thresholds.
  • D. Backing up log files is a separate task unrelated to analyzing trends.

Question 22

What is a benefit of using AI Enhanced RRM over traditional RRM?

  • A. It includes legacy client modes.
  • B. It encrypts stored telemetry results.
  • C. It reacts to current the condition of network.
  • D. It leverages historical data.
Show answer and explanation ▾

Correct answer: D

AI Enhanced RRM uses historical data to make radio decisions, while traditional RRM works mainly from current measurements. This lets it plan channels and power with better knowledge of how the network behaves over time.

Why the other options are wrong:

  • A. Support for legacy client modes is not a benefit specific to AI Enhanced RRM.
  • B. AI Enhanced RRM makes radio decisions and does not encrypt stored telemetry.
  • C. Reacting to current conditions is what traditional RRM already does, so it is not an advantage over it.

Question 23

What does an elevated noise floor indicate in an RF environment?

  • A. decreased link reliability
  • B. stable time synchronization
  • C. enhanced spectrum allocation
  • D. minimized bandwidth demand
Show answer and explanation ▾

Correct answer: A

The noise floor is the background RF energy on a channel. When it rises, the signal-to-noise ratio of clients falls, so frames are corrupted more often and the link becomes less reliable.

Why the other options are wrong:

  • B. Time synchronization is unrelated to background RF energy.
  • C. A higher noise floor leaves less usable spectrum, not a better allocation of it.
  • D. Noise does not reduce demand; clients still want the same bandwidth and have to retry more.

Question 24

How does MIMO operate during wireless transmission?

  • A. It uses multiple radio paths to increase throughput and reliability.
  • B. It applies frequency hopping to prevent crosstalk.
  • C. It shares a single connection among endpoints for coverage expansion.
  • D. It limits data paths to a single antenna for error reduction.
Show answer and explanation ▾

Correct answer: A

MIMO means multiple input, multiple output. It sends and receives over several antennas and spatial paths at once, which raises throughput and makes the link more reliable.

Why the other options are wrong:

  • B. Frequency hopping is a different technique and is not how MIMO works.
  • C. Sharing one connection among endpoints describes multi-user access, not MIMO itself.
  • D. MIMO uses several antennas, the opposite of limiting transmission to one.

Question 25

Which function does FRA use to optimize client experience and network coverage?

  • A. monitoring on the physical interface level in the AP
  • B. enhances roaming by redirecting the client to move to the appropriate AP
  • C. implementation by local data path control
  • D. dynamically adapts the roles of dual-band radios in an AP
Show answer and explanation ▾

Correct answer: D

Flexible Radio Assignment lets an access point with dual-band radios change what each radio does, for example serving clients on 2.4 GHz and 5 GHz or monitoring, depending on the coverage and client load.

Why the other options are wrong:

  • A. Interface-level monitoring is not what FRA does.
  • B. Steering clients to another AP is a roaming or band steering feature.
  • C. Local data path control is a forwarding choice and unrelated to FRA.

Question 26

Which process is managed by Ministry of Internal Affairs and Communications in Japan?

  • A. RF technical standards
  • B. manufacturing batch inspection
  • C. customer onboarding documentation
  • D. supplier chain evaluation
Show answer and explanation ▾

Correct answer: A

In Japan the Ministry of Internal Affairs and Communications is the regional regulator for radio. It sets the technical standards that wireless equipment must meet.

Why the other options are wrong:

  • B. Batch inspection of manufacturing is a company quality process, not a radio regulator task.
  • C. Customer onboarding paperwork is a business matter, not regulated by the ministry as an RF process.
  • D. Supplier chain evaluation is internal to a company and is not an RF regulatory function.

That was 26 of 140.

The full Cisco 350-101 WLCOR pack has all 140 questions, each with the answer, the explanation and why the other options are wrong, plus a questions-only copy for timed runs. $39.00 USD, paid once, with free monthly updates and a pass-or-your-money-back guarantee.

Get the full pack

Not ready yet? Get the first 30 free as one PDF by email. Get the Half Pack →

About the 350-101 exam

These 26 Cisco 350-101 WLCOR questions are free here. The free PDF has 30, free by email.

They are drawn from the same bank as the full 350-101 pack, which has 140 questions in total.

Back to blog